GitLab

This patch adds soc_fw_config, tos_fw_config and nt_fw_config to the FVP.
The config files are placeholders and do not have any useful bindings
defined. The tos_fw_config is packaged in FIP and loaded by BL2 only
if SPD=tspd. The load address of these configs are specified in tb_fw_config
via new bindings defined for these configs. Currently, in FVP, the
soc_fw_config and tos_fw_config is loaded in the page between BL2_BASE
and ARM_SHARED_RAM. This memory was typically used for BL32 when
ARM_TSP_RAM_LOCATION=tsram but since we cannot fit BL32 in that
space anymore, it should be safe to use this memory for these configs.
There is also a runtime check in arm_bl2_dyn_cfg_init() which ensures
that this overlap doesn't happen.

The previous arm_dyn_get_hwconfig_info() is modified to accept configs
other than hw_config and hence renamed to arm_dyn_get_config_load_info().
The patch also corrects the definition of ARM_TB_FW_CONFIG_LIMIT to be
BL2_BASE.

Change-Id: I03a137d9fa1f92c862c254be808b8330cfd17a5a
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch adds capability to FVP to disable authentication dynamically
via the `disable_auth` property in TB_FW_CONFIG. Both BL1 and BL2 parses
the TB_FW_CONFIG for the `disable_auth` property and invokes the
`load_dyn_disable_auth()` API to disable authentication if the
property is set to 1. The DYN_DISABLE_AUTH is enabled by default for
FVP as it is a development platform. Note that the TB_FW_CONFIG has to
be authenticated by BL1 irrespective of these settings.

The arm_bl2_dyn_cfg_init() is now earlier in bl2_plat_preload_setup()
rather than in bl2_platform_setup() as we need to get the value of
`disable_auth` property prior to authentication of any image by BL2.

Change-Id: I734acd59572849793e5020ec44c6ac51f654a4d1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

The patch adds the necessary changes to load HW_CONFIG in BL2 for
ARM Platforms :

1. The load address of HW_CONFIG is specified via the `hw_config_addr`
property in TB_FW_CONFIG is loaded by BL1. The `hw_config_max_size`
property defines the maximum size to be expected for the HW_CONFIG.
The `arm_dyn_cfg_helpers.c` and corresponding header implements
utility functions to parse these DT properties defined.
The `arm_dyn_cfg.c` implements wrappers to these helpers to enable
them to be invoked from ARM platform layer.

2. `HW_CONFIG` is added to the `bl2_mem_params_descs[]` array which is
the list of images to be loaded by BL2.

3. The `libfdt` sources are now included when BL2 is built

4. A new helper `populate_next_bl_params_config()` is introduced in
desc_image_load.c to populate the subsequent executable BL images
with the `hw_config` and the corresponding `fw_config` if available.
The `plat_get_next_bl_params()` API for ARM platforms is modified to
invoke this new helper.

5. The implementation of `bl2_early_platform_setup2()` is modified to
consider `arg0` as well in addition to `arg1` passed from BL1.

6. Bump up the BL2 size for Juno to accommodate the inclusion of libfdt.

Change-Id: I80f1554adec41753e0d179a5237364f04fe13a3f
Signed-off-by: Soby Mathew <soby.mathew@arm.com>