GitLab

As per the GICv3 specification, to power down a processor using GICv3
and allow automatic power-on if an interrupt must be sent to a processor,
software must set Enable to zero for all interrupt groups(by writing to
GICC_CTLR or ICC_IGRPEN{0,1}_EL1/3 as appropriate.

Also, NonSecure EL1 software may not be aware of the CPU power state
details and fail to choose right states that require quiescing the CPU
interface. So it's preferred that the PSCI implementation handles it as
it is fully aware of the CPU power states.

This patch adds disabling of Group1 NonSecure interrupts during processor
power down along with Group0 and Group1 Secure interrupts so that all the
interrupt groups are handled at once as per specification.

Change-Id: Ib564d773c9c4c41f2ca9471451c030e3de75e641

This patch fixes the offset of GICD_IROUTER register defined in gicv3.h.
Although the GICv3 documention mentions that the offset for this register
is 0x6100-0x7FD8, the offset calculation for an interrupt id `n` is :

   0x6000 + 8n, where n >= 32

This requires the offset for GICD_IROUTER to be defined as 0x6000.

Fixes ARM-software/tf-issues#410

Change-Id: If9e91e30d946afe7f1f60fea4f065c7567093fa8

This patch reworks type usage in generic code, drivers and ARM platform files
to make it more portable. The major changes done with respect to
type usage are as listed below:

* Use uintptr_t for storing address instead of uint64_t or unsigned long.
* Review usage of unsigned long as it can no longer be assumed to be 64 bit.
* Use u_register_t for register values whose width varies depending on
  whether AArch64 or AArch32.
* Use generic C types where-ever possible.

In addition to the above changes, this patch also modifies format specifiers
in print invocations so that they are AArch64/AArch32 agnostic. Only files
related to upcoming feature development have been reworked.

Change-Id: I9f8c78347c5a52ba7027ff389791f1dad63ee5f8

This patch moves the private GIC common accessors from `gic_common.h` to
a new private header file `gic_common_private.h`. This patch also adds
additional comments to GIC register accessors to highlight the fact
that some of them access register values that correspond to multiple
interrupt IDs. The convention used is that the `set`, `get` and `clr`
accessors access and modify the values corresponding to a single interrupt
ID whereas the `read` and `write` GIC register accessors access the raw
GIC registers and it could correspond to multiple interrupt IDs depending
on the register accessed.

Change-Id: I2643ecb2533f01e3d3219fcedfb5f80c120622f9

The code to set the interrupt priority for secure interrupts in the
new GICv2 and GICv3 drivers is incorrect. The setup code to configure
interrupt priorities of secure interrupts, one interrupt at a time, used
gicd_write_ipriorityr()/gicr_write_ipriority() function affecting
4 interrupts at a time. This bug did not manifest itself because all the
secure interrupts were configured to the highest secure priority(0) during
cold boot and the adjacent non secure interrupt priority would be configured
later by the normal world. This patch introduces new accessors,
gicd_set_ipriorityr() and gicr_set_ipriorityr(), for configuring priority
one interrupt at a time and fixes the the setup code to use the new
accessors.

Fixes ARM-software/tf-issues#344

Change-Id: I470fd74d2b7fce7058b55d83f604be05a27e1341

This patch renames the GICv3 interrupt group macros from
INT_TYPE_G0, INT_TYPE_G1S and INT_TYPE_G1NS to INTR_GROUP0,
INTR_GROUP1S and INTR_GROUP1NS respectively.

Change-Id: I40c66f589ce6234fa42205adcd91f7d6ad8f33d4

This patch adds a driver for ARM GICv3 systems that need to run software
stacks where affinity routing is enabled across all privileged exception
levels for both security states. This driver is a partial implementation
of the ARM Generic Interrupt Controller Architecture Specification, GIC
architecture version 3.0 and version 4.0 (ARM IHI 0069A). The driver does
not cater for legacy support of interrupts and asymmetric configurations.

The existing GIC driver has been preserved unchanged. The common code for
GICv2 and GICv3 systems has been refactored into a new file,
`drivers/arm/gic/common/gic_common.c`. The corresponding header is in
`include/drivers/arm/gic_common.h`.

The driver interface is implemented in `drivers/arm/gic/v3/gicv3_main.c`.
The corresponding header is in `include/drivers/arm/gicv3.h`. Helper
functions are implemented in `drivers/arm/gic/v3/arm_gicv3_helpers.c`
and are accessible through the `drivers/arm/gic/v3/gicv3_private.h`
header.

Change-Id: I8c3c834a1d049d05b776b4dcb76b18ccb927444a