GitLab

Signed-off-by: Victor Chong <victor.chong@linaro.org>

Signed-off-by: Victor Chong <victor.chong@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Victor Chong <victor.chong@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Victor Chong <victor.chong@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Victor Chong <victor.chong@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Victor Chong <victor.chong@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>

Change-Id: Ib67b841ab621ca1ace3280e44cf3e1d83052cb73
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Signed-off-by: Victor Chong <victor.chong@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>

Let bl1 and bl2 have the ability to load images from emmc instead of
dram (mmap).
Signed-off-by: Victor Chong <victor.chong@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Victor Chong <victor.chong@linaro.org>

The security properties of some IP blocks are configured to secure mode
after reset. This means these IP blocks can only be accessed by cpus
in secure state by default. These should be configured correclty as needed.
Signed-off-by: y00241285 <yyangwei.yangwei@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>

This is currently the maximum allowed without affecting bootup.
Signed-off-by: Victor Chong <victor.chong@linaro.org>

to PLAT_POPLAR_NS_IMAGE_OFFSET
Signed-off-by: Victor Chong <victor.chong@linaro.org>

Per
https://github.com/sdrobertw/Poplar/blob/master/HardwareDocs/Processor_Datasheet_v2XX.pdf


there are 13 groups of GPIO controllers, not 12.
Signed-off-by: Victor Chong <victor.chong@linaro.org>

Pre-v8.2 platforms such as the Juno platform does not have
the Scalable Vector Extensions implemented and so the build
option ENABLE_SVE is set to zero.

This has a minor performance improvement with no functional
impact.

Change-Id: Ib072735db7a0247406f8b60e325b7e28b1e04ad1
Signed-off-by: David Cunado <david.cunado@arm.com>

Change-Id: Ibca6ea29be32783de666e0e0a0481668fc11860f
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The board features the Hi3798C V200 with an integrated quad-core
64-bit ARM Cortex A53 processor and high performance Mali T720 GPU,
making it capable of running any commercial set-top solution based on
Linux or Android. Its high performance specification also supports a
premium user experience with up to H.265 HEVC decoding of 4K video at
60 frames per second.

SOC  Hisilicon Hi3798CV200
CPU  Quad-core ARM Cortex-A53 64 bit
DRAM DDR3/3L/4 SDRAM interface, maximum 32-bit data width 2 GB
USB  Two USB 2.0 ports One USB 3.0 ports
CONSOLE  USB-micro port for console support
ETHERNET  1 GBe Ethernet
PCIE  One PCIe 2.0 interfaces
JTAG  8-Pin JTAG
EXPANSION INTERFACE  Linaro 96Boards Low Speed Expansion slot
DIMENSION Standard 160×120 mm 96Boards Enterprice Edition form factor
WIFI  802.11AC 2*2 with Bluetooth
CONNECTORS  One connector for Smart Card One connector for TSI

The platform boot sequence is as follows:
    l-loader --> arm_trusted_firmware --> u-boot

Repositories:
 - https://github.com/Linaro/poplar-l-loader.git
 - https://github.com/Linaro/poplar-u-boot.git



U-Boot is also upstream in the project's master branch.

Make sure you are using the correct branch on each one of these
repositories. The definition of "correct" might change over time (at
this moment in time this would be the "latest" branch).

Build Line:
make CROSS_COMPILE=aarch64-linux-gnu-  all fip SPD=none DEBUG=1
PLAT=poplar BL33=/path/to/u-boot.bin
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Tested-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Alex Elder <elder@linaro.org>