GitLab

RSB is faster and more efficient, and it has a simpler driver. As long
as the PMIC is returned to I2C mode after use, the rich OS can later use
either bus.

Change-Id: I0c5f32e88a090c8c5cccb81bd24596b301ab9da7
Signed-off-by: Samuel Holland <samuel@sholland.org>

The base address for both the GPIO and the clock unit of the H6 memory map
have been typo-ed. Fix them to match the Linux DT and the manual.

The H6 code use neither of them, so this doesn't change or fix anything
in the real world, but should be corrected anyway.

The issue was found and reported by Github user "armlabs".

Change-Id: Ic6fdfb732ce1cfc54cbb927718035624a06a9e08
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The ARISC vector area consists of 0x4000 bytes before the beginning of
usable SRAM. Still, it is technically a part of SRAM A2, so include it
in the memory definition. This avoids the confusing practice of
subtracting from the beginning of the SRAM region when referencing the
ARISC vectors.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Iae89e01aeab93560159562692e03e88306e2a1bf

Chip ID checking and poweroff work just like they did before.
Regulators are now enabled just like on A64/H5.

This changes the signatures of the low-level register read/write
functions to match the interface expected by the common driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I14d63d171a094fa1375904928270fa3e21761646

These are used by the PMIC setup code, which runs during BL31
initialization, and the PSCI shutdown code, also a part of BL31.
They can't be needed before BL31, or it wouldn't be possible to boot.
Allwinner platforms don't generally build anything but BL31 anyway, but
this change improves clarity and consistency with allwinner-common.mk.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I24f1d9ca8b4256e44badf5218d04d8690082babf

The action of last resort isn't going to change between SoCs. This moves
that code back to the PSCI implementation, where it more obviously
matches the code in sunxi_system_reset().

The two error messages say essentially the same thing anyway.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I62ac35fdb5ed78a016e9b18281416f1dcea38a4a

- Check the return value from sunxi_init_platform_r_twi().
- Print the PMIC banner before doing anything that might fail.
- Remove double prefixes in error messages.
- Consistently omit the trailing period.
- No need to print the unknown SoC's ID, since we already did that
  earlier in bl31_platform_setup().
- On the other hand, do print the ID of the unknown PMIC.
- Try to keep the messages concise, as the large string size in these
  files was causing the firmware to spill into the next page.
- Downgrade the banner from NOTICE to INFO. It's purely informational,
  and people should be using debug builds on untested hardware anyway.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Ib909408a5fdaebe05470fbce48d245dd0bf040eb

Ensure that the default (zero) value represents the case where we take
no action. Previously, if a PLAT=sun50i_a64 build was booted on an
unknown SoC ID, it would be treated as an H5 at shutdown.

This removes some duplicate code and fixes error propagation on H6.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I4e51d8a43a56eccb0d8088593cb9908e52e782bc

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}

The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).

For example, this patch had to be created because two headers were
called the same way: e0ea0928 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3 ("drivers: add tzc380 support").

This problem was introduced in commit 4ecca339

 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.

Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.

Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

All identifiers, regardless of use, that start with two underscores are
reserved. This means they can't be used in header guards.

The style that this project is now to use the full name of the file in
capital letters followed by 'H'. For example, for a file called
"uart_example.h", the header guard is UART_EXAMPLE_H.

The exceptions are files that are imported from other projects:

- CryptoCell driver
- dt-bindings folders
- zlib headers

Change-Id: I50561bf6c88b491ec440d0c8385c74650f3c106e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

PSCI requires a core to turn itself off, which we can't do properly by
just executing an algorithm on that very core. As a consequence we just
put a core into WFI on CPU_OFF right now.
To fix this let's task the "arisc" management processor (an OpenRISC
core) with that task of asserting reset and turning off the core's power
domain. We use a handcrafted sequence of OpenRISC instructions to
achieve this, and hand this data over to the new sunxi_execute_arisc_code()
routine.
The commented source code for this routine is provided in a separate file,
but the ATF code contains the already encoded instructions as data.
The H6 uses the same algorithm, but differs in the MMIO addresses, so
provide a SoC (family) specific copy of that code.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

For Allwinner boards we now use some heuritistics to find a preloaded
.dtb file.

Pass this address on to the PMIC setup routine, so that it can use the
information contained therein to setup some initial power rails.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

In the H6 platform code there is a routine to do the platform
initialisation of the R_I2C controller. We will need a very similar
setup routine to initialise the RSB controller on the A64.

Move this code to sunxi_common.c and generalise it to support all SoCs
and also to cover the related RSB bus.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

So far we have a sunxi_private.h header file in the common code directory.
This holds the prototypes of various functions we share in *common*
code. However we will need some of those in the platform specific code
parts as well, and want to introduce new functions shared across the
whole platform port.

So move the sunxi_private.h file into the common/include directory, so
that it becomes visible to all parts of the platform code.
Fix up the existing #includes and add missing ones, also add the
sunxi_read_soc_id() prototype here.

This will be used in follow up patches.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

In the BL31 platform setup we read the Allwinner SoC ID to identify the
chip and print its name.
In addition to that we will need to differentiate the power setup
between the SoCs, to pass on the SoC ID to the PMIC setup routine.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The SRAM in the Allwinner H6 SoC starts at 0x2000, with the last part
ending at 0x117fff (although with gaps in between).
So SUNXI_SRAM_SIZE should be 0xf8000, not 0x98000.

Fix this to map the arisc exception vector area, which we will need
shortly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

At the moment we map as much of the DRAM into EL3 as possible, however
we actually don't use it. The only exception is the secure DRAM for
BL32 (if that is configured).

To decrease the memory footprint of ATF, we save on some page tables by
reducing the memory mapping to the actually required regions: SRAM, device
MMIO, secure DRAM and U-Boot (to be used later).
This introduces a non-identity mapping for the DRAM regions.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

For the two different platforms we support in the Allwinner port we
mostly rely on header files covering the differences. This leads to the
platform.mk files in the respective directories to be almost identical.

To avoid further divergence and make sure that one platform doesn't
break accidentally, let's create a shared allwinner-common.mk file and
include that from the platform directory.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Change-Id: I206478597dd9855d3fe1577e7e2c0fe6d2af1cc5
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

At the moment we have two I2C stub drivers (for the Allwinner and the
Marvell platform), which #include the actual .c driver file.
Change this into the more usual design, by renaming and moving the stub
drivers into platform specific header files and including these from the
actual driver file. The platform specific include directories make sure
the driver picks up the right header automatically.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Even though we initialise the platform part and the I2C controller
itself at boot time, we actually only access the bus on power down.
Meanwhile a rich OS might have configured the I2C pins differently or
even disabled the controller.
So repeat the platform setup and controller initialisation just before
we actually access the bus to power off the system. This is safe,
because at this point the rich OS should no longer be running.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Drop the unnecessary check for the I2C pins being already configured as
I2C pins (we actually don't care).
Also avoid resetting *every* peripheral that is covered by the PRCM reset
controller, instead just clear the one line connected to the I2C controller.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The AXP805 PMIC used with H6 is capable of shutting down the system.

Add support for using it to shut down the system power.

The original placeholder power off code is moved to A64 code, as it's
still TODO to implement PMIC operations for A64.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

The OTT reference design of Allwinner H6 SoC uses an X-Powers AXP805
PMIC.

Add initial code for it.

Currently it's only detected.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

As the ATF may need to do some power initialization on Allwinner
platform with AXP PMICs, call the PMIC setup code in BL31.

Stub of PMIC setup code is added, to prevent undefined reference.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

The H6 is Allwinner's most recent SoC. It shares most peripherals with the
other ARMv8 Allwinner SoCs (A64/H5), but has a completely different memory
map.

Introduce a separate platform target, which includes a different header
file to cater for the address differences. Also add the new build target
to the documentation.

The new ATF platform name is "sun50i_h6".
Signed-off-by: Andre Przywara <andre.przywara@arm.com>