GitLab

The SCP firmware on the ARM FPGA initialises the UART already. This allows
us to treat the PL011 as an SBSA Generic UART, which does not require
any further setup.

This in particular removes the need for any baudrate and base clock related
settings to be hard coded into the BL31 image.

Change-Id: I16fc943526267356b97166a7068459e06ff77f0f
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Now that we have an implementation for getting the node offset of the
stdout-path property in the generic fdt_wrappers code, use that to
replace the current ST platform specific implementation.

Change-Id: I5dd05684e7ca3cb563b5f71c885e1066393e057e
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The stdout-path property in the /chosen node of a DTB points to a device
node, which is used for boot console output.
On most (if not all) ARM based platforms this is the debug UART.
The ST platform code contains a function to parse this property and
chase down eventual aliases to learn the node offset of this UART node.

Introduce a slightly more generalised version of this ST platform function
in the generic fdt_wrappers code. This will be useful for other platforms
as well.

Change-Id: Ie6da47ace7833861b5e35fe8cba49835db3659a5
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The STM32 platform port parse DT nodes to find base address to
peripherals. It does this by using its own implementation, even though
this functionality is generic and actually widely useful outside of the
STM32 code.

Re-implement fdt_get_reg_props_by_name() on top of the newly introduced
fdt_get_reg_props_by_index() function, and move it to fdt_wrapper.c.
This is removes the assumption that #address-cells and #size-cells are
always one.

Change-Id: I6d584930262c732b6e0356d98aea50b2654f789d
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

At the moment the fconf_populate_gicv3_config() implementation is
somewhat incomplete: First it actually fails to store the retrieved
information (the local addr[] array is going nowhere), but also it makes
quite some assumptions about the device tree passed to it: it needs to
use two address-cells and two size-cells, and also requires all five
register regions to be specified, where actually only the first two
are mandatory according to the binding (and needed by our code).

Fix this by introducing a proper generic function to retrieve "reg"
property information from a DT node:
We retrieve the #address-cells and #size-cells properties from the
parent node, then use those to extract the right values from the "reg"
property. The function takes an index to select one region of a reg
property.

This is loosely based on the STM32 implementation using "reg-names",
which we will subsume in a follow-up patch.

Change-Id: Ia59bfdf80aea4e36876c7b6ed4d153e303f482e8
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The STM32 platform code uses its own set of FDT helper functions,
although some of them are fairly generic.

Remove the implementation of fdt_read_uint32_default() and implement it
on top of the newly introduced fdt_read_uint32() function, then convert
all users over.

This also fixes two callers, which were slightly abusing the "default"
semantic.

Change-Id: I570533362b4846e58dd797a92347de3e0e5abb75
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Our fdtw_read_cells() implementation goes to great lengths to
sanity-check every parameter and result, but leaves a big hole open:
The size of the storage the value pointer points at needs to match the
number of cells given. This can't be easily checked at compile time,
since we lose the size information by using a void pointer.
Regardless the current usage of this function is somewhat wrong anyways,
since we use it on single-element, fixed-length properties only, for
which the DT binding specifies the size.
Typically we use those functions dealing with a number of cells in DT
context to deal with *dynamically* sized properties, which depend on
other properties (#size-cells, #clock-cells, ...), to specify the number
of cells needed.

Another problem with the current implementation is the use of
ambiguously sized types (uintptr_t, size_t) together with a certain
expectation about their size. In general there is no relation between
the length of a DT property and the bitness of the code that parses the
DTB: AArch64 code could encounter 32-bit addresses (where the physical
address space is limited to 4GB [1]), while AArch32 code could read
64-bit sized properties (/memory nodes on LPAE systems, [2]).

To make this more clear, fix the potential issues and also align more
with other DT users (Linux and U-Boot), introduce functions to explicitly
read uint32 and uint64 properties. As the other DT consumers, we do this
based on the generic "read array" function.
Convert all users to use either of those two new functions, and make
sure we never use a pointer to anything other than uint32_t or uint64_t
variables directly.

This reveals (and fixes) a bug in plat_spmd_manifest.c, where we write
4 bytes into a uint16_t variable (passed via a void pointer).

Also we change the implementation of the function to better align with
other libfdt users, by using the right types (fdt32_t) and common
variable names (*prop, prop_names).

[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi#n874
[2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm/boot/dts/ecx-2000.dts



Change-Id: I718de960515117ac7a3331a1b177d2ec224a3890
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The device tree parsing code for the STM32 platform is using its own FDT
helper functions, some of them being rather generic.
In particular the existing fdt_read_uint32_array() implementation is now
almost identical to the new generic code in fdt_wrappers.c, so we can
remove the ST specific version and adjust the existing callers.

Compared to the original ST implementation the new version takes a
pointer to the DTB as the first argument, and also swaps the order of
the number of cells and the pointer.

Change-Id: Id06b0f1ba4db1ad1f733be40e82c34f46638551a
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Currently our fdtw_read_array() implementation requires the length of
the property to exactly match the requested size, which makes it less
flexible for parsing generic device trees.
Also the name is slightly misleading, since we treat the cells of the
array as 32 bit unsigned integers, performing the endianess conversion.

To fix those issues and align the code more with other DT users (Linux
kernel or U-Boot), rename the function to "fdt_read_uint32_array", and
relax the length check to only check if the property covers at least the
number of cells we request.
This also changes the variable names to be more in-line with other DT
users, and switches to the proper data types.

This makes this function more useful in later patches.

Change-Id: Id86f4f588ffcb5106d4476763ecdfe35a735fa6c
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Move the data section to the common header.

I slightly tweaked some scripts as follows:

[1] bl1.ld.S has ALIGN(16). I added DATA_ALIGN macro, which is 1
    by default, but overridden by bl1.ld.S. Currently, ALIGN(16)
    of the .data section is redundant because commit 41286590


    ("Fix boot failures on some builds linked with ld.lld.") padded
    out the previous section to work around the issue of LLD version
    <= 10.0. This will be fixed in the future release of LLVM, so
    I am keeping the proper way to align LMA.

[2] bl1.ld.S and bl2_el3.ld.S define __DATA_RAM_{START,END}__ instead
    of __DATA_{START,END}__. I put them out of the .data section.

[3] SORT_BY_ALIGNMENT() is missing tsp.ld.S, sp_min.ld.S, and
    mediatek/mt6795/bl31.ld.S. This commit adds SORT_BY_ALIGNMENT()
    for all images, so the symbol order in those three will change,
    but I do not think it is a big deal.

Change-Id: I215bb23c319f045cd88e6f4e8ee2518c67f03692
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The stacks section is the same for all BL linker scripts.

Move it to the common header file.

Change-Id: Ibd253488667ab4f69702d56ff9e9929376704f6c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Change-Id: Ib39e53eb53521b8651fb30b7bf0058f7669569d5

RD-Daniel Config-XLR platform has four identical chips connected via a
high speed coherent CCIX link. Each chip has four Neoverse cores
connected via coherent CMN interconnect.

Change-Id: I37d1b91f2b6ba08f61c64d0288bc16a429836c08
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

This commit fixes an assertion that was triggering in certain contexts:

    ERROR: mmap_add_region_check() failed. error -22
    ASSERT: lib/xlat_tables_v2/xlat_tables_core.c:790

Change-Id: Ia55b3fb4f496c8cd791ea6093d122edae0a7e92a
Signed-off-by: Chris Kay <chris.kay@arm.com>
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

By writing 0 to CLUSTERPWRDN DSU register bit 0, we send an
advisory to the power controller that cluster power is not required
when all cores are powered down.

The AArch32 CLUSTERPWRDN register is architecturally mapped to the
AArch64 CLUSTERPWRDN_EL1 register

Change-Id: Ie6e67c1c7d811fa25c51e2e405ca7f59bd20c81b
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

A single chip platform requires five mmap entries and a corresponding
number of translation tables. For every additional chip in the system,
three additional mmap entries are required to map the shared SRAM and
the IO regions. A corresponding number of additional translation
tables are required as well.

Change-Id: I1332a1305f2af62181387cf36954f6fb0e6f11ed
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

fix coverity reported issues
1. uninitialized var,
2. check for negative val on unsigned variable
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Change-Id: I28b7517135ba6c1ba0df04f0c73189cf84ba89e6

The arm_fpga platform code contains an dubious line to initialise some
timer. On closer inspection this turn out to be bogus, as this was only
needed on some special (older) FPGA board, and is actually not needed on
the current model. Also the base address was wrong anyways.

Remove the code entirely.

Change-Id: I02e71aea645051b5addb42d972d7a79f04b81106
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

RD-Daniel uses GIC-Clayton as its interrupt controller which is an
implementation of GICv4.1 architecture. Hence for RD-Daniel, enable
GICv4 extension support.

Change-Id: I45ae8c82376f8fe8fc0666306822ae2db74e71b8
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>

This patch adds support for GICv4 extension for FVP platform.

Change-Id: Ia389b61266af669b1ca9b999a8b76476cab214f4
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

Increased the maximum size of BL2 image in order to
accommodate the BL2 image when TF-A build with no compiler
optimization for ARM platform.

Note: As of now, "no compiler optimization" build works
only when TRUSTED_BOOT_BOARD option is set to 0.

This change is verified using below CI configuration:
1. juno-no-optimize-default:juno-linux.uboot
2. fvp-no-optimize-default,fvp-default:fvp-tftf-fip.tftf-aemv8a-debug

Change-Id: I5932621237f8acd1b510682388f3ba78eae90ea4
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>

Default board configuration was set to bcm958742k which is not present
in current codebase. This causes a default platform build to fail.
Changing to bcm958742t.
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
Change-Id: Ie24f94ef0ef316ff56fe142df5de45d70ba93c28

with commit a6ea06f5

, the way platform includes gicv3 files has been
modified, this patch adapts to new method of including gicv3 files
for arm_fpga platform.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ic5ccae842b39b7db06d4f23c5738b174c42edf63

Add SPI Nor flash support

Change-Id: I0cde3fdb4dcad5bcaf445b3bb48e279332bd28af
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>

Add iproc spi driver

Change-Id: I652efab1efd9c487974dae9cb9d98b9b8e3759c4
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>

Add emmc driver for Broadcom platforms

Change-Id: I126a6dfccd41062cb0b856f2c2fb1f724730b95e
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>

Change-Id: Icfef5b6923dc292e637001045a334c499d346fe9
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>

Change-Id: I5daa3f2b4b9d85cb857547a588571a9aa8ad05c2
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>

Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Change-Id: Ic1a392a633b447935fa3a7528326c97845f5b1bc

Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Change-Id: Iabeaee35c22608c93945c8295bf70947b0f6049a

The platform io policies array is now always accessed through a fconf getter.
This gives us an ideal spot to check for out-of-bound accesses.

Remove the assertion in plat_get_image_source(), which is now redundant.

Change-Id: Iefe808d530229073b68cbd164d927b8b6662a217
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

Signed-off-by: Javier Almansa Sobrino <javier.almansasobrino@arm.com>
Change-Id: I397b642eff8a09b201f497f8d2ba39e2460c0dba

This is not used in BL31 or Bl32 for this platform.

Pass it to BL2_CPPFLAGS instead of defining it for all BL images.

This will produce slightly smaller BL31 and Bl32.

Change-Id: I66ec5179f8dc5b112e65547335e7dd0a0f4074cd
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

As GCC manual says, -D option defines a macro as 1, if =<value> is omitted.

  -D <name>
      Predefine <name> as a macro, with definition 1.

The same applied with Clang, too.

In the context of -D option, =1 is always redundant.

Change-Id: I487489a1ea3eb51e734741619c1e65dab1420bc4
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Commit d5e97a1d ("Build: define IMAGE_AT_EL1 or IMAGE_AT_EL3
globally for C files") does not have commit 848a7e8c ("Build:
introduce per-BL CPPFLAGS and ASFLAGS") as an ancestor because
they were pulled almost at the same time.

This is a follow-up conversion to be consistent with commit
11a3c5ee

 ("plat: pass -D option to BL*_CPPFLAGS instead of
BL*_CFLAGS").

With this change, the command line option, IMAGE_AT_EL3, will be
passed to .S files as well.

I remove the definition in include/lib/cpus/aarch64/cpu_macros.S

Otherwise, the following error would happen.

  include/lib/cpus/aarch64/cpu_macros.S:29:0: error: "IMAGE_AT_EL3" redefined [-Werror]

Change-Id: I943c8f22356483c2ae3c57b515c69243a8fa6889
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Move the bss section to the common header. This adds BAKERY_LOCK_NORMAL
and PMF_TIMESTAMP, which previously existed only in BL31. This is not
a big deal because unused data should not be compiled in the first
place. I believe this should be controlled by BL*_SOURCES in Makefiles,
not by linker scripts.

I investigated BL1, BL2, BL2U, BL31 for plat=fvp, and BL2-AT-EL3,
BL31, BL31 for plat=uniphier. I did not see any more  unexpected
code addition.

The bss section has bigger alignment. I added BSS_ALIGN for this.

Currently, SORT_BY_ALIGNMENT() is missing in sp_min.ld.S, and with this
change, the BSS symbols in SP_MIN will be sorted by the alignment.
This is not a big deal (or, even better in terms of the image size).

Change-Id: I680ee61f84067a559bac0757f9d03e73119beb33
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The common section data are repeated in many linker scripts (often
twice in each script to support SEPARATE_CODE_AND_RODATA). When you
add a new read-only data section, you end up with touching lots of
places.

After this commit, you will only need to touch bl_common.ld.h when
you add a new section to RODATA_COMMON.

Replace a series of RO section with RODATA_COMMON, which contains
6 sections, some of which did not exist before.

This is not a big deal because unneeded data should not be compiled
in the first place. I believe this should be controlled by BL*_SOURCES
in Makefiles, not by linker scripts.

When I was working on this commit, the BL1 image size increased
due to the fconf_populator. Commit c452ba15

 ("fconf: exclude
fconf_dyn_cfg_getter.c from BL1_SOURCES") fixed this issue.

I investigated BL1, BL2, BL2U, BL31 for plat=fvp, and BL2-AT-EL3,
BL31, BL31 for plat=uniphier. I did not see any more  unexpected
code addition.

Change-Id: I5d14d60dbe3c821765bce3ae538968ef266f1460
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

These are mostly used to collect data from special structure,
and repeated in many linker scripts.

To differentiate the alignment size between aarch32/aarch64, I added
a new macro STRUCT_ALIGN.

While I moved the PMF_SVC_DESCS, I dropped #if ENABLE_PMF conditional.
As you can see in include/lib/pmf/pmf_helpers.h, PMF_REGISTER_SERVICE*
are no-op when ENABLE_PMF=0. So, pmf_svc_descs and pmf_timestamp_array
data are not populated.

Change-Id: I3f4ab7fa18f76339f1789103407ba76bda7e56d0
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This patch enables the Exception Handling Framework to service the WDT
interrupts on all Tegra platforms.

Verified that the watchdog timer interrupt fires after migrating to
the EHF.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I6b2e33da7841aa064e3a8f825c26fadf168cd0d5

We simulate the PSCI CPU_OFF operation by reseting the core via RMR.
For secondaries, that already puts them in the holding pen waiting for a
"warm boot" request as part of PSCI CPU_ON. For the BSP, we have to add
logic to distinguish a regular boot from a CPU_OFF state, where, like the
secondaries, the BSP needs to wait foor a "warm boot" request as part
of CPU_ON.

Testing done:

- ACS suite now passes more tests (since it repeatedly
calls code on secondaries via CPU_ON).

- Linux testing including offlining/onlineing CPU0, e.g.
"echo 0 > /sys/devices/system/cpu/cpu0/online".

Change-Id: Id0ae11a0ee0721b20fa2578b54dadc72dcbd69e0
Link: https://developer.trustedfirmware.org/T686

Signed-off-by: Andrei Warkentin <andrey.warkentin@gmail.com>
[Andre: adapt to unified plat_helpers.S, smaller fixes]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>