GitLab

Currently, BLs are mapping the GIC memory region as read-write
for all cores on boot-up.

This opens up the security hole where the active core can write
the GICR frame of fused/inactive core. To avoid this issue, disable
the GICR frame of all inactive cores as below:

1. After primary CPU boots up, map GICR region of all cores as
   read-only.
2. After primary CPU boots up, map its GICR region as read-write
   and initialize its redistributor interface.
3. After secondary CPU boots up, map its GICR region as read-write
   and initialize its redistributor interface.
4. All unused/fused core's redistributor regions remain read-only and
   write attempt to such protected regions results in an exception.

As mentioned above, this patch offers only the GICR memory-mapped
region protection considering there is no facility at the GIC IP
level to avoid writing the redistributor area.

These changes are currently done in BL31 of Arm FVP and guarded under
the flag 'FVP_GICR_REGION_PROTECTION'.

As of now, this patch is tested manually as below:
1. Disable the FVP cores (core 1, 2, 3) with core 0 as an active core.
2. Verify data abort triggered by manually updating the ‘GICR_CTLR’
   register of core 1’s(fused) redistributor from core 0(active).

Change-Id: I86c99c7b41bae137b2011cf2ac17fad0a26e776d
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>

Enable basic support for Neoverse-N2 CPUs.
Signed-off-by: Javier Almansa Sobrino <javier.almansasobrino@arm.com>
Change-Id: I498adc2d9fc61ac6e1af8ece131039410872e8ad

Change-Id: Ieb411e2f8092fa82062e619305b680673a8f184f
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>

Change-Id: Ic0ca51a855660509264ff0d084c068e1421ad09a
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>

This patch adds dependencies to the generated configuration
files that are included in the FIP. This fixes occasional
build errors that occur when the FIP happens to be built first.

Change-Id: I5a2bf724ba3aee13954403b141f2f19b4fd51d1b
Signed-off-by: Anders Dellien <anders.dellien@arm.com>

Using the Fconf, register base address of the various nv-counters
(currently, trusted, non-trusted nv-counters) are moved to the
device tree and retrieved during run-time. This feature is
enabled using the build option COT_DESC_IN_DTB.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I236f532e63cea63b179f60892cb406fc05cd5830

SP804 TIMER is not platform specific, and current code base adds
multiple defines to use this driver. Like FVP_USE_SP804_TIMER and
FVP_VE_USE_SP804_TIMER.

This patch removes platform specific build flag and adds generic
flag `USE_SP804_TIMER` to be set to 1 by platform if needed.

Change-Id: I5ab792c189885fd1b98ddd187f3a38ebdd0baba2
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

Provide manifest and build options to boot OP-TEE as a
guest S-EL1 Secure Partition on top of Hafnium in S-EL2.

Increase ARM_SP_MAX_SIZE to cope with OP-TEE debug build image.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: Idd2686fa689a78fe2d05ed92b1d23c65e2edd4cb

This patch adds support for Measured Boot functionality
to FVP platform code. It also defines new properties
in 'tpm_event_log' node to store Event Log address and
it size
'tpm_event_log_sm_addr'
'tpm_event_log_addr'
'tpm_event_log_size'
in 'event_log.dtsi' included in 'fvp_tsp_fw_config.dts'
and 'fvp_nt_fw_config.dts'. The node and its properties
are described in binding document
'docs\components\measured_boot\event_log.rst'.

Change-Id: I087e1423afcb269d6cfe79c1af9c348931991292
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

This patch moves all GICv2 driver files into new added
'gicv2.mk' makefile for the benefit of the generic driver
which can evolve in the future without affecting platforms.

NOTE: Usage of 'drivers/arm/gic/common/gic_common.c' file
is now deprecated and platforms with GICv2 driver need to
be modified to include 'drivers/arm/gic/v2/gicv2.mk' in
their makefiles.

Change-Id: Ib10e71bdda0e5c7e80a049ddce2de1dd839602d1
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

Passed the address of fw_config instead of soc_fw_config
as arg1 to BL31 from BL2 for ARM fvp platform.

BL31 then retrieve load-address of other device trees
from fw_config device tree.
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ib7e9581cd765d76111dcc3b7e0dafc12503c83c1

Moved BL2 configuration nodes from fw_config to newly
created tb_fw_config device tree.

fw_config device tree's main usage is to hold properties shared
across all BLx images.
An example is the "dtb-registry" node, which contains the
information about the other device tree configurations
(load-address, size).

Also, Updated load-address of tb_fw_config which is now located
after fw_config in SRAM.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ic398c86a4d822dacd55b5e25fd41d4fe3888d79a

Using the fconf framework, the Group 0 and Group 1 secure interrupt
descriptors are moved to device tree and retrieved in runtime. This
feature is enabled by the build flag SEC_INT_DESC_IN_FCONF.

Change-Id: I360c63a83286c7ecc2426cd1ff1b4746d61e633c
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

The only difference between GIC-500 and GIC-600 relevant to TF-A is the
differing power management sequence.
A certain GIC implementation is detectable at runtime, for instance by
checking the IIDR register. Let's add that test before initiating the
GIC-600 specific sequence, so the code can be used on both GIC-600 and
GIC-500 chips alike, without deciding on a GIC chip at compile time.

This means that the GIC-500 "driver" is now redundant. To allow minimal
platform support, add a switch to disable GIC-600 support.

Change-Id: I17ea97d9fb05874772ebaa13e6678b4ba3415557
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

This should allow git to easily track file moves
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
Change-Id: I1592cf39a4f94209c560dc6d1a8bc1bfb21d8327

We query the UART base address and clk frequency in runtime
using fconf getter APIs.

Change-Id: I5f4e84953be5f384472bf90720b706d45cb86260
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

Query the GICD and GICR base addresses in runtime using fconf getter
APIs.
Signed-off-by: Lauren Wehrmeister <lauren.wehrmeister@arm.com>
Change-Id: I309fb2874f3329ddeb8677ddb53ed4c02199a1e9

This patch adds support for GICv4 extension for FVP platform.

Change-Id: Ia389b61266af669b1ca9b999a8b76476cab214f4
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

As GCC manual says, -D option defines a macro as 1, if =<value> is omitted.

  -D <name>
      Predefine <name> as a macro, with definition 1.

The same applied with Clang, too.

In the context of -D option, =1 is always redundant.

Change-Id: I487489a1ea3eb51e734741619c1e65dab1420bc4
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

-D is a preprocessor flag that defines a macro. So, adding it to
BL*_CPPFLAGS makes more sense. You can reference it not only from
.c files but also from .S files.

Change-Id: Ib4f2f27a3ed3eae476a6a32da7ab5225ad0649de
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This patch moves all GICv3 driver files into new added
'gicv3.mk' makefile for the benefit of the generic driver
which can evolve in the future without affecting platforms.
The patch adds GICv3 driver configuration flags
'GICV3_IMPL', 'GICV3_IMPL_GIC600_MULTICHIP' and
'GICV3_OVERRIDE_DISTIF_PWR_OPS' described in
'GICv3 driver options' section of 'build-option.rst'
document.

NOTE: Platforms with GICv3 driver need to be modified to
include 'drivers/arm/gic/v3/gicv3.mk' in their makefiles.

Change-Id: If055f6770ff20f5dee5a3c99ae7ced7cdcac5c44
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

Rather than creating entry in plat_arm_mmap array to map the
entire DRAM region in BL31/SP_MIN, only map a smaller region holding
HW_CONFIG DTB. Consequently, an increase in number of sub-translation
tables(level-2 and level-3) i.e., MAX_XLAT_TABLES is necessary to map
the new region in memory.

In order to accommodate the increased code size in BL31 i.e.,
PROGBITS, the max size of BL31 image is increased by 0x1000(4K).

Change-Id: I540b8ee550588e22a3a9fb218183d2ab8061c851
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

Merge the previously introduced arm_fconf_io_storage into arm_io_storage. This
removes the duplicate io_policies and functions definition.

This patch:
- replace arm_io_storage.c with the content of arm_fconf_io_storage.c
- rename the USE_FCONF_BASED_IO option into ARM_IO_IN_DTB.
- use the ARM_IO_IN_DTB option to compile out io_policies moved in dtb.
- propagate DEFINES when parsing dts.
- use ARM_IO_IN_DTB to include or not uuid nodes in fw_config dtb.
- set the ARM_IO_IN_DTB to 0 by default for fvp. This ensure that the behavior
  of fvp stays the same as it was before the introduction of fconf.

Change-Id: Ia774a96d1d3a2bccad29f7ce2e2b4c21b26c080e
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

Necessary infrastructure added to integrate fconf framework in BL31 & SP_MIN.
Created few populator() functions which parse HW_CONFIG device tree
and registered them with fconf framework. Many of the changes are
only applicable for fvp platform.

This patch:
1. Adds necessary symbols and sections in BL31, SP_MIN linker script
2. Adds necessary memory map entry for translation in BL31, SP_MIN
3. Creates an abstraction layer for hardware configuration based on
   fconf framework
4. Adds necessary changes to build flow (makefiles)
5. Minimal callback to read hw_config dtb for capturing properties
   related to GIC(interrupt-controller node)
6. updates the fconf documentation

Change-Id: Ib6292071f674ef093962b9e8ba0d322b7bf919af
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

This patch provides separation of GICD, GICR accessor
functions and adds new macros for GICv3 registers access
as a preparation for GICv3.1 and GICv4 support.
NOTE: Platforms need to modify to include both
'gicdv3_helpers.c' and 'gicrv3_helpers.c' instead of the
single helper file previously.

Change-Id: I1641bd6d217d6eb7d1228be3c4177b2d556da60a
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

This patch introduces a build flag which allows the xlat tables
to be mapped in a read-only region within BL31 memory. It makes it
much harder for someone who has acquired the ability to write to
arbitrary secure memory addresses to gain control of the
translation tables.

The memory attributes of the descriptors describing the tables
themselves are changed to read-only secure data. This change
happens at the end of BL31 runtime setup. Until this point, the
tables have read-write permissions. This gives a window of
opportunity for changes to be made to the tables with the MMU on
(e.g. reclaiming init code). No changes can be made to the tables
with the MMU turned on from this point onwards. This change is also
enabled for sp_min and tspd.

To make all this possible, the base table was moved to .rodata. The
penalty we pay is that now .rodata must be aligned to the size of
the base table (512B alignment). Still, this is better than putting
the base table with the higher level tables in the xlat_table
section, as that would cost us a full 4KB page.

Changing the tables from read-write to read-only cannot be done with
the MMU on, as the break-before-make sequence would invalidate the
descriptor which resolves the level 3 page table where that very
descriptor is located. This would make the translation required for
writing the changes impossible, generating an MMU fault.

The caches are also flushed.
Signed-off-by: Petre-Ionut Tudor <petre-ionut.tudor@arm.com>
Change-Id: Ibe5de307e6dc94c67d6186139ac3973516430466

Also update copyright statements

Change-Id: Iba0305522ac0f2ddc4da99127fd773f340e67300
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>

Change-Id: I686fd623b8264c85434853a2a26ecd71e9eeac01
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>

This patch repurposes the TOS FW configuration file as the manifest for
the SPM core component which will reside at the secure EL adjacent to
EL3. The SPM dispatcher component will use the manifest to determine how
the core component must be initialised. Routines and data structure to
parse the manifest have also been added.
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Change-Id: Id94f8ece43b4e05609f0a1d364708a912f6203cb

Use the firmware configuration framework to store the io_policies
information inside the configuration device tree instead of the static
structure in the code base.

The io_policies required by BL1 can't be inside the dtb, as this one is
loaded by BL1, and only available at BL2.

This change currently only applies to FVP platform.

Change-Id: Ic9c1ac3931a4a136aa36f7f58f66d3764c1bfca1
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

This patch introduces a better separation between the trusted-boot
related properties, and the dynamic configuration DTBs loading
information.

The dynamic configuration DTBs properties are moved to a new node:
`dtb-registry`. All the sub-nodes present will be provided to the
dynamic config framework to be loaded. The node currently only contains
the already defined configuration DTBs, but can be extended for future
features if necessary.
The dynamic config framework is modified to use the abstraction provided
by the fconf framework, instead of directly accessing the DTBs.

The trusted-boot properties are kept under the "arm,tb_fw" compatible
string, but in a separate `tb_fw-config` node.
The `tb_fw-config` property of the `dtb-registry` node simply points
to the load address of `fw_config`, as the `tb_fw-config` is currently
part of the same DTB.

Change-Id: Iceb6c4c2cb92b692b6e28dbdc9fb060f1c46de82
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

Enables usage of ARM_ROTPK_LOCATION=regs for FVP board.
Removes hard-coded developer keys. Instead, setting
ARM_ROTPK_LOCATION=devel_* takes keys from default directory.
In case of ROT_KEY specified - generates a new hash and replaces the
original.

Note: Juno board was tested by original feature author and was not tested
for this patch since we don't have access to the private key. Juno
implementation was moved to board-specific file without changing
functionality. It is not known whether byte-swapping is still needed
for this platform.

Change-Id: I0fdbaca0415cdcd78f3a388551c2e478c01ed986
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>

The reclaim init code functionality relies on forward reference in the
linker script. The LLVM linker does not process it correctly.

Change-Id: I993aeb9587bfa07af25b60ed823a6a2c5e970c94
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
Signed-off-by: Zelalem Aweke <zelalem.aweke@arm.com>

The Secure Partition Manager (SPM) prototype implementation is
being removed. This is preparatory work for putting in place a
dispatcher component that, in turn, enables partition managers
at S-EL2 / S-EL1.

This patch removes:

- The core service files (std_svc/spm)
- The Resource Descriptor headers (include/services)
- SPRT protocol support and service definitions
- SPCI protocol support and service definitions

Change-Id: Iaade6f6422eaf9a71187b1e2a4dffd7fb8766426
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>

There are two different implementations of Secure Partition
management in TF-A. One is based on the "Management Mode" (MM)
design, the other is based on the Secure Partition Client Interface
(SPCI) specification. Currently there is a dependency between their
build flags that shouldn't exist, making further development
harder than it should be. This patch removes that
dependency, making the two flags function independently.

Before: ENABLE_SPM=1 is required for using either implementation.
        By default, the SPCI-based implementation is enabled and
        this is overridden if SPM_MM=1.

After: ENABLE_SPM=1 enables the SPCI-based implementation.
       SPM_MM=1 enables the MM-based implementation.
       The two build flags are mutually exclusive.

Note that the name of the ENABLE_SPM flag remains a bit
ambiguous - this will be improved in a subsequent patch. For this
patch the intention was to leave the name as-is so that it is
easier to track the changes that were made.

Change-Id: I8e64ee545d811c7000f27e8dc8ebb977d670608a
Signed-off-by: Paul Beesley <paul.beesley@arm.com>

Provide an SMC interface to the 9p filesystem. This permits
accessing firmware drivers through a common interface, using
standardized read/write/control operations.
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I9314662314bb060f6bc02714476574da158b2a7d

Earlier PIE support was enabled for all arm platforms when
RESET_TO_BL31=1, but later on it was restricted only to FVP with patch
SHA d4580d17

 because of n1sdp platform.

Now it has been verified that PIE does work for n1sdp platform also, so
enabling it again for all arm platforms.

Change-Id: I05ad4f1775ef72e7cb578ec9245cde3fbce971a5
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>

Change-Id: I1ea2bf088f1e001cdbd377cbfb7c6a2866af0422
Signed-off-by: Imre Kis <imre.kis@arm.com>

Change-Id: I645442d52a295706948e2cac88c36c1a3cb0bc47
Signed-off-by: Imre Kis <imre.kis@arm.com>

Not tested on FVP Model.

Change-Id: Iedebc5c1fbc7ea577e94142b7feafa5546f1f4f9
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>