GitLab

While the Allwinner platform code nominally supported a custom
PRELOADED_BL33_BASE, some references to the BL33 load address used
another constant: PLAT_SUNXI_NS_IMAGE_OFFSET. To allow the DTB search
code to work if a U-Boot BL33 is loaded to a custom address,
consistently use PRELOADED_BL33_BASE. And to avoid this confusion in
the future, remove the other constant.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Ie6b97ae1fdec95d784676aef39200bef161471b0

If an SCP firmware is present and able to communicate via SCPI, then use
that to implement CPU and system power state transitions, including CPU
hotplug and system suspend. Otherwise, fall back to the existing CPU
power control implementation.

The last 16 KiB of SRAM A2 are reserved for the SCP firmware, and the
SCPI shared memory is at the very end of this region (and therefore the
end of SRAM A2). BL31 continues to start at the beginning of SRAM A2
(not counting the ARISC exception vector area) and fills up to the
beginning of the SCP firmware.

Because the SCP firmware is not loaded adjacent to the ARISC exception
vector area, the jump instructions used for exception handling cannot be
included in the SCP firmware image, and must be initialized here before
turning on the SCP.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I37b9b9636f94d4125230423726f3ac5e9cdb551c

The SCP firmware is allocated the last 16KiB of SRAM A2. This includes
the SCPI shared memory area, which must be mapped as MT_DEVICE to
prevent problems with cache coherency between the AP CPUs and the SCP.
For simplicity, map the whole SCP region as MT_DEVICE.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Ie39eb5ff281b8898a3c1d9748dc08755f528e2f8

The ARISC vector area consists of 0x4000 bytes before the beginning of
usable SRAM. Still, it is technically a part of SRAM A2, so include it
in the memory definition. This avoids the confusing practice of
subtracting from the beginning of the SRAM region when referencing the
ARISC vectors.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Iae89e01aeab93560159562692e03e88306e2a1bf

PLATFORM_CORE_COUNT - Unsigned int
PLATFORM_CLUSTER_COUNT - Unsigned int
PLATFORM_MAX_CPUS_PER_CLUSTER - Unsigned int
PLATFORM_CORE_COUNT_PER_CLUSTER - Unsigned int
Signed-off-by: Deepika Bhavnani <deepika.bhavnani@arm.com>
Change-Id: I7aea86891e54522c88af5ff16795a575f9a9322d

Remove the general BL31 mmap region: it duplicates the existing static
mapping for the entire SRAM region. Use the helper definitions when
applicable to simplify the code and add the MT_EXECUTE_NEVER flag.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I7a6b79e50e4b5c698774229530dd3d2a89e94a6d

Now that there is plenty of space (32 KiB) available for NOBITS
sections, we can afford using an entire page for coherent memory. In
fact, because it simplifies the code, this is a beneficial change for
loaded image (.text) size, where we are still close to the size limit.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I0b899dabcb162015c63b0e4aed0869569c889ed9

This frees up space in SRAM A2 that will be used by the SCP firmware and
SCPI shared memory.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I8ce035257451e2d142666fe0cd045e59d4d57b35

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}

The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).

For example, this patch had to be created because two headers were
called the same way: e0ea0928 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3 ("drivers: add tzc380 support").

This problem was introduced in commit 4ecca339

 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.

Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.

Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The initial PMIC setup for the Allwinner platform is quite board
specific, and used to be guarded by reading the .dtb stub *name* from the
SPL image in the legacy ATF port. This doesn't scale particularly well,
and requires constant maintainance.
Instead having the actual .dtb available would be much better, as the PMIC
setup requirements could be read from there directly.
The only available BL33 for Allwinner platforms so far is U-Boot, and
fortunately U-Boot comes with the full featured .dtb, appended to the
end of the U-Boot image.

Introduce some code that scans the beginning of the BL33 image to look
for the load address, which is followed by the image size. Adding those
two values together gives us the end of the image and thus the .dtb
address. Verify that this heuristic is valid by sanitising some values
and checking the DTB magic.

Print out the DTB address and the model name, if specified in the root
node.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

According to the documentation, platforms may choose to trade memory
footprint for performance (and elegancy) by not providing a separately
mapped coherent page.

Since a debug build is getting close to the SRAM size limit already, this
allows us to save about 3.5KB of BSS and have some room for future
enhancements.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

At the moment we map as much of the DRAM into EL3 as possible, however
we actually don't use it. The only exception is the secure DRAM for
BL32 (if that is configured).

To decrease the memory footprint of ATF, we save on some page tables by
reducing the memory mapping to the actually required regions: SRAM, device
MMIO, secure DRAM and U-Boot (to be used later).
This introduces a non-identity mapping for the DRAM regions.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Also change header guards to fix defects of MISRA C-2012 Rule 21.1.

Change-Id: Ied0d4b0e557ef6119ab669d106d2ac5d99620c57
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

There is nothing we need from the BootROM area, so we also don't need
to map it in EL3.

Remove the mapping and reduce the number of MMAP regions by one.
Reported-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

This patch is an attempt to run Trusted OS (OP-TEE OS being one of them) along
side BL31 image.

ATF supports multiple SPD's that can take dispatcher name (opteed for OP-TEE OS)
as an input using the 'SPD=<dispatcher name>' option during bl31 build.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>

This patch is an attempt to run Trusted OS (OP-TEE OS being one of them) along
side BL31 image.

ATF supports multiple SPD's that can take dispatcher name (opteed for OP-TEE OS)
as an input using the 'SPD=<dispatcher name>' option during bl31 build.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>

This platform supports Allwinner's SoCs with ARMv8 cores. So far they
all sport a single cluster of Cortex-A53 cores.

"sunxi" is the original code name used for this platform, and since it
appears in the Linux kernel and in U-Boot as well, we use it here as a
short file name prefix and for identifiers.

This port includes BL31 support only. U-Boot's SPL takes the role of the
primary loader, also doing the DRAM initialization. It then loads the
rest of the firmware, namely ATF and U-Boot (BL33), then hands execution
over to ATF.

This commit includes the basic platform code shared across all SoCs.
There is no platform.mk yet.

[Andre: moved files into proper directories, supported RESET_TO_BL31,
	various clean ups and simplifications ]
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>