GitLab

The base address for second DRAM varies across different platforms.
So allow platforms to define second DRAM by moving Juno/SGM-775 specific
definition of second DRAM base address to Juno/SGM-775 board definition
respectively, SGI/RD specific definition of DRAM 2 base address to SGI
board definition.

Change-Id: I0ecd3a2bd600b6c7019c7f06f8c452952bd07cae
Signed-off-by: Suyash Pathak <suyash.pathak@arm.com>

A TZC400 can have upto 4 filters and the number of filters instantiated
within a TZC400 is platform dependent. So allow platforms to define the
value of PLAT_ARM_TZC_FILTERS by moving the existing Juno specific
definition of PLAT_ARM_TZC_FILTERS to Juno board definitions.

Change-Id: I67a63d7336595bbfdce3163f9a9473e15e266f40
Signed-off-by: Suyash Pathak <suyash.pathak@arm.com>

On systems that have multiple platform components that can interpret the
SCMI messages, there is a need to support multiple SCMI channels (one
each to those platform components). Extend the existing SCMI interface
that currently supports only a single SCMI channel to support multiple
SCMI channels.

Change-Id: Ice4062475b903aef3b5e5bc37df364c9778a62c5
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

In order to allow the MHUv2 driver to be usable with multiple MHUv2
controllers, use the base address of the controller from the platform
information instead of the MHUV2_BASE_ADDR macro.

Change-Id: I4dbab87b929fb0568935e6c8b339ce67937f8cd1
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

ROMLIB extract functions code from BL images to put them inside ROM.
This has for effect to reduce the size of the BL images.

This patch take this size reduction into consideration to optimize the
memory layout of BL2.
A new "PLAT_ARM_BL2_ROMLIB_OPTIMIZATION" macro is defined and used to
reduce "PLAT_ARM_MAX_BL2_SIZE". This allows to remove the gap between
BL1 and BL2 when ROMLIB is used and provides more room for BL31.

The current memory gain is 0x6000 for fvp and 0x8000 for juno.

Change-Id: I71c2c2c63b57bce5b22a125efaefc486ff3e87be
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

NOTE: AARCH32/AARCH64 macros are now deprecated in favor of __aarch64__.

All common C compilers pre-define the same macros to signal which
architecture the code is being compiled for: __arm__ for AArch32 (or
earlier versions) and __aarch64__ for AArch64. There's no need for TF-A
to define its own custom macros for this. In order to unify code with
the export headers (which use __aarch64__ to avoid another dependency),
let's deprecate the AARCH32 and AARCH64 macros and switch the code base
over to the pre-defined standard macro. (Since it is somewhat
unintuitive that __arm__ only means AArch32, let's standardize on only
using __aarch64__.)

Change-Id: Ic77de4b052297d77f38fc95f95f65a8ee70cf200
Signed-off-by: Julius Werner <jwerner@chromium.org>

N1SDP platform supports RDIMMs with ECC capability. To use the ECC
capability, the entire DDR memory space has to be zeroed out before
enabling the ECC bits in DMC620. Zeroing out several gigabytes of
memory from SCP is quite time consuming so functions are added that
zeros out the DDR memory from application processor which is
much faster compared to SCP. BL33 binary cannot be copied to DDR memory
before enabling ECC so this is also done by TF-A from IOFPGA-DDR3
memory to main DDR4 memory after ECC is enabled.

Original PLAT_PHY_ADDR_SPACE_SIZE was limited to 36-bits with which
the entire DDR space cannot be accessed as DRAM2 starts in base
0x8080000000. So these macros are redefined for all ARM platforms.

Change-Id: If09524fb65b421b7a368b1b9fc52c49f2ddb7846
Signed-off-by: Manoj Kumar <manoj.kumar3@arm.com>

MHU doorbell driver requires arm platform specific
macro "PLAT_CSS_MHU_BASE".
Rename it to "PLAT_MHUV2_BASE", so that platforms other than arm
can use generic MHU doorbell driver.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>

The PLAT_XLAT_TABLES_DYNAMIC build option, defined in platform_def.h
in Arm platforms, is checked by several headers, affecting their
behaviour. To avoid issues around the include ordering of the headers,
the definition should be moved to the platform's makefile.

Change-Id: I0e12365c8d66309122e8a20790e1641a4f480a10
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Use full include paths like it is done for common includes.

This cleanup was started in commit d40e0e08283a ("Sanitise includes
across codebase"), but it only cleaned common files and drivers. This
patch does the same to Arm platforms.

Change-Id: If982e6450bbe84dceb56d464e282bcf5d6d9ab9b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

On ARM platforms, the BL2 memory can be overlaid by BL31/BL32. The memory
descriptors describing the list of executable images are created in BL2
R/W memory, which could be possibly corrupted later on by BL31/BL32 due
to overlay. This patch creates a reserved location in SRAM for these
descriptors and are copied over by BL2 before handing over to next BL
image.

Also this patch increases the PLAT_ARM_MAX_BL2_SIZE for juno when TBBR
is enabled.

Fixes ARM-Software/tf-issues#626

Change-Id: I755735706fa702024b4032f51ed4895b3687377f
Signed-off-by: Sathees Balya <sathees.balya@arm.com>

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}

The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).

For example, this patch had to be created because two headers were
called the same way: e0ea0928 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3 ("drivers: add tzc380 support").

This problem was introduced in commit 4ecca339

 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.

Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.

Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The CSS_SYSTEM_PWR_DMN_LVL macro that defines the system power domain
level is fixed at ARM_PWR_LVL2 for all CSS platforms. However, the
system power domain level can be different for CSS platforms that
use multi-threaded CPUs.

So, in preparation towards adding support for platforms that use
multi-threaded CPUs, refactor the definition of CSS_SYSTEM_PWR_DMN_LVL
such that CSS_SYSTEM_PWR_DMN_LVL is uniquely defined for each of the
CSS platform.

Change-Id: Ia837b13f6865e71da01780993c048b45b7f36d85
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>

This patch adds support to build a combined BL1
and ROMLIB binary file with the right page
alignment in Juno. When USE_ROMLIB=1 is set for
Juno, it generates the combined file
bl1_romlib.bin which needs to be used instead of
bl1.bin

Change-Id: I407efbe48d3e522fa6ef855538a9587193cb1919
Signed-off-by: Sathees Balya <sathees.balya@arm.com>

Change-Id: I2419416fadfcdf64da8b7690a348007591c4edf3
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I33eaee8e7c983b3042635a448cb8d689ea4e3a12
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Version 1.4.7 of libfdt is bigger than the current one (1.4.2) and the
current reserved space for BL2 in Juno isn't enough to fit the Trusted
Firmware when compiling with clang or armclang.

Change-Id: I7b73394ca60d17f417773f56dd5b3d54495a45a8
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: Ica944acc474a099219d50b041cfaeabd4f3d362f
Signed-off-by: Sathees Balya <sathees.balya@arm.com>

This file is shared between FVP and all CSS platforms. While it may be
true that some definitions can be common, it doesn't make sense
conceptually. For example, the stack size depends on the platform and so
does the SRAM size.

After removing them, there are not enough common definitions to justify
having this header, so the other definitions have been moved to the
platform_def.h of FVP, board_css_def.h and arm_def.h.

Change-Id: Ifbf4b017227f9dfefa1a430f67d7d6baae6a4ba1
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This option makes it hard to optimize the memory definitions of all Arm
platforms because any change in the common defines must work in all of
them. The best thing to do is to remove it and move the definition to
each platform's header.

FVP, SGI and SGM were using the definitions in board_arm_def.h. The
definitions have been copied to each platform's platform_def.h. Juno
was already using the ones in platform_def.h, so there have been no
changes.

Change-Id: I9aecd11bbc72a3d0d7aad1ef9934d8df21dcfaf2
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: Idb9ba3864d6de3053260724f07172fd32c1523e0
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Change arm_setup_page_tables() to take a variable number of memory
regions. Remove coherent memory region from BL1, BL2 and BL2U as
their coherent memory region doesn't contain anything and
therefore has a size of 0. Add check to ensure this
doesn't change without us knowing.

Change-Id: I790054e3b20b056dda1043a4a67bd7ac2d6a3bc0
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

This patch bumps up the BL1-RW size for Juno and at the same time reduces
the BL2 size when TBB is enabled, TF_MBEDTLS_KEY_ALG=rsa+ecdsa. The BL2
size for this config is reduced as it was observed that the peak memory
usage is only reached when SPD=opteed and the dual rsa+ecdsa support is
not needed for this case.

Change-Id: Ia9009771b5cfd805e9cc75410aabb7db99fc2fbc
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

The patch changes the layout of BL images in memory to enable
more efficient use of available space. Previously BL31 was loaded
with the expectation that BL2 memory would be reclaimed by BL32
loaded in SRAM. But with increasing memory requirements in the
firmware, we can no longer fit BL32 in SRAM anymore which means the
BL2 memory is not reclaimed by any runtime image. Positioning BL2
below BL1-RW and above BL31 means that the BL31 NOBITS can be
overlaid on BL2 and BL1-RW.

This patch also propogates the same memory layout to BL32 for AArch32
mode. The reset addresses for the following configurations are also
changed :
   * When RESET_TO_SP_MIN=1 for BL32 in AArch32 mode
   * When BL2_AT_EL3=1 for BL2

The restriction on BL31 to be only in DRAM when SPM is enabled
is now removed with this change. The update to the firmware design
guide for the BL memory layout is done in the following patch.

Change-Id: Icca438e257abe3e4f5a8215f945b9c3f9fbf29c9
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

SGI-575's NSRAM is neither in the same place nor the same size as Juno's.

Change-Id: Id6d692e9c7e9c1360014bb525eda966ebe29c823
Signed-off-by: Chris Kay <chris.kay@arm.com>

Previously mem_protect used to be only supported from BL2. This is not
helpful in the case when ARM TF-A BL2 is not used. This patch demonstrates
mem_protect from el3_runtime firmware on ARM Platforms specifically
when RESET_TO_BL31 or RESET_TO_SP_MIN flag is set as BL2 may be absent
in these cases. The Non secure DRAM is dynamically mapped into EL3 mmap
tables temporarily and then the protected regions are then cleared. This
avoids the need to map the non secure DRAM permanently to BL31/sp_min.

The stack size is also increased, because DYNAMIC_XLAT_TABLES require
a bigger stack.

Change-Id: Ia44c594192ed5c5adc596c0cff2c7cc18c001fde
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Add TZMP1 support on Juno and increase the BL2 size accordingly due to the
extra data structures to describe the TZC regions and the additional code.
Signed-off-by: Summer Qin <summer.qin@arm.com>

Building TBBR(SPD=opteed) and non-TBBR TF-A images is breaking for
Juno for different configurations listed below:

* Overflow error of 4096 bytes for rsa algorithm.
* Overflow error of 8192 bytes for ecdsa algorithm.
* Overflow error of 4096 bytes for rsa+ecdsa algorithm.
* Overflow error of 4096 bytes for non-TBBR case.

So this patch increments macro PLAT_ARM_MAX_BL2_SIZE for all the above
cases accordingly.

Change-Id: I75ec6c0a718181d34553fe55437f0496f467683f
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>

The patch adds the necessary changes to load HW_CONFIG in BL2 for
ARM Platforms :

1. The load address of HW_CONFIG is specified via the `hw_config_addr`
property in TB_FW_CONFIG is loaded by BL1. The `hw_config_max_size`
property defines the maximum size to be expected for the HW_CONFIG.
The `arm_dyn_cfg_helpers.c` and corresponding header implements
utility functions to parse these DT properties defined.
The `arm_dyn_cfg.c` implements wrappers to these helpers to enable
them to be invoked from ARM platform layer.

2. `HW_CONFIG` is added to the `bl2_mem_params_descs[]` array which is
the list of images to be loaded by BL2.

3. The `libfdt` sources are now included when BL2 is built

4. A new helper `populate_next_bl_params_config()` is introduced in
desc_image_load.c to populate the subsequent executable BL images
with the `hw_config` and the corresponding `fw_config` if available.
The `plat_get_next_bl_params()` API for ARM platforms is modified to
invoke this new helper.

5. The implementation of `bl2_early_platform_setup2()` is modified to
consider `arg0` as well in addition to `arg1` passed from BL1.

6. Bump up the BL2 size for Juno to accommodate the inclusion of libfdt.

Change-Id: I80f1554adec41753e0d179a5237364f04fe13a3f
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

With this patch, ARM platforms are expected to define the macros
PLAT_ARM_SDEI_PRIVATE_EVENTS and PLAT_ARM_SDEI_SHARED_EVENTS as a list
of private and shared events, respectively. This allows for individual
platforms to define their own events.

Change-Id: I66851fdcbff83fd9568c2777ade9eb12df284b49
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

This patch fixes a couple of issues for AArch32 builds on ARM reference
platforms :

1. The arm_def.h previously defined the same BL32_BASE value for AArch64 and
   AArch32 build. Since BL31 is not present in AArch32 mode, this meant that
   the BL31 memory is empty when built for AArch32. Hence this patch allocates
   BL32 to the memory region occupied by BL31 for AArch32 builds.

   As a side-effect of this change, the ARM_TSP_RAM_LOCATION macro cannot
   be used to control the load address of BL32 in AArch32 mode which was
   never the intention of the macro anyway.

2. A static assert is added to sp_min linker script to check that the progbits
   are within the bounds expected when overlaid with other images.

3. Fix specifying `SPD` when building Juno for AArch32 mode. Due to the quirks
   involved when building Juno for AArch32 mode, the build option SPD needed to
   specifed. This patch corrects this and also updates the documentation in the
   user-guide.

4. Exclude BL31 from the build and FIP when building Juno for AArch32 mode. As
   a result the previous assumption that BL31 must be always present is removed
   and the certificates for BL31 is only generated if `NEED_BL31` is defined.

Change-Id: I1c39bbc0abd2be8fbe9f2dea2e9cb4e3e3e436a8
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

For Trusted Board Boot, BL2 needs more space to support the ECDSA
and ECDSA+RSA algorithms.

Change-Id: Ie7eda9a1315ce836dbc6d18d6588f8d17891a92d
Signed-off-by: Qixiang Xu <qixiang.xu@arm.com>

An earlier patch added provision for the platform to provide secure
interrupt properties. ARM platforms already has a list of interrupts
that fall into different secure groups.

This patch defines macros that enumerate interrupt properties in the
same fashion, and points the driver driver data to a list of interrupt
properties rather than list of secure interrupts on ARM platforms.  The
deprecated interrupt list definitions are however retained to support
legacy builds.

Configuration applied to individual interrupts remain unchanged, so no
runtime behaviour change expected.

NOTE: Platforms that use the arm/common function
plat_arm_gic_driver_init() must replace their PLAT_ARM_G1S_IRQS and
PLAT_ARM_G0_IRQS macro definitions with PLAT_ARM_G1S_IRQ_PROPS and
PLAT_ARM_G0_IRQ_PROPS macros respectively, using the provided
INTR_PROP_DESC macro.

Change-Id: I24d643b83e3333753a3ba97d4b6fb71e16bb0952
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

On ARM platforms, the maximum size of the address space is limited
to 32-bits as defined in arm_def.h. In order to access DRAM2, which
is defined beyond the 32-bit address space, the maximum address space
is increased to 36-bits in AArch64. It is possible to increase the
virtual space for AArch32, but it is more difficult and not supported
for now.

NOTE - the actual maximum memory address space is platform dependent
and is checked at run-time by querying the PARange field in the
ID_AA64MMFR0_EL1 register.

Change-Id: I6cb05c78a63b1fed96db9a9773faca04a5b93d67
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

mem_protect needs some kind of non-volatile memory because it has
to remember its state across reset and power down events.
The most suitable electronic part for this feature is a NVRAM
which should be only accesible from the secure world. Juno and
FVP lack such hardware and for this reason the MEM_PROTECT
functionality is implemented with Flash EEPROM memory on both
boards, even though this memory is accesible from the non-secure
world. This is done only to show a full implementation of
these PSCI features, but an actual system shouldn't use a
non-secure NVRAM to implement it.

The EL3 runtime software will write the mem_protect flag and BL2
will read and clear the memory ranges if enabled. It is done in
BL2 because it reduces the time that TF needs access to the full
non-secure memory.

The memory layout of both boards is defined using macros which
take different values in Juno and FVP platforms. Generic platform
helpers are added that use the platform specific macros to generate
a mem_region_t that is valid for the platform.

Change-Id: I2c6818ac091a2966fa07a52c5ddf8f6fde4941e9
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

For Trusted Board Boot, BL1 RW section and BL2 need more space to
support the ECDSA algorithm. Specifically, PLAT_ARM_MAX_BL1_RW_SIZE
is increased on ARM platforms.

And on the Juno platform:
    - BL2 size, PLAT_ARM_MAX_BL2_SIZE is increased.
    - SCP_BL2 is loaded into the space defined by BL31_BASE ->
      BL31_RW_BASE. In order to maintain the same size space for
      SCP_BL2,PLAT_ARM_MAX_BL31_SIZE is increased.

Change-Id: I379083f918b40ab1c765da4e71780d89f0058040
Co-Authored-By: David Cunado <david.cunado@arm.com>
Signed-off-by: Qixiang Xu <qixiang.xu@arm.com>

This patch does the required changes to enable CSS platforms
to build and use the SDS framework. Since SDS is always coupled with
SCMI protocol, the preexisting SCMI build flag is now renamed to
`CSS_USE_SCMI_SDS_DRIVER` which will enable both SCMI and SDS on
CSS platforms. Also some of the workarounds applied for SCMI are
now removed with SDS in place.

Change-Id: I94e8b93f05e3fe95e475c5501c25bec052588a9c
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch fixes the PLAT_LOG_LEVEL_ASSERT to 40 which corresponds
to LOG_LEVEL_INFO. Having this level of log for assertions means that the
`assert()` will not generate the strings implied in the expression taken
as parameter. This allows to save some memory when Juno is built for
LOG_LEVEL = LOG_LEVEL_VERBOSE and DEBUG = 1.

Fixes ARM-software/tf-issues#511

Change-Id: Id84a40f803ab07a5a8f6e587167af96694a07d04
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Trusted OS may have extra images to be loaded. Load them one by one
and do the parsing. In this patch, ARM TF need to load up to 3 images
for optee os: header, pager and paged images. Header image is the info
about optee os and images. Pager image include pager code and data.
Paged image include the paging parts using virtual memory.

Change-Id: Ia3bcfa6d8a3ed7850deb5729654daca7b00be394
Signed-off-by: Summer Qin <summer.qin@arm.com>

Recent patches to reduce the memory footprint of BL images have
resulted in saving several pages of memory. This patch reduces
the BL2 size limit by 20KB for Juno when ARM_BOARD_OPTIMISE_MEM=1
so that more free space can be freed up for Trusted OS (BL32). Also
SCP_BL2/SCP_BL2U size is now restricted to 80K.

Change-Id: I1573d7a34e24d15e4abce8a14da40dbb5dc81e37
Signed-off-by: Soby Mathew <soby.mathew@arm.com>