GitLab

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/



Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

On Tegra systems, there are multiple software components that
require to interact with MCE. The components can either be 32-bit
or 64-bit payloads. This patch supports MCE SMC functions ID for
AARCH32 and AARCH64 architectures to support such clients.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds support for fake system suspend (SC7).
This is a debug mode, to ensure that a different code path is
executed for cases like pre-silicon development, where a
full-fledged SC7 is not possible in early stages.

This particular patch ensures that, if fake system suspend is
enabled (denoted by tegra_fake_system_suspend variable
having a non-zero value), instead of calling WFI, a request
for a warm reset is made for starting the SC7 exit procedure.

This ensures that the code path of kernel->ATF and back to
kernel is executed without depending on other components
involved in SC7 code path.

Additionally, this patch also adds support for SMC call
from kernel, enabling fake system suspend mode.
Signed-off-by: Vignesh Radhakrishnan <vigneshr@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch allows the NS world to pass 64-bit base address for
the Video Memory carveout region.

Change-Id: I7e47cc1f5425bd39c6763755b801517013e1e0cd
Signed-off-by: Harvey Hsieh <hhsieh@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds a handler for FIQ interrupts triggered when
the CPU is in the NS world. The handler stores the NS world's
context along with ELR_EL3/SPSR_EL3.

The NS world driver issues an SMC initially to register it's
handler. The monitor firmware stores this handler address and
jumps to it when the FIQ interrupt fires. Upon entry into the
NS world the driver then issues another SMC to get the CPU
context when the FIQ fired. This allows the NS world driver to
determine the CPU state and call stack when the interrupt
fired. Generally, systems register watchdog interrupts as FIQs
which are then used to get the CPU state during hangs/crashes.

Change-Id: I733af61a08d1318c75acedbe9569a758744edd0c
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch removes the restriction of allowing SiP calls only from the
non-secure world. The secure world can issue SiP calls as a result of
this patch now.

Change-Id: Idd64e893ae8e114bba0196872d3ec544cac150bf
Signed-off-by: Wayne Lin <wlin@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch implements a handler for common SiP calls. A weak
implementation for the SoC-specific handler has been provided
which can be overridden by SoCs to implement any custom SiP
calls.

Change-Id: I45122892a84ea35d7b44be0f35dc15f6bb95193e
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch converts the common SiP handler to SoC specific SiP
handler. T210 and T132 have different SiP SMCs and so it makes
sense to move the SiP handler to soc/t132 and soc/t210 folders.

Change-Id: Idfe48384d63641137d74a095432df4724986b241
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch implements support for T132 (Denver CPU) based Tegra
platforms.

The following features have been added:

* SiP calls to switch T132 CPU's AARCH mode
* Complete PSCI support, including 'System Suspend'
* Platform specific MMIO settings
* Locking of CPU vector registers
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds support to reserve a memory carveout region in the
DRAM on Tegra SoCs. The memory controller provides specific registers
to specify the aperture's base and size. This aperture can also be
changed dynamically in order to re-size the memory available for
DRM video playback. In case of the new aperture not overlapping
the previous one, the previous aperture has to be cleared before
setting up the new one. This means we do not "leak" any video data
to the NS world.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

The communication protocol used between the AP cores and the SCP
in CSS-based platforms like Juno has undergone a number of changes.
This patch makes the required modifications to the SCP Boot Protocol,
SCPI Protocol and MHU driver code in shared CSS platform code so that
the AP cores are still able to communicate with the SCP.

This patch focuses on the mandatory changes to make it work. The
design of this code needs to be improved but this will come in
a subsequent patch.

The main changes are:

 - MHU communication protocol

   - The command ID and payload size are no longer written into the
     MHU registers directly. Instead, they are stored in the payload
     area. The MHU registers are now used only as a doorbell to kick
     off messages. Same goes for any command result, the AP has to
     pick it up from the payload area.

 - SCP Boot Protocol

   - The BL3-0 image is now expected to embed a checksum. This
     checksum must be passed to the SCP, which uses it to check the
     integrity of the image it received.

   - The BL3-0 image used to be transferred a block (4KB)
     at a time. The SCP now supports receiving up to 128KB at a
     time, which is more than the size of the BL3-0 image.
     Therefore, the image is now sent in one go.

   - The command IDs have changed.

 - SCPI Protocol

   - The size of the SCPI payload has been reduced down from 512
     bytes to 256 bytes. This changes the base address of the
     AP-to-SCP payload area.

   - For commands that have a response, the response is the same SCPI
     header that was sent, except for the size and the status, which
     both must be updated appropriately. Success/Failure of a command
     is determined by looking at the updated status code.

   - Some command IDs have changed.

NOTE: THIS PATCH BREAKS COMPATIBILITY WITH FORMER VERSIONS OF THE SCP
FIRMWARE AND THUS REQUIRES AN UPDATE OF THIS BINARY. THE LATEST SCP
BINARY CAN BE OBTAINED FROM THE ARM CONNECTED COMMUNITY WEBSITE.

Change-Id: Ia5f6b95fe32401ee04a3805035748e8ef6718da7

This major change pulls out the common functionality from the
FVP and Juno platform ports into the following categories:

*   (include/)plat/common. Common platform porting functionality that
typically may be used by all platforms.

*   (include/)plat/arm/common. Common platform porting functionality
that may be used by all ARM standard platforms. This includes all
ARM development platforms like FVP and Juno but may also include
non-ARM-owned platforms.

*   (include/)plat/arm/board/common. Common platform porting
functionality for ARM development platforms at the board
(off SoC) level.

*   (include/)plat/arm/css/common. Common platform porting
functionality at the ARM Compute SubSystem (CSS) level. Juno
is an example of a CSS-based platform.

*   (include/)plat/arm/soc/common. Common platform porting
functionality at the ARM SoC level, which is not already defined
at the ARM CSS level.

No guarantees are made about the backward compatibility of
functionality provided in (include/)plat/arm.

Also remove any unnecessary variation between the ARM development
platform ports, including:

*   Unify the way BL2 passes `bl31_params_t` to BL3-1. Use the
Juno implementation, which copies the information from BL2 memory
instead of expecting it to persist in shared memory.

*   Unify the TZC configuration. There is no need to add a region
for SCP in Juno; it's enough to simply not allow any access to
this reserved region. Also set region 0 to provide no access by
default instead of assuming this is the case.

*   Unify the number of memory map regions required for ARM
development platforms, although the actual ranges mapped for each
platform may be different. For the FVP port, this reduces the
mapped peripheral address space.

These latter changes will only be observed when the platform ports
are migrated to use the new common platform code in subsequent
patches.

Change-Id: Id9c269dd3dc6e74533d0e5116fdd826d53946dc8

* Move TSP platform porting functions to new file:
  include/bl32/tsp/platform_tsp.h.

* Create new TSP_IRQ_SEC_PHY_TIMER definition for use by the generic
  TSP interrupt handling code, instead of depending on the FVP
  specific definition IRQ_SEC_PHY_TIMER.

* Rename TSP platform porting functions from bl32_* to tsp_*, and
  definitions from BL32_* to TSP_*.

* Update generic TSP code to use new platform porting function names
  and definitions.

* Update FVP port accordingly and move all TSP source files to:
  plat/fvp/tsp/.

* Update porting guide with above changes.

Note: THIS CHANGE REQUIRES ALL PLATFORM PORTS OF THE TSP TO
      BE UPDATED

Fixes ARM-software/tf-issues#167

Change-Id: Ic0ff8caf72aebb378d378193d2f017599fc6b78f

Reduce the number of header files included from other header
files as much as possible without splitting the files. Use forward
declarations where possible. This allows removal of some unnecessary
"#ifndef __ASSEMBLY__" statements.

Also, review the .c and .S files for which header files really need
including and reorder the #include statements alphabetically.

Fixes ARM-software/tf-issues#31

Change-Id: Iec92fb976334c77453e010b60bcf56f3be72bd3e

Change-Id: Ic7fb61aabae1d515b9e6baf3dd003807ff42da60

- Add instructions for contributing to ARM Trusted Firmware.

- Update copyright text in all files to acknowledge contributors.

Change-Id: I9311aac81b00c6c167d2f8c889aea403b84450e5