GitLab

NOTE: AARCH32/AARCH64 macros are now deprecated in favor of __aarch64__.

All common C compilers pre-define the same macros to signal which
architecture the code is being compiled for: __arm__ for AArch32 (or
earlier versions) and __aarch64__ for AArch64. There's no need for TF-A
to define its own custom macros for this. In order to unify code with
the export headers (which use __aarch64__ to avoid another dependency),
let's deprecate the AARCH32 and AARCH64 macros and switch the code base
over to the pre-defined standard macro. (Since it is somewhat
unintuitive that __arm__ only means AArch32, let's standardize on only
using __aarch64__.)

Change-Id: Ic77de4b052297d77f38fc95f95f65a8ee70cf200
Signed-off-by: Julius Werner <jwerner@chromium.org>

N1SDP platform supports RDIMMs with ECC capability. To use the ECC
capability, the entire DDR memory space has to be zeroed out before
enabling the ECC bits in DMC620. Zeroing out several gigabytes of
memory from SCP is quite time consuming so functions are added that
zeros out the DDR memory from application processor which is
much faster compared to SCP. BL33 binary cannot be copied to DDR memory
before enabling ECC so this is also done by TF-A from IOFPGA-DDR3
memory to main DDR4 memory after ECC is enabled.

Original PLAT_PHY_ADDR_SPACE_SIZE was limited to 36-bits with which
the entire DDR space cannot be accessed as DRAM2 starts in base
0x8080000000. So these macros are redefined for all ARM platforms.

Change-Id: If09524fb65b421b7a368b1b9fc52c49f2ddb7846
Signed-off-by: Manoj Kumar <manoj.kumar3@arm.com>

The default DRAM2 base address for Arm platforms
is 0x880000000. However, on some platforms the
firmware may want to move the start address to
a different value.

To support this introduce PLAT_ARM_DRAM2_BASE that
defaults to 0x880000000; but can be overridden by
a platform (e.g. in platform_def.h).

Change-Id: I0d81195e06070bc98f376444b48ada2db1666e28
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>

When RECLAIM_INIT_CODE is 1, the stack is used to contain the .text.init
section. This is by default enable on FVP. Due to the size increase of
the .text.init section, the stack had to be adjusted contain it.

Change-Id: Ia392341970fb86c0426cf2229b1a7295453e2e32
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

This patch adds support for Versatile express FVP (Fast models).
Versatile express is a family of platforms that are based on ARM v7.
Currently this port has only been tested on Cortex A7, although it
should work with other ARM V7 cores that support LPAE, generic timers,
VFP and hardware divide. Future patches will support other
cores like Cortex A5 that dont support features like LPAE
and hardware divide. This platform is tested on and only expected to
work on single core models.

Change-Id: I10893af65b8bb64da7b3bd851cab8231718e61dd
Signed-off-by: Usama Arif <usama.arif@arm.com>

The variable is renamed to PLAT_ARM_RUN_UART as
the UART is used outside BL31 as well.

Change-Id: I00e3639dfb2001758b7d24548c11236c6335f64a
Signed-off-by: Usama Arif <usama.arif@arm.com>

PLAT_ARM_NS_IMAGE_OFFSET is in fact not an offset relative to some base
address, it is an absolute address. Rename it to avoid any confusion.

Change-Id: I1f7f5e8553cb267786afe7e5f3cd4d665b610d3f
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

The PLAT_XLAT_TABLES_DYNAMIC build option, defined in platform_def.h
in Arm platforms, is checked by several headers, affecting their
behaviour. To avoid issues around the include ordering of the headers,
the definition should be moved to the platform's makefile.

Change-Id: I0e12365c8d66309122e8a20790e1641a4f480a10
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Use full include paths like it is done for common includes.

This cleanup was started in commit d40e0e08283a ("Sanitise includes
across codebase"), but it only cleaned common files and drivers. This
patch does the same to Arm platforms.

Change-Id: If982e6450bbe84dceb56d464e282bcf5d6d9ab9b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The SPM implementation based on MM is going to be kept for the
foreseeable future.

Change-Id: I11e96778a4f52a1aa803e7e048d9a7cb24a53954
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>

Update some asserts that refer to #defines that only occur in
ARM platforms, preventing this code to be used on other platforms.
Instead, use a platform agnostic name, and update all the existing
users.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}

The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).

For example, this patch had to be created because two headers were
called the same way: e0ea0928 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3 ("drivers: add tzc380 support").

This problem was introduced in commit 4ecca339

 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.

Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.

Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: Ib7c2529b85bb5930d44907edfc8ead13d3b1ef4d
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

SPM needs to map a number of regions on behalf of the secure partition.
Previously, it used to get a list of them from platform code using the
plat_get_secure_partition_mmap() API. Now it gets them from the resource
description structure.

The SPM<->SP shared buffer is mapped dynamically at EL3. This buffer is
used to pass information between SPM and SP, so it must be mapped at EL3
as well in order to be used by SPM.

Dynamic translation tables have been enabled when the Trusted Firmware
is compiled with SPM support.

Change-Id: I64ad335e931661812a0a60558e60372e1e5e6b72
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Load SP and RD from package instead of relying on RD being already
loaded in memory and the SP being loaded as a BL32 image.

Change-Id: I18d4fbf4597656c6a7e878e1d7c01a8a324f3f8a
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: Iec265dc85d44f35048d1fbcfbe55960d45570027
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Register a priority level, PLAT_SP_PRI, for secure partition with EL3
exception handling framework(ehf) module.

The secure partition manager(SPM) would raise the core's priority to
PLAT_SP_PRI before entering the secure partition, to protect the core
from getting interrupted while in secure partition.

Change-Id: I686897f052a4371e0efa9b929c07d3ad77249e95
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>

Change-Id: I2419416fadfcdf64da8b7690a348007591c4edf3
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I33eaee8e7c983b3042635a448cb8d689ea4e3a12
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: Ica944acc474a099219d50b041cfaeabd4f3d362f
Signed-off-by: Sathees Balya <sathees.balya@arm.com>

This file is shared between FVP and all CSS platforms. While it may be
true that some definitions can be common, it doesn't make sense
conceptually. For example, the stack size depends on the platform and so
does the SRAM size.

After removing them, there are not enough common definitions to justify
having this header, so the other definitions have been moved to the
platform_def.h of FVP, board_css_def.h and arm_def.h.

Change-Id: Ifbf4b017227f9dfefa1a430f67d7d6baae6a4ba1
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This option makes it hard to optimize the memory definitions of all Arm
platforms because any change in the common defines must work in all of
them. The best thing to do is to remove it and move the definition to
each platform's header.

FVP, SGI and SGM were using the definitions in board_arm_def.h. The
definitions have been copied to each platform's platform_def.h. Juno
was already using the ones in platform_def.h, so there have been no
changes.

Change-Id: I9aecd11bbc72a3d0d7aad1ef9934d8df21dcfaf2
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

- Remove references to removed build options.
- Remove support for legacy GIC driver.
- Remove support for LOAD_IMAGE_V2=0.

Change-Id: I72f8c05620bdf4a682765e6e53e2c04ca749a3d5
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The SGI platforms need to allocate memory for CPER buffers. These
platform buffers would be placed between the shared reserved memory
and the per cpu stack memory, thus the need to redefine stack base
pointer for these platforms. This patch allows each board in ARM
platform to define the PLAT_SP_IMAGE_STACK_BASE.

Change-Id: Ib5465448b860ab7ab0f645f7cb278a67acce7be9
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>

Previously mem_protect used to be only supported from BL2. This is not
helpful in the case when ARM TF-A BL2 is not used. This patch demonstrates
mem_protect from el3_runtime firmware on ARM Platforms specifically
when RESET_TO_BL31 or RESET_TO_SP_MIN flag is set as BL2 may be absent
in these cases. The Non secure DRAM is dynamically mapped into EL3 mmap
tables temporarily and then the protected regions are then cleared. This
avoids the need to map the non secure DRAM permanently to BL31/sp_min.

The stack size is also increased, because DYNAMIC_XLAT_TABLES require
a bigger stack.

Change-Id: Ia44c594192ed5c5adc596c0cff2c7cc18c001fde
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

This was correct according to the model specifications , but it seems
that FVP doesn't implement it. It is safer to use the size exposed by
the DTB which is currently used by Linux.

Change-Id: I9aabe3284a50ec2a36ed94966eb7e4ddf37cec3b
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

With this patch, ARM platforms are expected to define the macros
PLAT_ARM_SDEI_PRIVATE_EVENTS and PLAT_ARM_SDEI_SHARED_EVENTS as a list
of private and shared events, respectively. This allows for individual
platforms to define their own events.

Change-Id: I66851fdcbff83fd9568c2777ade9eb12df284b49
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Common code mustn't include ARM platforms headers.

Change-Id: Ib6e4f5a77c2d095e6e8c3ad89c89cb1959cd3043
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

An earlier patch added provision for the platform to provide secure
interrupt properties. ARM platforms already has a list of interrupts
that fall into different secure groups.

This patch defines macros that enumerate interrupt properties in the
same fashion, and points the driver driver data to a list of interrupt
properties rather than list of secure interrupts on ARM platforms.  The
deprecated interrupt list definitions are however retained to support
legacy builds.

Configuration applied to individual interrupts remain unchanged, so no
runtime behaviour change expected.

NOTE: Platforms that use the arm/common function
plat_arm_gic_driver_init() must replace their PLAT_ARM_G1S_IRQS and
PLAT_ARM_G0_IRQS macro definitions with PLAT_ARM_G1S_IRQ_PROPS and
PLAT_ARM_G0_IRQ_PROPS macros respectively, using the provided
INTR_PROP_DESC macro.

Change-Id: I24d643b83e3333753a3ba97d4b6fb71e16bb0952
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Provides GICv3 save/restore feature to arm_system_pwr_domain_resume and
arm_system_pwr_domain_save functions.

Introduce FVP PSCI power level 3 (System level) support. This is solely
done to provide example code on how to use the GICv3 save and restore
helpers.

Also make CSS GICv3 platforms power off the Redistributor on SYSTEM
SUSPEND as its state is saved and restored.

Change-Id: I0d852f3af8824edee1a17c085cf593ddd33a4e77
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Co-Authored-by: Douglas Raillard <douglas.raillard@arm.com>

platform_def.h doesn't need all the definitions in utils.h,
the ones in utils_def.h are enough. This patch is related
to the changes introduced by commit 53d9c9c8

.

Change-Id: I4b2ff237a2d7fe07a7230e0e49b44b3fc2ca8abe
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

Revision C of the Base FVP has the same memory map as earlier revisions,
but has the following differences:

  - Implements CCI550 instead of CCI400,
  - Has a single instantiation of SMMUv3,
  - CPU MPIDs are shifted left by one level, and has MT bit set in them.

The correct interconnect to program is chosen at run time based on the
FVP revision. Therefore, this patch implements FVP functions for
interconnect programming, rather than depending on ARM generic ones. The
macros used have been renamed to reflect this change.

Additionally, this patch initializes SMMUv3 as part of FVP early
platform setup.

New ARM config flags are introduced for feature queries at run time.

Change-Id: Ic7b7f080953a51fceaf62ce7daa6de0573801f09
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

ARM CPUs with multi-threading implementation has more than one
Processing Element in a single physical CPU. Such an implementation will
reflect the following changes in the MPIDR register:

  - The MT bit set;

  - Affinity levels pertaining to cluster and CPUs occupy one level
    higher than in a single-threaded implementation, and the lowest
    affinity level pertains to hardware threads. MPIDR affinity level
    fields essentially appear shifted to left than otherwise.

The FVP port henceforth assumes that both properties above to be
concomitant on a given FVP platform.

To accommodate for varied MPIDR formats at run time, this patch
re-implements the FVP platform-specific functions that translates MPIDR
values to a linear indices, along with required validation. The same
treatment is applied for GICv3 MPIDR hashing function as well.

An FVP-specific build option FVP_MAX_PE_PER_CPU is introduced which
specifies the maximum number of threads implemented per CPU. For
backwards compatibility, its value defaults to 1.

Change-Id: I729b00d3e121d16ce9a03de4f9db36dfac580e3f
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

On ARM platforms before exiting from SP_MIN ensure that
the default console is switched to the runtime serial port.

Change-Id: I0ca0d42cc47e345d56179eac16aa3d6712767c9b
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/



Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

Some header files using the ULL() macro were not directly including
utils.h where the macro definition resides. As a consequence, a linker
script with values using this macro did not see the macro definition
and kept the "ULL(<value>)" call in the preprocessed file, which lead to
link error.

Files using ULL() macro now include utils.h directly.

Change-Id: I433a7f36bd21a156c20e69bc2a2bb406140ebdf9
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

With GCC 6.2 compiler, more C undefined behaviour is being flagged as
warnings, which result in build errors in ARM TF build.

The specific issue that this patch resolves is the use of (1 << 31),
which is predominantly used in case statements, where 1 is represented
as a signed int. When shifted to msb the behaviour is undefined.

The resolution is to specify 1 as an unsigned int using a convenience
macro ULL(). A duplicate macro MAKE_ULL() is replaced.

Fixes ARM-software/tf-issues#438

Change-Id: I08e3053bbcf4c022ee2be33a75bd0056da4073e1
Signed-off-by: David Cunado <david.cunado@arm.com>

Compile option `ARM_BOARD_OPTIMISE_MMAP` has been renamed to
`ARM_BOARD_OPTIMISE_MEM` because it now applies not only to defines
related to the translation tables but to the image size as well.

The defines `PLAT_ARM_MAX_BL1_RW_SIZE`, `PLAT_ARM_MAX_BL2_SIZE` and
`PLAT_ARM_MAX_BL31_SIZE` have been moved to the file board_arm_def.h.
This way, ARM platforms no longer have to set their own values if
`ARM_BOARD_OPTIMISE_MEM=0` and they can specify optimized values
otherwise. The common sizes have been set to the highest values used
for any of the current build configurations.

This is needed because in some build configurations some images are
running out of space. This way there is a common set of values known
to work for all of them and it can be optimized for each particular
platform if needed.

The space reserved for BL2 when `TRUSTED_BOARD_BOOT=0` has been
increased. This is needed because when memory optimisations are
disabled the values for Juno of `PLAT_ARM_MMAP_ENTRIES` and
`MAX_XLAT_TABLES` are higher. If in this situation the code is
compiled in debug mode and with "-O0", the code won't fit.

Change-Id: I70a3d8d3a0b0cad1d6b602c01a7ea334776e718e

This patch adds support to select CCN driver for FVP during build.
A new build option `FVP_INTERCONNECT_DRIVER` is added to allow
selection between the CCI and CCN driver. Currently only the CCN-502
variant is supported on FVP.

The common ARM CCN platform helper file now verifies the cluster
count declared by platform is equal to the number of root node
masters exported by the ARM Standard platform.

Change-Id: I71d7b4785f8925ed499c153b2e9b9925fcefd57a

This patch migrates ARM Standard platforms to the refactored TZC driver.

Change-Id: I2a2f60b645f73e14d8f416740c4551cec87cb1fb