GitLab

Now that there is plenty of space (32 KiB) available for NOBITS
sections, we can afford using an entire page for coherent memory. In
fact, because it simplifies the code, this is a beneficial change for
loaded image (.text) size, where we are still close to the size limit.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I0b899dabcb162015c63b0e4aed0869569c889ed9

Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Ia2f69e26e34462e113bc2cad4dcb923e20b8fb95

This frees up space in SRAM A2 that will be used by the SCP firmware and
SCPI shared memory.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I8ce035257451e2d142666fe0cd045e59d4d57b35

Chip ID checking and poweroff work just like they did before.
Regulators are now enabled just like on A64/H5.

This changes the signatures of the low-level register read/write
functions to match the interface expected by the common driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I14d63d171a094fa1375904928270fa3e21761646

The action of last resort isn't going to change between SoCs. This moves
that code back to the PSCI implementation, where it more obviously
matches the code in sunxi_system_reset().

The two error messages say essentially the same thing anyway.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I62ac35fdb5ed78a016e9b18281416f1dcea38a4a

The clock must be running for the module to be reset.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Ic8fafc946f3a1a697174b91288e357ffa033ab9a

The current range check for the offset is wrong: it is counting bytes,
while indexing an array of uint32_t. Since the offset is always zero,
the parameter is unnecessary. Instead of adding more code to fix the
check, remove the parameter to avoid the problem entirely.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Iadfc7d027155adc754e017b3462233ce9a1d64f6

The new API becomes the default one.

Change-Id: Ic1d602da3dff4f4ebbcc158b885295c902a24fec
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>

As all Allwinner platforms are single-cluster A53 chips, we can disable
support for newer, unsupported architecture extensions. We can also
avoid some cache maintenance code, since no platform-specific setup is
required to enable coherency.

These changes reduce the size of .text on a default build with GCC 9.1
enough that .vectors again fits in the second half of a page, instead
of requiring its own page.

This commit was boot-tested on the Pinebook.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Ib90454ef0c798d5e714b7780c585be0b1ed49c6d

Some Allwinner H6 has a broken watchdog that doesn't
make the soc reboot.

Use the R_WATCHDOG instead.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Change-Id: Ie95cc30a80ed517b60b30d6bc2e655a1b53f18ba

Convert them to take an mpidr instead of a (cluster, core) pair. This
simplifies all of the call sites, and actually makes the functions a bit
smaller.
Signed-off-by: Samuel Holland <samuel@sholland.org>

This maximizes the amount of data protected by the MMU.
Signed-off-by: Samuel Holland <samuel@sholland.org>

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}

The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).

For example, this patch had to be created because two headers were
called the same way: e0ea0928 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3 ("drivers: add tzc380 support").

This problem was introduced in commit 4ecca339

 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.

Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.

Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch makes the build system link the console framework code by
default, like it already does with other common libraries (e.g. cache
helpers). This should not make a difference in practice since TF is
linked with --gc-sections, so the linker will garbage collect all
functions and data that are not referenced by any other code. Thus, if a
platform doesn't want to include console code for size reasons and
doesn't make any references to console functions, the code will not be
included in the final binary.

To avoid compatibility issues with older platform ports, only make this
change for the MULTI_CONSOLE_API.

Change-Id: I153a9dbe680d57aadb860d1c829759ba701130d3
Signed-off-by: Julius Werner <jwerner@chromium.org>

The legacy Allwinner ATF port used to setup some clocks, and U-Boot is
still relying on this. We don't need to setup the full set, as the SPL
is doing most of it, but it misses one clock (AHB2) and programs another
(AHB1) to quite conservative values.

Fix this up during the platform setup to improve USB and Ethernet
performance, iperf values go up by 31% in my setup with that patch.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

All identifiers, regardless of use, that start with two underscores are
reserved. This means they can't be used in header guards.

The style that this project is now to use the full name of the file in
capital letters followed by 'H'. For example, for a file called
"uart_example.h", the header guard is UART_EXAMPLE_H.

The exceptions are files that are imported from other projects:

- CryptoCell driver
- dt-bindings folders
- zlib headers

Change-Id: I50561bf6c88b491ec440d0c8385c74650f3c106e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

PSCI requires a core to turn itself off, which we can't do properly by
just executing an algorithm on that very core. As a consequence we just
put a core into WFI on CPU_OFF right now.
To fix this let's task the "arisc" management processor (an OpenRISC
core) with that task of asserting reset and turning off the core's power
domain. We use a handcrafted sequence of OpenRISC instructions to
achieve this, and hand this data over to the new sunxi_execute_arisc_code()
routine.
The commented source code for this routine is provided in a separate file,
but the ATF code contains the already encoded instructions as data.
The H6 uses the same algorithm, but differs in the MMIO addresses, so
provide a SoC (family) specific copy of that code.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The more recent Allwinner SoCs contain an OpenRISC management
controller (called arisc or CPUS), which shares the bus with the ARM cores,
but runs on a separate power domain. This is meant to handle power
management with the ARM cores off.
There are efforts to run sophisticated firmware on that core
(communicating via SCPI with the ARM world), but for now can use it for
the rather simple task of helping to turn the ARM cores off. As this
cannot be done by ARM code itself (because execution stops at the
first of the three required steps), we can offload some instructions to
this management processor.
This introduces a helper function to hand over a bunch of instructions
and triggers execution. We introduce a bakery lock to avoid two cores
trying to use that (single) arisc core. The arisc code is expected to
put itself into reset after is has finished execution.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

For Allwinner boards we now use some heuritistics to find a preloaded
.dtb file.

Pass this address on to the PMIC setup routine, so that it can use the
information contained therein to setup some initial power rails.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The initial PMIC setup for the Allwinner platform is quite board
specific, and used to be guarded by reading the .dtb stub *name* from the
SPL image in the legacy ATF port. This doesn't scale particularly well,
and requires constant maintainance.
Instead having the actual .dtb available would be much better, as the PMIC
setup requirements could be read from there directly.
The only available BL33 for Allwinner platforms so far is U-Boot, and
fortunately U-Boot comes with the full featured .dtb, appended to the
end of the U-Boot image.

Introduce some code that scans the beginning of the BL33 image to look
for the load address, which is followed by the image size. Adding those
two values together gives us the end of the image and thus the .dtb
address. Verify that this heuristic is valid by sanitising some values
and checking the DTB magic.

Print out the DTB address and the model name, if specified in the root
node.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

In the H6 platform code there is a routine to do the platform
initialisation of the R_I2C controller. We will need a very similar
setup routine to initialise the RSB controller on the A64.

Move this code to sunxi_common.c and generalise it to support all SoCs
and also to cover the related RSB bus.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Many boards without a dedicated PMIC contain simple regulators, which
can be controlled via GPIO pins.

To later allow turning them off easily, introduce a simple function to
configure a given pin as a GPIO out pin and set it to the desired level.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

So far we have a sunxi_private.h header file in the common code directory.
This holds the prototypes of various functions we share in *common*
code. However we will need some of those in the platform specific code
parts as well, and want to introduce new functions shared across the
whole platform port.

So move the sunxi_private.h file into the common/include directory, so
that it becomes visible to all parts of the platform code.
Fix up the existing #includes and add missing ones, also add the
sunxi_read_soc_id() prototype here.

This will be used in follow up patches.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

In the BL31 platform setup we read the Allwinner SoC ID to identify the
chip and print its name.
In addition to that we will need to differentiate the power setup
between the SoCs, to pass on the SoC ID to the PMIC setup routine.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

We will soon make more use of the Allwinner SoC ID, to differentiate the
platform setup.
Introduce definitions to avoid dealing with magic numbers and make the
code more readable.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

According to the documentation, platforms may choose to trade memory
footprint for performance (and elegancy) by not providing a separately
mapped coherent page.

Since a debug build is getting close to the SRAM size limit already, this
allows us to save about 3.5KB of BSS and have some room for future
enhancements.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

At the moment we map as much of the DRAM into EL3 as possible, however
we actually don't use it. The only exception is the secure DRAM for
BL32 (if that is configured).

To decrease the memory footprint of ATF, we save on some page tables by
reducing the memory mapping to the actually required regions: SRAM, device
MMIO, secure DRAM and U-Boot (to be used later).
This introduces a non-identity mapping for the DRAM regions.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

For the two different platforms we support in the Allwinner port we
mostly rely on header files covering the differences. This leads to the
platform.mk files in the respective directories to be almost identical.

To avoid further divergence and make sure that one platform doesn't
break accidentally, let's create a shared allwinner-common.mk file and
include that from the platform directory.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

At the moment we have two I2C stub drivers (for the Allwinner and the
Marvell platform), which #include the actual .c driver file.
Change this into the more usual design, by renaming and moving the stub
drivers into platform specific header files and including these from the
actual driver file. The platform specific include directories make sure
the driver picks up the right header automatically.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The AXP805 PMIC used with H6 is capable of shutting down the system.

Add support for using it to shut down the system power.

The original placeholder power off code is moved to A64 code, as it's
still TODO to implement PMIC operations for A64.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

As the ATF may need to do some power initialization on Allwinner
platform with AXP PMICs, call the PMIC setup code in BL31.

Stub of PMIC setup code is added, to prevent undefined reference.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

Also change header guards to fix defects of MISRA C-2012 Rule 21.1.

Change-Id: Ied0d4b0e557ef6119ab669d106d2ac5d99620c57
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The H6 is Allwinner's most recent SoC. It shares most peripherals with the
other ARMv8 Allwinner SoCs (A64/H5), but has a completely different memory
map.

Introduce a separate platform target, which includes a different header
file to cater for the address differences. Also add the new build target
to the documentation.

The new ATF platform name is "sun50i_h6".
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

So far we already support booting on two different SoCs, and we will
shortly add a third, so add some code to determine the current SoC type.
This can be later used to runtime detect certain properties.

Also print the SoC name to the console, to give valuable debug information.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

There is nothing we need from the BootROM area, so we also don't need
to map it in EL3.

Remove the mapping and reduce the number of MMAP regions by one.
Reported-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The DRAM controller supports up to 4GB of DRAM, and there are actually
boards out there where we can use at least 3GB of this.

Relax the PSCI entry point check, to be not restricted to 2GB of DRAM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The "#ifdef SUNXI_SPC_BASE" guard was meant to allow the build on SoCs
without a Secure Peripherals Controller, so that we skip that part of
the security setup. But in the current position this will trigger a
warning about an unused variable.

Simply move the guard one line up to cover the variable as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The "INFO" output in sunxi_cpu_ops.c is quite verbose, so make this more
obvious by changing the log level to "VERBOSE" and so avoiding it to
be printed in a normal (even debug) build.
Reported-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Some code in sunxi_common.c requires symbols defined in sunxi_private.h,
so add the header to that file.
It was included via another header before, but let's make this explicit.
Reported-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

This patch is an attempt to run Trusted OS (OP-TEE OS being one of them) along
side BL31 image.

ATF supports multiple SPD's that can take dispatcher name (opteed for OP-TEE OS)
as an input using the 'SPD=<dispatcher name>' option during bl31 build.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>