Skip to content

GitLab

Commit c948f771 authored by Yann Gautier's avatar Yann Gautier
Browse files

stm32mp1: update device tree files 



The drivers are also updated to reflect the changes.
Set RCC as non-secure.

Change-Id: I568fa1f418355830ad1d4d1cdcdb910fb362231b
Signed-off-by: default avatarYann Gautier <yann.gautier@st.com>
parent 23684d0e
Show whitespace changes
Inline Side-by-side
drivers/st/ddr/stm32mp1_ddr.c
View file @ c948f771
...@@ -707,7 +707,7 @@ void stm32mp1_ddr_init(struct ddr_info *priv, ...@@ -707,7 +707,7 @@ void stm32mp1_ddr_init(struct ddr_info *priv,
} }
VERBOSE("name = %s\n", config->info.name); VERBOSE("name = %s\n", config->info.name);
VERBOSE("speed = %d MHz\n", config->info.speed); VERBOSE("speed = %d kHz\n", config->info.speed);
VERBOSE("size = 0x%x\n", config->info.size); VERBOSE("size = 0x%x\n", config->info.size);
/* DDR INIT SEQUENCE */ /* DDR INIT SEQUENCE */
......
drivers/st/ddr/stm32mp1_ram.c
View file @ c948f771
/* /*
* Copyright (C) 2018, STMicroelectronics - All Rights Reserved * Copyright (C) 2018-2019, STMicroelectronics - All Rights Reserved
* *
* SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause * SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
*/ */
...@@ -25,7 +25,7 @@ ...@@ -25,7 +25,7 @@
static struct ddr_info ddr_priv_data; static struct ddr_info ddr_priv_data;
int stm32mp1_ddr_clk_enable(struct ddr_info *priv, uint16_t mem_speed) int stm32mp1_ddr_clk_enable(struct ddr_info *priv, uint32_t mem_speed)
{ {
unsigned long ddrphy_clk, ddr_clk, mem_speed_hz; unsigned long ddrphy_clk, ddr_clk, mem_speed_hz;
...@@ -33,10 +33,10 @@ int stm32mp1_ddr_clk_enable(struct ddr_info *priv, uint16_t mem_speed) ...@@ -33,10 +33,10 @@ int stm32mp1_ddr_clk_enable(struct ddr_info *priv, uint16_t mem_speed)
ddrphy_clk = stm32mp1_clk_get_rate(DDRPHYC); ddrphy_clk = stm32mp1_clk_get_rate(DDRPHYC);
VERBOSE("DDR: mem_speed (%d MHz), RCC %ld MHz\n", VERBOSE("DDR: mem_speed (%d kHz), RCC %ld kHz\n",
mem_speed, ddrphy_clk / 1000U / 1000U); mem_speed, ddrphy_clk / 1000U);
mem_speed_hz = (uint32_t)mem_speed * 1000U * 1000U; mem_speed_hz = mem_speed * 1000U;
/* Max 10% frequency delta */ /* Max 10% frequency delta */
if (ddrphy_clk > mem_speed_hz) { if (ddrphy_clk > mem_speed_hz) {
...@@ -44,9 +44,9 @@ int stm32mp1_ddr_clk_enable(struct ddr_info *priv, uint16_t mem_speed) ...@@ -44,9 +44,9 @@ int stm32mp1_ddr_clk_enable(struct ddr_info *priv, uint16_t mem_speed)
} else { } else {
ddr_clk = mem_speed_hz - ddrphy_clk; ddr_clk = mem_speed_hz - ddrphy_clk;
} }
if (ddr_clk > mem_speed_hz) { if (ddr_clk > (mem_speed_hz / 10)) {
ERROR("DDR expected freq %d MHz, current is %ld MHz\n", ERROR("DDR expected freq %d kHz, current is %ld kHz\n",
mem_speed, ddrphy_clk / 1000U / 1000U); mem_speed, ddrphy_clk / 1000U);
return -1; return -1;
} }
return 0; return 0;
...@@ -208,11 +208,16 @@ static int stm32mp1_ddr_setup(void) ...@@ -208,11 +208,16 @@ static int stm32mp1_ddr_setup(void)
return -EINVAL; return -EINVAL;
} }
config.info.speed = config.info.speed = fdt_read_uint32_default(node, "st,mem-speed", 0);
(uint16_t)fdt_read_uint32_default(node, "st,mem-speed", if (!config.info.speed) {
STM32MP1_DDR_SPEED_DFLT); VERBOSE("%s: no st,mem-speed\n", __func__);
config.info.size = fdt_read_uint32_default(node, "st,mem-size", return -EINVAL;
STM32MP1_DDR_SIZE_DFLT); }
config.info.size = fdt_read_uint32_default(node, "st,mem-size", 0);
if (!config.info.size) {
VERBOSE("%s: no st,mem-size\n", __func__);
return -EINVAL;
}
config.info.name = fdt_getprop(fdt, node, "st,mem-name", &len); config.info.name = fdt_getprop(fdt, node, "st,mem-name", &len);
if (config.info.name == NULL) { if (config.info.name == NULL) {
VERBOSE("%s: no st,mem-name\n", __func__); VERBOSE("%s: no st,mem-name\n", __func__);
...@@ -222,7 +227,7 @@ static int stm32mp1_ddr_setup(void) ...@@ -222,7 +227,7 @@ static int stm32mp1_ddr_setup(void)
for (idx = 0; idx < ARRAY_SIZE(param); idx++) { for (idx = 0; idx < ARRAY_SIZE(param); idx++) {
ret = fdt_read_uint32_array(node, param[idx].name, ret = fdt_read_uint32_array(node, param[idx].name,
(void *)((uint32_t)&config + (void *)((uintptr_t)&config +
param[idx].offset), param[idx].offset),
param[idx].size); param[idx].size);
......
drivers/st/mmc/stm32_sdmmc2.c
View file @ c948f771
/* /*
* Copyright (c) 2018, STMicroelectronics - All Rights Reserved * Copyright (c) 2018-2019, STMicroelectronics - All Rights Reserved
* *
* SPDX-License-Identifier: BSD-3-Clause * SPDX-License-Identifier: BSD-3-Clause
*/ */
...@@ -667,15 +667,15 @@ static int stm32_sdmmc2_dt_get_config(void) ...@@ -667,15 +667,15 @@ static int stm32_sdmmc2_dt_get_config(void)
cuint++; cuint++;
sdmmc2_params.reset_id = fdt32_to_cpu(*cuint); sdmmc2_params.reset_id = fdt32_to_cpu(*cuint);
if ((fdt_getprop(fdt, sdmmc_node, "st,pin-ckin", NULL)) != NULL) { if ((fdt_getprop(fdt, sdmmc_node, "st,use-ckin", NULL)) != NULL) {
sdmmc2_params.pin_ckin = SDMMC_CLKCR_SELCLKRX_0; sdmmc2_params.pin_ckin = SDMMC_CLKCR_SELCLKRX_0;
} }
if ((fdt_getprop(fdt, sdmmc_node, "st,dirpol", NULL)) != NULL) { if ((fdt_getprop(fdt, sdmmc_node, "st,sig-dir", NULL)) != NULL) {
sdmmc2_params.dirpol = SDMMC_POWER_DIRPOL; sdmmc2_params.dirpol = SDMMC_POWER_DIRPOL;
} }
if ((fdt_getprop(fdt, sdmmc_node, "st,negedge", NULL)) != NULL) { if ((fdt_getprop(fdt, sdmmc_node, "st,neg-edge", NULL)) != NULL) {
sdmmc2_params.negedge = SDMMC_CLKCR_NEGEDGE; sdmmc2_params.negedge = SDMMC_CLKCR_NEGEDGE;
} }
......
fdts/stm32mp15-ddr.dtsi
View file @ c948f771
...@@ -5,7 +5,7 @@ ...@@ -5,7 +5,7 @@
/ { / {
soc { soc {
ddr: ddr@0x5A003000{ ddr: ddr@5A003000{
compatible = "st,stm32mp1-ddr"; compatible = "st,stm32mp1-ddr";
......
fdts/stm32mp15-ddr3-2x4Gb-1066-binG.dtsi
View file @ c948f771
...@@ -3,7 +3,7 @@ ...@@ -3,7 +3,7 @@
* Copyright (C) 2018, STMicroelectronics - All Rights Reserved * Copyright (C) 2018, STMicroelectronics - All Rights Reserved
*/ */
/* STM32MP157C ED1 and ED2 BOARD configuration /* STM32MP157C ED1 BOARD configuration
* 2x DDR3L 4Gb each, 16-bit, 533MHz, Single Die Package in flyby topology. * 2x DDR3L 4Gb each, 16-bit, 533MHz, Single Die Package in flyby topology.
* Reference used NT5CC256M16DP-DI from NANYA * Reference used NT5CC256M16DP-DI from NANYA
* *
...@@ -15,10 +15,11 @@ ...@@ -15,10 +15,11 @@
* timing mode optimized * timing mode optimized
* Scheduling/QoS options : type = 2 * Scheduling/QoS options : type = 2
* address mapping : RBC * address mapping : RBC
* Tc > + 85C : N
*/ */
#define DDR_MEM_NAME "DDR3-1066 bin G 2x4Gb 533MHz v1.39" #define DDR_MEM_NAME "DDR3-1066/888 bin G 2x4Gb 533MHz v1.41"
#define DDR_MEM_SPEED 533 #define DDR_MEM_SPEED 533000
#define DDR_MEM_SIZE 0x40000000 #define DDR_MEM_SIZE 0x40000000
#define DDR_MSTR 0x00040401 #define DDR_MSTR 0x00040401
...@@ -62,7 +63,7 @@ ...@@ -62,7 +63,7 @@
#define DDR_ADDRMAP11 0x00000000 #define DDR_ADDRMAP11 0x00000000
#define DDR_ODTCFG 0x06000600 #define DDR_ODTCFG 0x06000600
#define DDR_ODTMAP 0x00000001 #define DDR_ODTMAP 0x00000001
#define DDR_SCHED 0x00001201 #define DDR_SCHED 0x00000C01
#define DDR_SCHED1 0x00000000 #define DDR_SCHED1 0x00000000
#define DDR_PERFHPR1 0x01000001 #define DDR_PERFHPR1 0x01000001
#define DDR_PERFLPR1 0x08000200 #define DDR_PERFLPR1 0x08000200
...@@ -74,15 +75,15 @@ ...@@ -74,15 +75,15 @@
#define DDR_PCCFG 0x00000010 #define DDR_PCCFG 0x00000010
#define DDR_PCFGR_0 0x00010000 #define DDR_PCFGR_0 0x00010000
#define DDR_PCFGW_0 0x00000000 #define DDR_PCFGW_0 0x00000000
#define DDR_PCFGQOS0_0 0x02100B03 #define DDR_PCFGQOS0_0 0x02100C03
#define DDR_PCFGQOS1_0 0x00800100 #define DDR_PCFGQOS1_0 0x00800100
#define DDR_PCFGWQOS0_0 0x01100B03 #define DDR_PCFGWQOS0_0 0x01100C03
#define DDR_PCFGWQOS1_0 0x01000200 #define DDR_PCFGWQOS1_0 0x01000200
#define DDR_PCFGR_1 0x00010000 #define DDR_PCFGR_1 0x00010000
#define DDR_PCFGW_1 0x00000000 #define DDR_PCFGW_1 0x00000000
#define DDR_PCFGQOS0_1 0x02100B03 #define DDR_PCFGQOS0_1 0x02100C03
#define DDR_PCFGQOS1_1 0x00800000 #define DDR_PCFGQOS1_1 0x00800040
#define DDR_PCFGWQOS0_1 0x01100B03 #define DDR_PCFGWQOS0_1 0x01100C03
#define DDR_PCFGWQOS1_1 0x01000200 #define DDR_PCFGWQOS1_1 0x01000200
#define DDR_PGCR 0x01442E02 #define DDR_PGCR 0x01442E02
#define DDR_PTR0 0x0022AA5B #define DDR_PTR0 0x0022AA5B
......
fdts/stm32mp157-pinctrl.dtsi
View file @ c948f771
...@@ -3,13 +3,14 @@ ...@@ -3,13 +3,14 @@
* Copyright (C) STMicroelectronics 2017 - All Rights Reserved * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
* Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics. * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
*/ */
#include <dt-bindings/pinctrl/stm32-pinfunc.h> #include <dt-bindings/pinctrl/stm32-pinfunc.h>
/ { / {
soc { soc {
pinctrl: pin-controller { pinctrl: pin-controller@50002000 {
#address-cells = <1>; #address-cells = <1>;
#size-cells = <1>; #size-cells = <1>;
compatible = "st,stm32mp157-pinctrl";
ranges = <0 0x50002000 0xa400>; ranges = <0 0x50002000 0xa400>;
pins-are-numbered; pins-are-numbered;
...@@ -134,54 +135,76 @@ ...@@ -134,54 +135,76 @@
status = "disabled"; status = "disabled";
}; };
uart4_pins_a: uart4@0 { qspi_bk1_pins_a: qspi-bk1-0 {
pins1 { pins1 {
pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */ pinmux = <STM32_PINMUX('F', 8, AF10)>, /* QSPI_BK1_IO0 */
<STM32_PINMUX('F', 9, AF10)>, /* QSPI_BK1_IO1 */
<STM32_PINMUX('F', 7, AF9)>, /* QSPI_BK1_IO2 */
<STM32_PINMUX('F', 6, AF9)>; /* QSPI_BK1_IO3 */
bias-disable; bias-disable;
drive-push-pull; drive-push-pull;
slew-rate = <0>; slew-rate = <1>;
}; };
pins2 { pins2 {
pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */ pinmux = <STM32_PINMUX('B', 6, AF10)>; /* QSPI_BK1_NCS */
bias-disable; bias-pull-up;
drive-push-pull;
slew-rate = <1>;
}; };
}; };
usart3_pins_a: usart3@0 { qspi_bk2_pins_a: qspi-bk2-0 {
pins1 { pins1 {
pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */ pinmux = <STM32_PINMUX('H', 2, AF9)>, /* QSPI_BK2_IO0 */
<STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */ <STM32_PINMUX('H', 3, AF9)>, /* QSPI_BK2_IO1 */
<STM32_PINMUX('G', 10, AF11)>, /* QSPI_BK2_IO2 */
<STM32_PINMUX('G', 7, AF11)>; /* QSPI_BK2_IO3 */
bias-disable; bias-disable;
drive-push-pull; drive-push-pull;
slew-rate = <0>; slew-rate = <1>;
}; };
pins2 { pins2 {
pinmux = <STM32_PINMUX('B', 12, AF8)>, /* USART3_RX */ pinmux = <STM32_PINMUX('C', 0, AF10)>; /* QSPI_BK2_NCS */
<STM32_PINMUX('I', 10, AF8)>; /* USART3_CTS_NSS */ bias-pull-up;
bias-disable; drive-push-pull;
slew-rate = <1>;
}; };
}; };
sdmmc1_b4_pins_a: sdmmc1-b4@0 { qspi_clk_pins_a: qspi-clk-0 {
pins { pins {
pinmux = <STM32_PINMUX('F', 10, AF9)>; /* QSPI_CLK */
bias-disable;
drive-push-pull;
slew-rate = <3>;
};
};
sdmmc1_b4_pins_a: sdmmc1-b4-0 {
pins1 {
pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */ pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
<STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */ <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
<STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */ <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
<STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */ <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
<STM32_PINMUX('C', 12, AF12)>, /* SDMMC1_CK */
<STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */ <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
slew-rate = <3>; slew-rate = <1>;
drive-push-pull;
bias-disable;
};
pins2 {
pinmux = <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
slew-rate = <2>;
drive-push-pull; drive-push-pull;
bias-disable; bias-disable;
}; };
}; };
sdmmc1_dir_pins_a: sdmmc1-dir@0 { sdmmc1_dir_pins_a: sdmmc1-dir-0 {
pins1 { pins1 {
pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */ pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */
<STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */ <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */
<STM32_PINMUX('B', 9, AF11)>; /* SDMMC1_CDIR */ <STM32_PINMUX('B', 9, AF11)>; /* SDMMC1_CDIR */
slew-rate = <3>; slew-rate = <1>;
drive-push-pull; drive-push-pull;
bias-pull-up; bias-pull-up;
}; };
...@@ -191,36 +214,85 @@ ...@@ -191,36 +214,85 @@
}; };
}; };
sdmmc2_b4_pins_a: sdmmc2-b4@0 { sdmmc1_dir_pins_b: sdmmc1-dir-1 {
pins { pins1 {
pinmux = <STM32_PINMUX('E', 12, AF8)>, /* SDMMC1_D0DIR */
<STM32_PINMUX('E', 14, AF11)>, /* SDMMC1_D123DIR */
<STM32_PINMUX('B', 9, AF11)>; /* SDMMC1_CDIR */
slew-rate = <3>;
drive-push-pull;
bias-pull-up;
};
pins2 {
pinmux = <STM32_PINMUX('E', 4, AF8)>; /* SDMMC1_CKIN */
bias-pull-up;
};
};
sdmmc2_b4_pins_a: sdmmc2-b4-0 {
pins1 {
pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */ pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
<STM32_PINMUX('B', 15, AF9)>, /* SDMMC2_D1 */ <STM32_PINMUX('B', 15, AF9)>, /* SDMMC2_D1 */
<STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */ <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
<STM32_PINMUX('B', 4, AF9)>, /* SDMMC2_D3 */ <STM32_PINMUX('B', 4, AF9)>, /* SDMMC2_D3 */
<STM32_PINMUX('E', 3, AF9)>, /* SDMMC2_CK */
<STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */ <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
slew-rate = <3>; slew-rate = <1>;
drive-push-pull;
bias-pull-up;
};
pins2 {
pinmux = <STM32_PINMUX('E', 3, AF9)>; /* SDMMC2_CK */
slew-rate = <2>;
drive-push-pull; drive-push-pull;
bias-pull-up; bias-pull-up;
}; };
}; };
sdmmc2_d47_pins_a: sdmmc2-d47@0 { sdmmc2_d47_pins_a: sdmmc2-d47-0 {
pins { pins {
pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */ pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
<STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */ <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
<STM32_PINMUX('E', 5, AF9)>, /* SDMMC2_D6 */ <STM32_PINMUX('E', 5, AF9)>, /* SDMMC2_D6 */
<STM32_PINMUX('D', 3, AF9)>; /* SDMMC2_D7 */ <STM32_PINMUX('D', 3, AF9)>; /* SDMMC2_D7 */
slew-rate = <3>; slew-rate = <1>;
drive-push-pull; drive-push-pull;
bias-pull-up; bias-pull-up;
}; };
}; };
uart4_pins_a: uart4-0 {
pins1 {
pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
bias-disable;
drive-push-pull;
slew-rate = <0>;
};
pins2 {
pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
bias-disable;
};
};
usart3_pins_a: usart3-0 {
pins1 {
pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
<STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
bias-disable;
drive-push-pull;
slew-rate = <0>;
};
pins2 {
pinmux = <STM32_PINMUX('B', 12, AF8)>, /* USART3_RX */
<STM32_PINMUX('I', 10, AF8)>; /* USART3_CTS_NSS */
bias-disable;
};
};
}; };
pinctrl_z: pin-controller-z { pinctrl_z: pin-controller-z@54004000 {
#address-cells = <1>; #address-cells = <1>;
#size-cells = <1>; #size-cells = <1>;
compatible = "st,stm32mp157-z-pinctrl";
ranges = <0 0x54004000 0x400>; ranges = <0 0x54004000 0x400>;
pins-are-numbered; pins-are-numbered;
...@@ -236,7 +308,7 @@ ...@@ -236,7 +308,7 @@
status = "disabled"; status = "disabled";
}; };
i2c4_pins_a: i2c4@0 { i2c4_pins_a: i2c4-0 {
pins { pins {
pinmux = <STM32_PINMUX('Z', 4, AF6)>, /* I2C4_SCL */ pinmux = <STM32_PINMUX('Z', 4, AF6)>, /* I2C4_SCL */
<STM32_PINMUX('Z', 5, AF6)>; /* I2C4_SDA */ <STM32_PINMUX('Z', 5, AF6)>; /* I2C4_SDA */
......
fdts/stm32mp157c-ed1.dts
View file @ c948f771
...@@ -3,22 +3,28 @@ ...@@ -3,22 +3,28 @@
* Copyright (C) STMicroelectronics 2017 - All Rights Reserved * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
* Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics. * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
*/ */
/dts-v1/; /dts-v1/;
#include "stm32mp157c.dtsi" #include "stm32mp157c.dtsi"
#include "stm32mp157caa-pinctrl.dtsi" #include "stm32mp157caa-pinctrl.dtsi"
/ { / {
model = "STMicroelectronics STM32MP157C-ED1 pmic eval daughter"; model = "STMicroelectronics STM32MP157C eval daughter";
compatible = "st,stm32mp157c-ed1", "st,stm32mp157"; compatible = "st,stm32mp157c-ed1", "st,stm32mp157";
chosen { chosen {
bootargs = "earlyprintk console=ttyS3,115200 root=/dev/ram"; stdout-path = "serial0:115200n8";
stdout-path = "serial3:115200n8"; };
aliases {
serial0 = &uart4;
}; };
}; };
&clk_hse {
st,digbypass;
};
&i2c4 { &i2c4 {
pinctrl-names = "default"; pinctrl-names = "default";
pinctrl-0 = <&i2c4_pins_a>; pinctrl-0 = <&i2c4_pins_a>;
...@@ -29,34 +35,85 @@ ...@@ -29,34 +35,85 @@
pmic: stpmic@33 { pmic: stpmic@33 {
compatible = "st,stpmic1"; compatible = "st,stpmic1";
reg = <0x33>; reg = <0x33>;
interrupts-extended = <&exti_pwr 55 IRQ_TYPE_EDGE_FALLING>;
interrupt-controller;
#interrupt-cells = <2>;
status = "okay"; status = "okay";
st,main_control_register = <0x04>; st,main-control-register = <0x04>;
st,vin_control_register = <0xc0>; st,vin-control-register = <0xc0>;
st,usb_control_register = <0x30>; st,usb-control-register = <0x30>;
regulators { regulators {
compatible = "st,stpmic1-regulators"; compatible = "st,stpmic1-regulators";
ldo1-supply = <&v3v3>;
ldo2-supply = <&v3v3>;
ldo3-supply = <&vdd_ddr>;
ldo5-supply = <&v3v3>;
ldo6-supply = <&v3v3>;
vddcore: buck1 {
regulator-name = "vddcore";
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
regulator-initial-mode = <0>;
regulator-over-current-protection;
};
vdd_ddr: buck2 {
regulator-name = "vdd_ddr";
regulator-min-microvolt = <1350000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
regulator-initial-mode = <0>;
regulator-over-current-protection;
};
vdd: buck3 {
regulator-name = "vdd";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
st,mask-reset;
regulator-initial-mode = <0>;
regulator-over-current-protection;
};
v3v3: buck4 { v3v3: buck4 {
regulator-name = "v3v3"; regulator-name = "v3v3";
regulator-min-microvolt = <3300000>; regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>; regulator-max-microvolt = <3300000>;
regulator-boot-on; regulator-always-on;
regulator-over-current-protection; regulator-over-current-protection;
regulator-initial-mode = <8>; regulator-initial-mode = <0>;
};
regulator-state-standby { vdda: ldo1 {
regulator-suspend-microvolt = <3300000>; regulator-name = "vdda";
regulator-unchanged-in-suspend; regulator-min-microvolt = <2900000>;
regulator-mode = <8>; regulator-max-microvolt = <2900000>;
}; };
regulator-state-mem {
regulator-off-in-suspend; v2v8: ldo2 {
regulator-name = "v2v8";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
}; };
regulator-state-disk {
regulator-off-in-suspend; vtt_ddr: ldo3 {
regulator-name = "vtt_ddr";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <750000>;
regulator-always-on;
regulator-over-current-protection;
}; };
vdd_usb: ldo4 {
regulator-name = "vdd_usb";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
}; };
vdd_sd: ldo5 { vdd_sd: ldo5 {
...@@ -64,24 +121,24 @@ ...@@ -64,24 +121,24 @@
regulator-min-microvolt = <2900000>; regulator-min-microvolt = <2900000>;
regulator-max-microvolt = <2900000>; regulator-max-microvolt = <2900000>;
regulator-boot-on; regulator-boot-on;
regulator-state-standby {
regulator-suspend-microvolt = <2900000>;
regulator-unchanged-in-suspend;
};
regulator-state-mem {
regulator-off-in-suspend;
}; };
regulator-state-disk {
regulator-off-in-suspend; v1v8: ldo6 {
regulator-name = "v1v8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
}; };
vref_ddr: vref_ddr {
regulator-name = "vref_ddr";
regulator-always-on;
regulator-over-current-protection;
}; };
}; };
}; };
}; };
&iwdg2 { &iwdg2 {
instance = <2>;
timeout-sec = <32>; timeout-sec = <32>;
status = "okay"; status = "okay";
}; };
...@@ -90,14 +147,19 @@ ...@@ -90,14 +147,19 @@
status = "okay"; status = "okay";
}; };
&rtc {
status = "okay";
};
&sdmmc1 { &sdmmc1 {
pinctrl-names = "default"; pinctrl-names = "default";
pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>; pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
broken-cd; broken-cd;
st,dirpol; st,sig-dir;
st,negedge; st,neg-edge;
st,pin-ckin; st,use-ckin;
bus-width = <4>; bus-width = <4>;
vmmc-supply = <&vdd_sd>;
sd-uhs-sdr12; sd-uhs-sdr12;
sd-uhs-sdr25; sd-uhs-sdr25;
sd-uhs-sdr50; sd-uhs-sdr50;
...@@ -112,16 +174,17 @@ ...@@ -112,16 +174,17 @@
non-removable; non-removable;
no-sd; no-sd;
no-sdio; no-sdio;
st,dirpol; st,neg-edge;
st,negedge;
bus-width = <8>; bus-width = <8>;
vmmc-supply = <&v3v3>;
vqmmc-supply = <&v3v3>;
mmc-ddr-3_3v;
status = "okay"; status = "okay";
}; };
&uart4 { &uart4 {
pinctrl-names = "default"; pinctrl-names = "default";
pinctrl-0 = <&uart4_pins_a>; pinctrl-0 = <&uart4_pins_a>;
resets = <&rcc UART4_R>;
status = "okay"; status = "okay";
}; };
...@@ -157,6 +220,7 @@ ...@@ -157,6 +220,7 @@
/* CLOCK init */ /* CLOCK init */
&rcc { &rcc {
secure-status = "disabled";
st,clksrc = < st,clksrc = <
CLK_MPU_PLL1P CLK_MPU_PLL1P
CLK_AXI_PLL2P CLK_AXI_PLL2P
...@@ -186,7 +250,7 @@ ...@@ -186,7 +250,7 @@
CLK_FMC_ACLK CLK_FMC_ACLK
CLK_QSPI_ACLK CLK_QSPI_ACLK
CLK_ETH_DISABLED CLK_ETH_DISABLED
CLK_SDMMC12_PLL3R CLK_SDMMC12_PLL4P
CLK_DSI_DSIPLL CLK_DSI_DSIPLL
CLK_STGEN_HSE CLK_STGEN_HSE
CLK_USBPHY_HSE CLK_USBPHY_HSE
...@@ -195,7 +259,7 @@ ...@@ -195,7 +259,7 @@
CLK_SPI45_HSI CLK_SPI45_HSI
CLK_SPI6_HSI CLK_SPI6_HSI
CLK_I2C46_HSI CLK_I2C46_HSI
CLK_SDMMC3_PLL3R CLK_SDMMC3_PLL4P
CLK_USBO_USBPHY CLK_USBO_USBPHY
CLK_ADC_CKPER CLK_ADC_CKPER
CLK_CEC_LSE CLK_CEC_LSE
...@@ -206,17 +270,17 @@ ...@@ -206,17 +270,17 @@
CLK_UART35_HSI CLK_UART35_HSI
CLK_UART6_HSI CLK_UART6_HSI
CLK_UART78_HSI CLK_UART78_HSI
CLK_SPDIF_PLL3Q CLK_SPDIF_PLL4P
CLK_FDCAN_PLL4Q CLK_FDCAN_PLL4Q
CLK_SAI1_PLL3Q CLK_SAI1_PLL3Q
CLK_SAI2_PLL3Q CLK_SAI2_PLL3Q
CLK_SAI3_PLL3Q CLK_SAI3_PLL3Q
CLK_SAI4_PLL3Q CLK_SAI4_PLL3Q
CLK_RNG1_CSI CLK_RNG1_LSI
CLK_RNG2_CSI CLK_RNG2_LSI
CLK_LPTIM1_PCLK1 CLK_LPTIM1_PCLK1
CLK_LPTIM23_PCLK3 CLK_LPTIM23_PCLK3
CLK_LPTIM45_PCLK3 CLK_LPTIM45_LSE
>; >;
/* VCO = 1300.0 MHz => P = 650 (CPU) */ /* VCO = 1300.0 MHz => P = 650 (CPU) */
...@@ -231,15 +295,15 @@ ...@@ -231,15 +295,15 @@
frac = < 0x1400 >; frac = < 0x1400 >;
}; };
/* VCO = 786.4 MHz => P = 197, Q = 49, R = 98 */ /* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
pll3: st,pll@2 { pll3: st,pll@2 {
cfg = < 2 97 3 15 7 PQR(1,1,1) >; cfg = < 1 33 1 16 36 PQR(1,1,1) >;
frac = < 0x9ba >; frac = < 0x1a04 >;
}; };
/* VCO = 508.0 MHz => P = 56, Q = 56, R = 56 */ /* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */
pll4: st,pll@3 { pll4: st,pll@3 {
cfg = < 5 126 8 8 8 PQR(1,1,1) >; cfg = < 3 98 5 7 7 PQR(1,1,1) >;
}; };
}; };
......
fdts/stm32mp157c-ev1.dts
View file @ c948f771
...@@ -3,23 +3,65 @@ ...@@ -3,23 +3,65 @@
* Copyright (C) STMicroelectronics 2017 - All Rights Reserved * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
* Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics. * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
*/ */
/dts-v1/; /dts-v1/;
#include "stm32mp157c-ed1.dts" #include "stm32mp157c-ed1.dts"
/ { / {
model = "STMicroelectronics STM32MP157C-EV1 pmic eval daughter on eval mother"; model = "STMicroelectronics STM32MP157C eval daughter on eval mother";
compatible = "st,stm32mp157c-ev1", "st,stm32mp157c-ed1", "st,stm32mp157"; compatible = "st,stm32mp157c-ev1", "st,stm32mp157c-ed1", "st,stm32mp157";
chosen { chosen {
bootargs = "earlyprintk console=ttyS3,115200 root=/dev/ram"; stdout-path = "serial0:115200n8";
stdout-path = "serial3:115200n8"; };
aliases {
serial1 = &usart3;
};
};
&fmc {
status = "okay";
#address-cells = <1>;
#size-cells = <0>;
nand: nand@0 {
reg = <0>;
nand-on-flash-bbt;
#address-cells = <1>;
#size-cells = <1>;
};
};
&qspi {
pinctrl-names = "default";
pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
flash0: mx66l51235l@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-rx-bus-width = <4>;
spi-max-frequency = <108000000>;
#address-cells = <1>;
#size-cells = <1>;
};
flash1: mx66l51235l@1 {
compatible = "jedec,spi-nor";
reg = <1>;
spi-rx-bus-width = <4>;
spi-max-frequency = <108000000>;
#address-cells = <1>;
#size-cells = <1>;
}; };
}; };
&usart3 { &usart3 {
pinctrl-names = "default"; pinctrl-names = "default";
pinctrl-0 = <&usart3_pins_a>; pinctrl-0 = <&usart3_pins_a>;
resets = <&rcc USART3_R>;
status = "disabled"; status = "disabled";
}; };
fdts/stm32mp157c.dtsi
View file @ c948f771
...@@ -3,7 +3,7 @@ ...@@ -3,7 +3,7 @@
* Copyright (C) STMicroelectronics 2017 - All Rights Reserved * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
* Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics. * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
*/ */
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/stm32mp1-clks.h> #include <dt-bindings/clock/stm32mp1-clks.h>
#include <dt-bindings/reset/stm32mp1-resets.h> #include <dt-bindings/reset/stm32mp1-resets.h>
...@@ -11,15 +11,12 @@ ...@@ -11,15 +11,12 @@
#address-cells = <1>; #address-cells = <1>;
#size-cells = <1>; #size-cells = <1>;
aliases { intc: interrupt-controller@a0021000 {
serial0 = &usart1; compatible = "arm,cortex-a7-gic";
serial1 = &usart2; #interrupt-cells = <3>;
serial2 = &usart3; interrupt-controller;
serial3 = &uart4; reg = <0xa0021000 0x1000>,
serial4 = &uart5; <0xa0022000 0x2000>;
serial5 = &usart6;
serial6 = &uart7;
serial7 = &uart8;
}; };
clocks { clocks {
...@@ -56,7 +53,7 @@ ...@@ -56,7 +53,7 @@
clk_i2s_ckin: i2s_ckin { clk_i2s_ckin: i2s_ckin {
#clock-cells = <0>; #clock-cells = <0>;
compatible = "fixed-clock"; compatible = "fixed-clock";
clock-frequency = <64000000>; clock-frequency = <0>;
}; };
clk_dsi_phy: ck_dsi_phy { clk_dsi_phy: ck_dsi_phy {
...@@ -64,31 +61,28 @@ ...@@ -64,31 +61,28 @@
compatible = "fixed-clock"; compatible = "fixed-clock";
clock-frequency = <0>; clock-frequency = <0>;
}; };
clk_usbo_48m: ck_usbo_48m {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <48000000>;
};
}; };
soc { soc {
compatible = "simple-bus"; compatible = "simple-bus";
#address-cells = <1>; #address-cells = <1>;
#size-cells = <1>; #size-cells = <1>;
interrupt-parent = <&intc>;
ranges; ranges;
usart2: serial@4000e000 { usart2: serial@4000e000 {
compatible = "st,stm32h7-usart"; compatible = "st,stm32h7-uart";
reg = <0x4000e000 0x400>; reg = <0x4000e000 0x400>;
clocks = <&rcc USART2_K>; clocks = <&rcc USART2_K>;
resets = <&rcc USART2_R>;
status = "disabled"; status = "disabled";
}; };
usart3: serial@4000f000 { usart3: serial@4000f000 {
compatible = "st,stm32h7-usart"; compatible = "st,stm32h7-uart";
reg = <0x4000f000 0x400>; reg = <0x4000f000 0x400>;
clocks = <&rcc USART3_K>; clocks = <&rcc USART3_K>;
resets = <&rcc USART3_R>;
status = "disabled"; status = "disabled";
}; };
...@@ -96,6 +90,7 @@ ...@@ -96,6 +90,7 @@
compatible = "st,stm32h7-uart"; compatible = "st,stm32h7-uart";
reg = <0x40010000 0x400>; reg = <0x40010000 0x400>;
clocks = <&rcc UART4_K>; clocks = <&rcc UART4_K>;
resets = <&rcc UART4_R>;
status = "disabled"; status = "disabled";
}; };
...@@ -103,6 +98,7 @@ ...@@ -103,6 +98,7 @@
compatible = "st,stm32h7-uart"; compatible = "st,stm32h7-uart";
reg = <0x40011000 0x400>; reg = <0x40011000 0x400>;
clocks = <&rcc UART5_K>; clocks = <&rcc UART5_K>;
resets = <&rcc UART5_R>;
status = "disabled"; status = "disabled";
}; };
...@@ -111,6 +107,7 @@ ...@@ -111,6 +107,7 @@
compatible = "st,stm32h7-uart"; compatible = "st,stm32h7-uart";
reg = <0x40018000 0x400>; reg = <0x40018000 0x400>;
clocks = <&rcc UART7_K>; clocks = <&rcc UART7_K>;
resets = <&rcc UART7_R>;
status = "disabled"; status = "disabled";
}; };
...@@ -118,21 +115,23 @@ ...@@ -118,21 +115,23 @@
compatible = "st,stm32h7-uart"; compatible = "st,stm32h7-uart";
reg = <0x40019000 0x400>; reg = <0x40019000 0x400>;
clocks = <&rcc UART8_K>; clocks = <&rcc UART8_K>;
resets = <&rcc UART8_R>;
status = "disabled"; status = "disabled";
}; };
usart6: serial@44003000 { usart6: serial@44003000 {
compatible = "st,stm32h7-usart"; compatible = "st,stm32h7-uart";
reg = <0x44003000 0x400>; reg = <0x44003000 0x400>;
clocks = <&rcc USART6_K>; clocks = <&rcc USART6_K>;
resets = <&rcc USART6_R>;
status = "disabled"; status = "disabled";
}; };
sdmmc3: sdmmc@48004000 { sdmmc3: sdmmc@48004000 {
compatible = "st,stm32-sdmmc2"; compatible = "st,stm32-sdmmc2";
reg = <0x48004000 0x400>, <0x48005000 0x400>; reg = <0x48004000 0x400>, <0x48005000 0x400>;
reg-names = "sdmmc", "delay";
clocks = <&rcc SDMMC3_K>; clocks = <&rcc SDMMC3_K>;
clock-names = "apb_pclk";
resets = <&rcc SDMMC3_R>; resets = <&rcc SDMMC3_R>;
cap-sd-highspeed; cap-sd-highspeed;
cap-mmc-highspeed; cap-mmc-highspeed;
...@@ -141,17 +140,34 @@ ...@@ -141,17 +140,34 @@
}; };
rcc: rcc@50000000 { rcc: rcc@50000000 {
compatible = "syscon", "st,stm32mp1-rcc"; compatible = "st,stm32mp1-rcc", "syscon";
reg = <0x50000000 0x1000>;
#clock-cells = <1>; #clock-cells = <1>;
#reset-cells = <1>; #reset-cells = <1>;
reg = <0x50000000 0x1000>; interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
}; };
rcc_reboot: rcc-reboot@50000000 { pwr: pwr@50001000 {
compatible = "syscon-reboot"; compatible = "st,stm32mp1-pwr", "syscon", "simple-mfd";
regmap = <&rcc>; reg = <0x50001000 0x400>;
offset = <0x404>; };
mask = <0x1>;
exti: interrupt-controller@5000d000 {
compatible = "st,stm32mp1-exti", "syscon";
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x5000d000 0x400>;
/* exti_pwr is an extra interrupt controller used for
* EXTI 55 to 60. It's mapped on pwr interrupt
* controller.
*/
exti_pwr: exti-pwr {
interrupt-controller;
#interrupt-cells = <2>;
interrupt-parent = <&pwr>;
st,irq-number = <6>;
};
}; };
rng1: rng@54003000 { rng1: rng@54003000 {
...@@ -162,13 +178,15 @@ ...@@ -162,13 +178,15 @@
status = "disabled"; status = "disabled";
}; };
fmc_nand: fmc_nand@58002000 { fmc: nand-controller@58002000 {
compatible = "st,stm32mp1-fmc"; compatible = "st,stm32mp15-fmc2";
reg = <0x58002000 0x1000>, reg = <0x58002000 0x1000>,
<0x80000000 0x40000>, <0x80000000 0x1000>,
<0x81000000 0x40000>, <0x88010000 0x1000>,
<0x88000000 0x40000>, <0x88020000 0x1000>,
<0x89000000 0x40000>; <0x81000000 0x1000>,
<0x89010000 0x1000>,
<0x89020000 0x1000>;
clocks = <&rcc FMC_K>; clocks = <&rcc FMC_K>;
resets = <&rcc FMC_R>; resets = <&rcc FMC_R>;
status = "disabled"; status = "disabled";
...@@ -177,15 +195,17 @@ ...@@ -177,15 +195,17 @@
qspi: qspi@58003000 { qspi: qspi@58003000 {
compatible = "st,stm32f469-qspi"; compatible = "st,stm32f469-qspi";
reg = <0x58003000 0x1000>, <0x70000000 0x10000000>; reg = <0x58003000 0x1000>, <0x70000000 0x10000000>;
reg-names = "qspi", "qspi_mm";
clocks = <&rcc QSPI_K>; clocks = <&rcc QSPI_K>;
resets = <&rcc QSPI_R>;
status = "disabled"; status = "disabled";
}; };
sdmmc1: sdmmc@58005000 { sdmmc1: sdmmc@58005000 {
compatible = "st,stm32-sdmmc2"; compatible = "st,stm32-sdmmc2";
reg = <0x58005000 0x1000>, <0x58006000 0x1000>; reg = <0x58005000 0x1000>, <0x58006000 0x1000>;
reg-names = "sdmmc", "delay";
clocks = <&rcc SDMMC1_K>; clocks = <&rcc SDMMC1_K>;
clock-names = "apb_pclk";
resets = <&rcc SDMMC1_R>; resets = <&rcc SDMMC1_R>;
cap-sd-highspeed; cap-sd-highspeed;
cap-mmc-highspeed; cap-mmc-highspeed;
...@@ -196,8 +216,8 @@ ...@@ -196,8 +216,8 @@
sdmmc2: sdmmc@58007000 { sdmmc2: sdmmc@58007000 {
compatible = "st,stm32-sdmmc2"; compatible = "st,stm32-sdmmc2";
reg = <0x58007000 0x1000>, <0x58008000 0x1000>; reg = <0x58007000 0x1000>, <0x58008000 0x1000>;
reg-names = "sdmmc", "delay";
clocks = <&rcc SDMMC2_K>; clocks = <&rcc SDMMC2_K>;
clock-names = "apb_pclk";
resets = <&rcc SDMMC2_R>; resets = <&rcc SDMMC2_R>;
cap-sd-highspeed; cap-sd-highspeed;
cap-mmc-highspeed; cap-mmc-highspeed;
...@@ -205,7 +225,7 @@ ...@@ -205,7 +225,7 @@
status = "disabled"; status = "disabled";
}; };
iwdg2: iwdg@5a002000 { iwdg2: watchdog@5a002000 {
compatible = "st,stm32mp1-iwdg"; compatible = "st,stm32mp1-iwdg";
reg = <0x5a002000 0x400>; reg = <0x5a002000 0x400>;
clocks = <&rcc IWDG2>, <&rcc CK_LSI>; clocks = <&rcc IWDG2>, <&rcc CK_LSI>;
...@@ -214,15 +234,34 @@ ...@@ -214,15 +234,34 @@
}; };
usart1: serial@5c000000 { usart1: serial@5c000000 {
compatible = "st,stm32h7-usart"; compatible = "st,stm32h7-uart";
reg = <0x5c000000 0x400>; reg = <0x5c000000 0x400>;
interrupt-names = "event", "wakeup";
interrupts-extended = <&intc GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>,
<&exti 26 1>;
clocks = <&rcc USART1_K>; clocks = <&rcc USART1_K>;
resets = <&rcc USART1_R>;
status = "disabled";
};
spi6: spi@5c001000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32h7-spi";
reg = <0x5c001000 0x400>;
interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc SPI6_K>;
resets = <&rcc SPI6_R>;
status = "disabled"; status = "disabled";
}; };
i2c4: i2c@5c002000 { i2c4: i2c@5c002000 {
compatible = "st,stm32f7-i2c"; compatible = "st,stm32f7-i2c";
reg = <0x5c002000 0x400>; reg = <0x5c002000 0x400>;
interrupt-names = "event", "error", "wakeup";
interrupts-extended = <&intc GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
<&intc GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
<&exti 24 1>;
clocks = <&rcc I2C4_K>; clocks = <&rcc I2C4_K>;
resets = <&rcc I2C4_R>; resets = <&rcc I2C4_R>;
#address-cells = <1>; #address-cells = <1>;
...@@ -235,6 +274,36 @@ ...@@ -235,6 +274,36 @@
reg = <0x5c004000 0x400>; reg = <0x5c004000 0x400>;
clocks = <&rcc RTCAPB>, <&rcc RTC>; clocks = <&rcc RTCAPB>, <&rcc RTC>;
clock-names = "pclk", "rtc_ck"; clock-names = "pclk", "rtc_ck";
interrupts-extended = <&intc GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
<&exti 19 1>;
status = "disabled";
};
bsec: nvmem@5c005000 {
compatible = "st,stm32mp15-bsec";
reg = <0x5c005000 0x400>;
#address-cells = <1>;
#size-cells = <1>;
ts_cal1: calib@5c {
reg = <0x5c 0x2>;
};
ts_cal2: calib@5e {
reg = <0x5e 0x2>;
};
};
i2c6: i2c@5c009000 {
compatible = "st,stm32f7-i2c";
reg = <0x5c009000 0x400>;
interrupt-names = "event", "error", "wakeup";
interrupts-extended = <&intc GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
<&intc GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
<&exti 54 1>;
clocks = <&rcc I2C6_K>;
resets = <&rcc I2C6_R>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
}; };
}; };
}; };
fdts/stm32mp157caa-pinctrl.dtsi
View file @ c948f771
...@@ -7,8 +7,8 @@ ...@@ -7,8 +7,8 @@
#include "stm32mp157-pinctrl.dtsi" #include "stm32mp157-pinctrl.dtsi"
/ { / {
soc { soc {
pinctrl: pin-controller { pinctrl: pin-controller@50002000 {
compatible = "st,stm32mp157caa-pinctrl"; st,package = <STM32MP157CAA>;
gpioa: gpio@50002000 { gpioa: gpio@50002000 {
status = "okay"; status = "okay";
...@@ -77,8 +77,8 @@ ...@@ -77,8 +77,8 @@
}; };
}; };
pinctrl_z: pin-controller-z { pinctrl_z: pin-controller-z@54004000 {
compatible = "st,stm32mp157caa-z-pinctrl"; st,package = <STM32MP157CAA>;
gpioz: gpio@54004000 { gpioz: gpio@54004000 {
status = "okay"; status = "okay";
......
include/drivers/st/stm32mp1_ddr.h
View file @ c948f771
/* /*
* Copyright (C) 2018, STMicroelectronics - All Rights Reserved * Copyright (C) 2018-2019, STMicroelectronics - All Rights Reserved
* *
* SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause * SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
*/ */
...@@ -153,7 +153,7 @@ struct stm32mp1_ddrphy_cal { ...@@ -153,7 +153,7 @@ struct stm32mp1_ddrphy_cal {
struct stm32mp1_ddr_info { struct stm32mp1_ddr_info {
const char *name; const char *name;
uint16_t speed; /* in MHZ */ uint32_t speed; /* in kHZ */
uint32_t size; /* Memory size in byte = col * row * width */ uint32_t size; /* Memory size in byte = col * row * width */
}; };
...@@ -168,7 +168,7 @@ struct stm32mp1_ddr_config { ...@@ -168,7 +168,7 @@ struct stm32mp1_ddr_config {
struct stm32mp1_ddrphy_cal p_cal; struct stm32mp1_ddrphy_cal p_cal;
}; };
int stm32mp1_ddr_clk_enable(struct ddr_info *priv, uint16_t mem_speed); int stm32mp1_ddr_clk_enable(struct ddr_info *priv, uint32_t mem_speed);
void stm32mp1_ddr_init(struct ddr_info *priv, void stm32mp1_ddr_init(struct ddr_info *priv,
struct stm32mp1_ddr_config *config); struct stm32mp1_ddr_config *config);
#endif /* STM32MP1_DDR_H */ #endif /* STM32MP1_DDR_H */
include/dt-bindings/interrupt-controller/arm-gic.h 0 → 100644
View file @ c948f771
/* SPDX-License-Identifier: GPL-2.0 or BSD-3-Clause */
/*
* This header provides constants for the ARM GIC.
*/
#ifndef _DT_BINDINGS_INTERRUPT_CONTROLLER_ARM_GIC_H
#define _DT_BINDINGS_INTERRUPT_CONTROLLER_ARM_GIC_H
/* interrupt specifier cell 0 */
#define GIC_SPI 0
#define GIC_PPI 1
#define IRQ_TYPE_NONE 0
#define IRQ_TYPE_EDGE_RISING 1
#define IRQ_TYPE_EDGE_FALLING 2
#define IRQ_TYPE_EDGE_BOTH (IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING)
#define IRQ_TYPE_LEVEL_HIGH 4
#define IRQ_TYPE_LEVEL_LOW 8
#endif
include/dt-bindings/pinctrl/stm32-pinfunc.h
View file @ c948f771
...@@ -32,4 +32,10 @@ ...@@ -32,4 +32,10 @@
#define STM32_PINMUX(port, line, mode) (((PIN_NO(port, line)) << 8) | (mode)) #define STM32_PINMUX(port, line, mode) (((PIN_NO(port, line)) << 8) | (mode))
/* package information */
#define STM32MP157CAA 0x1
#define STM32MP157CAB 0x2
#define STM32MP157CAC 0x4
#define STM32MP157CAD 0x8
#endif /* _DT_BINDINGS_STM32_PINFUNC_H */ #endif /* _DT_BINDINGS_STM32_PINFUNC_H */
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment