GitLab

This patch adds support for booting EL3 payloads on CSS platforms,
for example Juno. In this scenario, the Trusted Firmware follows
its normal boot flow up to the point where it would normally pass
control to the BL31 image. At this point, it jumps to the EL3
payload entry point address instead.

Before handing over to the EL3 payload, the data SCP writes for AP
at the beginning of the Trusted SRAM is restored, i.e. we zero the
first 128 bytes and restore the SCP Boot configuration. The latter
is saved before transferring the BL30 image to SCP and is restored
just after the transfer (in BL2). The goal is to make it appear that
the EL3 payload is the first piece of software to run on the target.

The BL31 entrypoint info structure is updated to make the primary
CPU jump to the EL3 payload instead of the BL31 image.

The mailbox is populated with the EL3 payload entrypoint address,
which releases the secondary CPUs out of their holding pen (if the
SCP has powered them on). The arm_program_trusted_mailbox() function
has been exported for this purpose.

The TZC-400 configuration in BL2 is simplified: it grants secure
access only to the whole DRAM. Other security initialization is
unchanged.

This alternative boot flow is disabled by default. A new build option
EL3_PAYLOAD_BASE has been introduced to enable it and provide the EL3
payload's entry point address. The build system has been modified
such that BL31 and BL33 are not compiled and/or not put in the FIP in
this case, as those images are not used in this boot flow.

Change-Id: Id2e26fa57988bbc32323a0effd022ab42f5b5077

This patch fixes a compilation issue for platforms that are aligned to ARM
Standard platforms and include the `plat_arm.h` header in their platform port.
The compilation would fail for such a platform because `xlat_tables.h` which
has the definition for `mmap_region_t` is not included in `plat_arm.h`. This
patch fixes this by including `xlat_tables.h` in `plat_arm.h` header.

Fixes ARM-Software/tf-issues#318

Change-Id: I75f990cfb4078b3996fc353c8cd37c9de61d555e

This patch adds the capability to power down at system power domain level
on Juno via the PSCI SYSTEM SUSPEND API. The CSS power management helpers
are modified to add support for power management operations at system
power domain level. A new helper for populating `get_sys_suspend_power_state`
handler in plat_psci_ops is defined. On entering the system suspend state,
the SCP powers down the SYSTOP power domain on the SoC and puts the memory
into retention mode. On wakeup from the power down, the system components
on the CSS will be reinitialized by the platform layer and the PSCI client
is responsible for restoring the context of these system components.

According to PSCI Specification, interrupts targeted to cores in PSCI CPU
SUSPEND should be able to resume it. On Juno, when the system power domain
is suspended, the GIC is also powered down. The SCP resumes the final core
to be suspend when an external wake-up event is received. But the other
cores cannot be woken up by a targeted interrupt, because GIC doesn't
forward these interrupts to the SCP. Due to this hardware limitation,
we down-grade PSCI CPU SUSPEND requests targeted to the system power domain
level to cluster power domain level in `juno_validate_power_state()`
and the CSS default `plat_arm_psci_ops` is overridden in juno_pm.c.

A system power domain resume helper `arm_system_pwr_domain_resume()` is
defined for ARM standard platforms which resumes/re-initializes the
system components on wakeup from system suspend. The security setup also
needs to be done on resume from system suspend, which means
`plat_arm_security_setup()` must now be included in the BL3-1 image in
addition to previous BL images if system suspend need to be supported.

Change-Id: Ie293f75f09bad24223af47ab6c6e1268f77bcc47

This patch implements the necessary topology changes for supporting
system power domain on CSS platforms. The definition of PLAT_MAX_PWR_LVL and
PLAT_NUM_PWR_DOMAINS macros are removed from arm_def.h and are made platform
specific. In addition, the `arm_power_domain_tree_desc[]` and
`arm_pm_idle_states[]` are modified to support the system power domain
at level 2. With this patch, even though the power management operations
involving the system power domain will not return any error, the platform
layer will silently ignore any operations to the power domain. The actual
power management support for the system power domain will be added later.

Change-Id: I791867eded5156754fe898f9cdc6bba361e5a379

This patch does the following reorganization to psci power management (PM)
handler setup for ARM standard platform ports :

1. The mailbox programming required during `plat_setup_psci_ops()` is identical
   for all ARM platforms. Hence the implementation of this API is now moved
   to the common `arm_pm.c` file. Each ARM platform now must define the
   PLAT_ARM_TRUSTED_MAILBOX_BASE macro, which in current platforms is the same
   as ARM_SHARED_RAM_BASE.

2. The PSCI PM handler callback structure, `plat_psci_ops`, must now be
   exported via `plat_arm_psci_pm_ops`. This allows the common implementation
   of `plat_setup_psci_ops()` to return a platform specific `plat_psci_ops`.
   In the case of CSS platforms, a default weak implementation of the same is
   provided in `css_pm.c` which can be overridden by each CSS platform.

3. For CSS platforms, the PSCI PM handlers defined in `css_pm.c` are now
   made library functions and a new header file `css_pm.h` is added to export
   these generic PM handlers. This allows the platform to reuse the
   adequate CSS PM handlers and redefine others which need to be customized
   when overriding the default `plat_arm_psci_pm_ops` in `css_pm.c`.

Change-Id: I277910f609e023ee5d5ff0129a80ecfce4356ede

This patch updates ARM platform ports to use the new unified bakery locks
API. The caller does not have to use a different bakery lock API depending upon
the value of the USE_COHERENT_MEM build option.

NOTE: THIS PATCH CAN BE USED AS A REFERENCE TO UPDATE OTHER PLATFORM PORTS.

Change-Id: I1b26afc7c9a9808a6040eb22f603d30192251da7

On Juno and FVP platforms, the Non-Secure System timer corresponds
to frame 1. However, this is a platform-specific decision and it
shouldn't be hard-coded. Hence, this patch introduces
PLAT_ARM_NSTIMER_FRAME_ID which should be used by all ARM platforms
to specify the correct non-secure timer frame.

Change-Id: I6c3a905d7d89200a2f58c20ce5d1e1d166832bba

This patch replaces the `ARM_TZC_BASE` constant with `PLAT_ARM_TZC_BASE` to
support different TrustZone Controller base addresses across ARM platforms.

Change-Id: Ie4e1c7600fd7a5875323c7cc35e067de0c6ef6dd

ARM TF configures all interrupts as non-secure except those which
are present in irq_sec_array. This patch updates the irq_sec_array
with the missing secure interrupts for ARM platforms.

It also updates the documentation to be inline with the latest
implementation.

Fixes ARM-software/tf-issues#312

Change-Id: I39956c56a319086e3929d1fa89030b4ec4b01fcc

This patch implements the platform power managment handler to verify
non secure entrypoint for ARM platforms. The handler ensures that the
entry point specified by the normal world during CPU_SUSPEND, CPU_ON
or SYSTEM_SUSPEND PSCI API is a valid address within the non secure
DRAM.

Change-Id: I4795452df99f67a24682b22f0e0967175c1de429

Since there is a unique warm reset entry point, the FVP and Juno
port can use a single mailbox instead of maintaining one per core.
The mailbox gets programmed only once when plat_setup_psci_ops()
is invoked during PSCI initialization. This means mailbox is not
zeroed out during wakeup.

Change-Id: Ieba032a90b43650f970f197340ebb0ce5548d432

This patch adds support to the Juno and FVP ports for composite power states
with both the original and extended state-id power-state formats. Both the
platform ports use the recommended state-id encoding as specified in
Section 6.5 of the PSCI specification (ARM DEN 0022C). The platform build flag
ARM_RECOM_STATE_ID_ENC is used to include this support.

By default, to maintain backwards compatibility, the original power state
parameter format is used and the state-id field is expected to be zero.

Change-Id: Ie721b961957eaecaca5bf417a30952fe0627ef10

This patch migrates ARM reference platforms, Juno and FVP, to the new platform
API mandated by the new PSCI power domain topology and composite power state
frameworks. The platform specific makefiles now exports the build flag
ENABLE_PLAT_COMPAT=0 to disable the platform compatibility layer.

Change-Id: I3040ed7cce446fc66facaee9c67cb54a8cd7ca29

If Trusted Firmware is built with optimizations disabled (-O0), the
linker throws the following error:

    undefined reference to 'xxx'

Where 'xxx' is a raw inline function defined in a header file. The
reason is that, with optimizations disabled, GCC may decide to skip
the inlining. If that is the case, an external definition to the
compilation unit must be provided. Because no external definition
is present, the linker throws the error.

This patch fixes the problem by declaring the following inline
functions static, so the internal definition is used:

    inline void soc_css_security_setup(void)
    inline const arm_config_t *get_arm_config(void)

Change-Id: Id650d6be1b1396bdb48af1ac8a4c7900d212e95f

This patch changes the type of the base address parameter in the
ARM device driver APIs to uintptr_t (GIC, CCI, TZC400, PL011). The
uintptr_t type allows coverage of the whole memory space and to
perform arithmetic operations on the addresses. ARM platform code
has also been updated to use uintptr_t as GIC base address in the
configuration.

Fixes ARM-software/tf-issues#214

Change-Id: I1b87daedadcc8b63e8f113477979675e07d788f1

This patch modifies the Trusted Board Boot implementation to use
the new authentication framework, making use of the authentication
module, the cryto module and the image parser module to
authenticate the images in the Chain of Trust.

A new function 'load_auth_image()' has been implemented. When TBB
is enabled, this function will call the authentication module to
authenticate parent images following the CoT up to the root of
trust to finally load and authenticate the requested image.

The platform is responsible for picking up the right makefiles to
build the corresponding cryptographic and image parser libraries.
ARM platforms use the mbedTLS based libraries.

The platform may also specify what key algorithm should be used
to sign the certificates. This is done by declaring the 'KEY_ALG'
variable in the platform makefile. FVP and Juno use ECDSA keys.

On ARM platforms, BL2 and BL1-RW regions have been increased 4KB
each to accommodate the ECDSA code.

REMOVED BUILD OPTIONS:

  * 'AUTH_MOD'

Change-Id: I47d436589fc213a39edf5f5297bbd955f15ae867

This patch adds a CoT based on the Trusted Board Boot Requirements
document*. The CoT consists of an array of authentication image
descriptors indexed by the image identifiers.

A new header file with TBBR image identifiers has been added.
Platforms that use the TBBR (i.e. ARM platforms) may reuse these
definitions as part of their platform porting.

PLATFORM PORT - IMPORTANT:

Default image IDs have been removed from the platform common
definitions file (common_def.h). As a consequence, platforms that
used those common definitons must now either include the IDs
provided by the TBBR header file or define their own IDs.

*The NVCounter authentication method has not been implemented yet.

Change-Id: I7c4d591863ef53bb0cd4ce6c52a60b06fa0102d5

This patch extends the platform port by adding an API that returns
either the Root of Trust public key (ROTPK) or its hash. This is
usually stored in ROM or eFUSE memory. The ROTPK returned must be
encoded in DER format according to the following ASN.1 structure:

    SubjectPublicKeyInfo  ::=  SEQUENCE  {
        algorithm           AlgorithmIdentifier,
        subjectPublicKey    BIT STRING
    }

In case the platform returns a hash of the key:

    DigestInfo  ::= SEQUENCE {
        digestAlgorithm     AlgorithmIdentifier,
        keyDigest           OCTET STRING
    }

An implementation for ARM development platforms is provided in this
patch. When TBB is enabled, the ROTPK hash location must be specified
using the build option 'ARM_ROTPK_LOCATION'. Available options are:

    - 'regs' : return the ROTPK hash stored in the Trusted
      root-key storage registers.

    - 'devel_rsa' : return a ROTPK hash embedded in the BL1 and
      BL2 binaries. This hash has been obtained from the development
      RSA public key located in 'plat/arm/board/common/rotpk'.

On FVP, the number of MMU tables has been increased to map and
access the ROTPK registers.

A new file 'board_common.mk' has been added to improve code sharing
in the ARM develelopment platforms.

Change-Id: Ib25862e5507d1438da10773e62bd338da8f360bf

The Trusted firmware code identifies BL images by name. The platform
port defines a name for each image e.g. the IO framework uses this
mechanism in the platform function plat_get_image_source(). For
a given image name, it returns the handle to the image file which
involves comparing images names. In addition, if the image is
packaged in a FIP, a name comparison is required to find the UUID
for the image. This method is not optimal.

This patch changes the interface between the generic and platform
code with regard to identifying images. The platform port must now
allocate a unique number (ID) for every image. The generic code will
use the image ID instead of the name to access its attributes.

As a result, the plat_get_image_source() function now takes an image
ID as an input parameter. The organisation of data structures within
the IO framework has been rationalised to use an image ID as an index
into an array which contains attributes of the image such as UUID and
name. This prevents the name comparisons.

A new type 'io_uuid_spec_t' has been introduced in the IO framework
to specify images identified by UUID (i.e. when the image is contained
in a FIP file). There is no longer need to maintain a look-up table
[iname_name --> uuid] in the io_fip driver code.

Because image names are no longer mandatory in the platform port, the
debug messages in the generic code will show the image identifier
instead of the file name. The platforms that support semihosting to
load images (i.e. FVP) must provide the file names as definitions
private to the platform.

The ARM platform ports and documentation have been updated accordingly.
All ARM platforms reuse the image IDs defined in the platform common
code. These IDs will be used to access other attributes of an image in
subsequent patches.

IMPORTANT: applying this patch breaks compatibility for platforms that
use TF BL1 or BL2 images or the image loading code. The platform port
must be updated to match the new interface.

Change-Id: I9c1b04cb1a0684c6ee65dee66146dd6731751ea5

Add SP804 delay timer support to the FVP BSP.

This commit simply provides the 3 constants needed by the SP804
delay timer driver and calls sp804_timer_init() in
bl2_platform_setup(). The BSP does not currently use the delay
timer functions.

Note that the FVP SP804 is a normal world accessible peripheral
and should not be used by the secure world after transition
to the normal world.

Change-Id: I5f91d2ac9eb336fd81943b3bb388860dfb5f2b39
Co-authored-by: Dan Handley <dan.handley@arm.com>

For CSS based platforms, the constants MHU_SECURE_BASE and
MHU_SECURE_SIZE used to define the extents of the Trusted Mailboxes.
As such, they were misnamed because the mailboxes are completely
unrelated to the MHU hardware.

This patch removes the MHU_SECURE_BASE and MHU_SECURE_SIZE #defines.
The address of the Trusted Mailboxes is now relative to the base of
the Trusted SRAM.

This patch also introduces a new constant, SCP_COM_SHARED_MEM_BASE,
which is the address of the first memory region used for communication
between AP and SCP. This is used by the BOM and SCPI protocols.

Change-Id: Ib200f057b19816bf05e834d111271c3ea777291f

Add a comment explaining what the SCP boot configuration information
is on CSS based platforms like Juno. Also express its address
relatively to the base of the Trusted SRAM rather than hard-coding it.

Change-Id: I82cf708a284c8b8212933074ea8c37bdf48b403b

This patch fixes the incorrect bit width used to extract the primary
cpu id from `ap_data` exported by scp at SCP_BOOT_CFG_ADDR in
platform_is_primary_cpu().

Change-Id: I14abb361685f31164ecce0755fc1a145903b27aa

This major change pulls out the common functionality from the
FVP and Juno platform ports into the following categories:

*   (include/)plat/common. Common platform porting functionality that
typically may be used by all platforms.

*   (include/)plat/arm/common. Common platform porting functionality
that may be used by all ARM standard platforms. This includes all
ARM development platforms like FVP and Juno but may also include
non-ARM-owned platforms.

*   (include/)plat/arm/board/common. Common platform porting
functionality for ARM development platforms at the board
(off SoC) level.

*   (include/)plat/arm/css/common. Common platform porting
functionality at the ARM Compute SubSystem (CSS) level. Juno
is an example of a CSS-based platform.

*   (include/)plat/arm/soc/common. Common platform porting
functionality at the ARM SoC level, which is not already defined
at the ARM CSS level.

No guarantees are made about the backward compatibility of
functionality provided in (include/)plat/arm.

Also remove any unnecessary variation between the ARM development
platform ports, including:

*   Unify the way BL2 passes `bl31_params_t` to BL3-1. Use the
Juno implementation, which copies the information from BL2 memory
instead of expecting it to persist in shared memory.

*   Unify the TZC configuration. There is no need to add a region
for SCP in Juno; it's enough to simply not allow any access to
this reserved region. Also set region 0 to provide no access by
default instead of assuming this is the case.

*   Unify the number of memory map regions required for ARM
development platforms, although the actual ranges mapped for each
platform may be different. For the FVP port, this reduces the
mapped peripheral address space.

These latter changes will only be observed when the platform ports
are migrated to use the new common platform code in subsequent
patches.

Change-Id: Id9c269dd3dc6e74533d0e5116fdd826d53946dc8