GitLab

This patch changes implementation for disabling Secure Cycle
Counter. For ARMv8.5 the counter gets disabled by setting
SDCR.SCCD bit on CPU cold/warm boot. For the earlier
architectures PMCR register is saved/restored on secure
world entry/exit from/to Non-secure state, and cycle counting
gets disabled by setting PMCR.DP bit.
In 'include\aarch32\arch.h' header file new
ARMv8.5-PMU related definitions were added.

Change-Id: Ia8845db2ebe8de940d66dff479225a5b879316f8
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}

The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).

For example, this patch had to be created because two headers were
called the same way: e0ea0928 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3 ("drivers: add tzc380 support").

This problem was introduced in commit 4ecca339

 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.

Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.

Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Having an active stack while enabling MMU has shown coherency problems.
This patch builds on top of translation library changes that introduces
MMU-enabling without using stacks.

Previously, with HW_ASSISTED_COHERENCY, data caches were disabled while
enabling MMU only because of active stack. Now that we can enable MMU
without using stack, we can enable both MMU and data caches at the same
time.

NOTE: Since this feature depends on using translation table library v2,
disallow using translation table library v1 with HW_ASSISTED_COHERENCY.

Fixes ARM-software/tf-issues#566

Change-Id: Ie55aba0c23ee9c5109eb3454cb8fa45d74f8bbb2
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

When the source code says 'SMCC' it is talking about the SMC Calling
Convention. The correct acronym is SMCCC. This affects a few definitions
and file names.

Some files have been renamed (smcc.h, smcc_helpers.h and smcc_macros.S)
but the old files have been kept for compatibility, they include the
new ones with an ERROR_DEPRECATED guard.

Change-Id: I78f94052a502436fdd97ca32c0fe86bd58173f2f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch introduces a new BL handover interface. It essentially allows
passing 4 arguments between the different BL stages. Effort has been made
so as to be compatible with the previous handover interface. The previous
blx_early_platform_setup() platform API is now deprecated and the new
blx_early_platform_setup2() variant is introduced. The weak compatiblity
implementation for the new API is done in the `plat_bl_common.c` file.
Some of the new arguments in the new API will be reserved for generic
code use when dynamic configuration support is implemented. Otherwise
the other registers are available for platform use.

Change-Id: Ifddfe2ea8e32497fe1beb565cac155ad9d50d404
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch introduces two workarounds for ARMv7 systems.  The
workarounds need to be applied prior to any `branch` instruction in
secure world.  This is achieved using a custom vector table where each
entry is an `add sp, sp, #1` instruction.

On entry to monitor mode, once the sequence of `ADD` instructions is
executed, the branch target buffer (BTB) is invalidated.  The bottom
bits of `SP` are then used to decode the exception entry type.

A side effect of this change is that the exception vectors are
installed before the CPU specific reset function.  This is now
consistent with how it is done on AArch64.

Note, on AArch32 systems, the exception vectors are typically tightly
integrated with the secure payload (e.g. the Trusted OS).  This
workaround will need porting to each secure payload that requires it.

The patch to modify the AArch32 per-cpu vbar to the corresponding
workaround vector table according to the CPU type will be done in a
later patch.

Change-Id: I5786872497d359e496ebe0757e8017fa98f753fa
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Clear exclusive monitor on SMC and FIQ entry for ARMv7 cores.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>

Currently TF does not initialise the PMCR_EL0 register in
the secure context or save/restore the register.

In particular, the DP field may not be set to one to prohibit
cycle counting in the secure state, even though event counting
generally is prohibited via the default setting of MDCR_EL3.SMPE
to 0.

This patch initialises PMCR_EL0.DP to one in the secure state
to prohibit cycle counting and also initialises other fields
that have an architectually UNKNOWN reset value.

Additionally, PMCR_EL0 is added to the list of registers that are
saved and restored during a world switch.

Similar changes are made for PMCR for the AArch32 execution state.

NOTE: secure world code at lower ELs that assume other values in PMCR_EL0
will be impacted.

Change-Id: Iae40e8c0a196d74053accf97063ebc257b4d2f3a
Signed-off-by: David Cunado <david.cunado@arm.com>

Add support for a minimal secure interrupt service in sp_min for
the AArch32 implementation. Hard code that only FIQs are handled.

Introduce bolean build directive SP_MIN_WITH_SECURE_FIQ to enable
FIQ handling from SP_MIN.

Configure SCR[FIQ] and SCR[FW] from generic code for both cold and
warm boots to handle FIQ in secure state from monitor.

Since SP_MIN architecture, FIQ are always trapped when system executes
in non secure state. Hence discard relay of the secure/non-secure
state in the FIQ handler.

Change-Id: I1f7d1dc7b21f6f90011b7f3fcd921e455592f5e7
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

This patch updates the el3_arch_init_common macro so that it fully
initialises essential control registers rather then relying on hardware
to set the reset values.

The context management functions are also updated to fully initialise
the appropriate control registers when initialising the non-secure and
secure context structures and when preparing to leave EL3 for a lower
EL.

This gives better alignement with the ARM ARM which states that software
must initialise RES0 and RES1 fields with 0 / 1.

This patch also corrects the following typos:

"NASCR definitions" -> "NSACR definitions"

Change-Id: Ia8940b8351dc27bc09e2138b011e249655041cfc
Signed-off-by: David Cunado <david.cunado@arm.com>

The current SMC context data structure `smc_ctx_t` and related helpers are
optimized for case when SMC call does not result in world switch. This was
the case for SP_MIN and BL1 cold boot flow. But the firmware update usecase
requires world switch as a result of SMC and the current SMC context helpers
were not helping very much in this regard. Therefore this patch does the
following changes to improve this:

1. Add monitor stack pointer, `spmon` to `smc_ctx_t`

The C Runtime stack pointer in monitor mode, `sp_mon` is added to the
SMC context, and the `smc_ctx_t` pointer is cached in `sp_mon` prior
to exit from Monitor mode. This makes is easier to retrieve the
context when the next SMC call happens. As a result of this change,
the SMC context helpers no longer depend on the stack to save and
restore the register.

This aligns it with the context save and restore mechanism in AArch64.

2. Add SCR in `smc_ctx_t`

Adding the SCR register to `smc_ctx_t` makes it easier to manage this
register state when switching between non secure and secure world as a
result of an SMC call.

Change-Id: I5e12a7056107c1701b457b8f7363fdbf892230bf
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/



Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

This patch introduces a build option to enable D-cache early on the CPU
after warm boot. This is applicable for platforms which do not require
interconnect programming to enable cache coherency (eg: single cluster
platforms). If this option is enabled, then warm boot path enables
D-caches immediately after enabling MMU.

Fixes ARM-Software/tf-issues#456

Change-Id: I44c8787d116d7217837ced3bcf0b1d3441c8d80e
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

The files affected by this patch don't really depend on `xlat_tables.h`.
By changing the included file it becomes easier to switch between the
two versions of the translation tables library.

Change-Id: Idae9171c490e0865cb55883b19eaf942457c4ccc
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

At present, warm-booted CPUs keep their caches disabled when enabling
MMU, and remains so until they enter coherency later.

On systems with hardware-assisted coherency, for which
HW_ASSISTED_COHERENCY build flag would be enabled, warm-booted CPUs can
have both caches and MMU enabled at once.

Change-Id: Icb0adb026e01aecf34beadf49c88faa9dd368327
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The AArch32 Procedure call Standard mandates that the stack must be aligned
to 8 byte boundary at external interfaces. This patch does the required
changes.

This problem was detected when a crash was encountered in
`psci_print_power_domain_map()` while printing 64 bit values. Aligning
the stack to 8 byte boundary resolved the problem.

Fixes ARM-Software/tf-issues#437

Change-Id: I517bd8203601bb88e9311bd36d477fb7b3efb292
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch uses the `el3_entrypoint_common` macro to initialize
CPU registers, in SP_MIN entrypoint.s file, in both cold and warm
boot path. It also adds conditional compilation, in cold and warm
boot entry path, based on RESET_TO_SP_MIN.

Change-Id: Id493ca840dc7b9e26948dc78ee928e9fdb76b9e4

This patch adds a minimal AArch32 secure payload SP_MIN. It relies on PSCI
library to initialize the normal world context. It runs in Monitor mode
and uses the runtime service framework to handle SMCs. It is added as
a BL32 component in the Trusted Firmware source tree.

Change-Id: Icc04fa6b242025a769c1f6c7022fde19459c43e9