GitLab

A new file added as part of arm-trusted-firmware#927 was missing the
SPDX license identifier - this patch adds the missing identifier.

Change-Id: Id1355f2bdca930b7e65bb54eff7e6c764ebb0d96
Signed-off-by: David Cunado <david.cunado@arm.com>

In AArch64, privileged exception levels control the execution state
(a.k.a. register width) of the immediate lower Exception Level; i.e.
whether the lower exception level executes in AArch64 or AArch32 state.
For an exception level to have its execution state changed at run time,
it must request the change by raising a synchronous exception to the
higher exception level.

This patch implements and adds such a provision to the ARM SiP service,
by which an immediate lower exception level can request to switch its
execution state. The execution state is switched if the request is:

  - raised from non-secure world;

  - raised on the primary CPU, before any secondaries are brought online
    with CPU_ON PSCI call;

  - raised from an exception level immediately below EL3: EL2, if
    implemented; otherwise NS EL1.

If successful, the SMC doesn't return to the caller, but to the entry
point supplied with the call. Otherwise, the caller will observe the SMC
returning with STATE_SW_E_DENIED code. If ARM Trusted Firmware is built
for AArch32, the feature is not supported, and the call will always
fail.

For the ARM SiP service:

  - Add SMC function IDs for both AArch32 and AArch64;
  - Increment the SiP service minor version to 2;
  - Adjust the number of supported SiP service calls.

Add documentation for ARM SiP service.

Fixes ARM-software/tf-issues#436

Change-Id: I4347f2d6232e69fbfbe333b340fcd0caed0a4cea
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/



Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

Replace all instances of checks with the new macro.

Change-Id: I0eec39b9376475a1a9707a3115de9d36f88f8a2a
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Following steps are required to boot JUNO in AArch32 state:
1> BL1, in AArch64 state, loads BL2.
2> BL2, in AArch64 state, initializes DDR.
  Loads SP_MIN & BL33 (AArch32 executable)images.
  Calls RUN_IMAGE SMC to go back to BL1.
3> BL1 writes AArch32 executable opcodes, to load and branch
  at the entrypoint address of SP_MIN, at HI-VECTOR address and
  then request for warm reset in AArch32 state using RMR_EL3.

This patch makes following changes to facilitate above steps:
* Added assembly function to carry out step 3 above.
* Added region in TZC that enables Secure access to the
  HI-VECTOR(0xFFFF0000) address space.
* AArch32 image descriptor is used, in BL2, to load
  SP_MIN and BL33 AArch32 executable images.

A new flag `JUNO_AARCH32_EL3_RUNTIME` is introduced that
controls above changes. By default this flag is disabled.

NOTE: BL1 and BL2 are not supported in AArch32 state for JUNO.

Change-Id: I091d56a0e6d36663e6d9d2bb53c92c672195d1ec
Signed-off-by: Yatharth Kochar <yatharth.kochar@arm.com>
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

ARM platforms have migrated to the translation tables library v2.
However, for testing purposes, it can be useful to temporarily switch
back to the old version.

This patch introduces the option `ARM_XLAT_TABLES_LIB_V1`, that switches
to v1 of the library when is set to 1. By default, it is 0, so that ARM
platforms use the new version unless specifically stated.

Updated User Guide.

Change-Id: I53d3c8dd97706f6af9c6fca0364a88ef341efd31
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This API makes sure that all the characters sent to the crash console
are output before returning from it.

Porting guide updated.

Change-Id: I1785f970a40f6aacfbe592b6a911b1f249bb2735
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch modifies some of the functions in ARM platform layer to cater
for the case when multi-threading `MT` is set in MPIDR. A new build flag
`ARM_PLAT_MT` is added, and when enabled, the functions accessing MPIDR
now assume that the `MT` bit is set for the platform and access the bit
fields accordingly.

Also, a new API plat_arm_get_cpu_pe_count is added when `ARM_PLAT_MT` is
enabled, returning the PE count within the physical cpu corresponding to
`mpidr`.

Change-Id: I04ccf212ac3054a60882761f4087bae299af13cb
Signed-off-by: Summer Qin <summer.qin@arm.com>

These source file definitions should be defined in generic
Makefiles so that all platforms can benefit. Ensure that the
symbols are properly marked as weak so they can be overridden
by platforms.

NOTE: This change is a potential compatibility break for
non-upstream platforms.

Change-Id: I7b892efa9f2d6d216931360dc6c436e1d10cffed
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

Modify ARM common makefile to use version 2 of the translation tables
library and include the new header in C files.

Simplify header dependencies related to this library to simplify the
change.

The following table contains information about the size increase in
bytes for BL1 after applying this patch. The code has been compiled for
different configurations of FVP in AArch64 mode with compiler GCC 4.9.3
20150413. The sizes have been calculated with the output of `nm` by
adding the size of all regions and comparing the total size before and
after the change. They are sumarized in the table below:

                               text   bss   data  total
        Release                +660   -20    +88   +728
        Debug                  +740   -20   +242   +962
        Debug (LOG_LEVEL=50)  +1120   -20   +317  +1417

Change-Id: I539e307f158ab71e3a8b771640001fc1bf431b29
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch introduces the following three platform interfaces:

* void plat_psci_stat_accounting_start(const psci_power_state_t *state_info)

  This is an optional hook that platforms can implement in order
  to perform accounting before entering a low power state.  This
  typically involves capturing a timestamp.

* void plat_psci_stat_accounting_stop(const psci_power_state_t *state_info)

  This is an optional hook that platforms can implement in order
  to perform accounting after exiting from a low power state.  This
  typically involves capturing a timestamp.

* u_register_t plat_psci_stat_get_residency(unsigned int lvl,
	const psci_power_state_t *state_info,
	unsigned int last_cpu_index)

  This is an optional hook that platforms can implement in order
  to calculate the PSCI stat residency.

If any of these interfaces are overridden by the platform, it is
recommended that all of them are.

By default `ENABLE_PSCI_STAT` is disabled.  If `ENABLE_PSCI_STAT`
is set but `ENABLE_PMF` is not set then an alternative PSCI stat
collection backend must be provided.  If both are set, then default
weak definitions of these functions are provided, using PMF to
calculate the residency.

NOTE: Previously, platforms did not have to explicitly set
`ENABLE_PMF` since this was automatically done by the top-level
Makefile.

Change-Id: I17b47804dea68c77bc284df15ee1ccd66bc4b79b
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

Replace all use of memset by zeromem when zeroing moderately-sized
structure by applying the following transformation:
memset(x, 0, sizeof(x)) => zeromem(x, sizeof(x))

As the Trusted Firmware is compiled with -ffreestanding, it forbids the
compiler from using __builtin_memset and forces it to generate calls to
the slow memset implementation. Zeromem is a near drop in replacement
for this use case, with a more efficient implementation on both AArch32
and AArch64.

Change-Id: Ia7f3a90e888b96d056881be09f0b4d65b41aa79e
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

One nasty part of ATF is some of boolean macros are always defined
as 1 or 0, and the rest of them are only defined under certain
conditions.

For the former group, "#if FOO" or "#if !FOO" must be used because
"#ifdef FOO" is always true.  (Options passed by $(call add_define,)
are the cases.)

For the latter, "#ifdef FOO" or "#ifndef FOO" should be used because
checking the value of an undefined macro is strange.

For AARCH32/AARCH64, these macros are defined in the top-level
Makefile as follows:

ifeq (${ARCH},aarch32)
        $(eval $(call add_define,AARCH32))
else
        $(eval $(call add_define,AARCH64))
endif

This means only one of the two is defined.  So, AARCH32/AARCH64
belongs to the latter group where we should use #ifdef or #ifndef.
The conditionals are mostly coded correctly, but I see some mistakes.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

One nasty part of ATF is some of boolean macros are always defined
as 1 or 0, and the rest of them are only defined under certain
conditions.

For the former group, "#if FOO" or "#if !FOO" must be used because
"#ifdef FOO" is always true.  (Options passed by $(call add_define,)
are the cases.)

For the latter, "#ifdef FOO" or "#ifndef FOO" should be used because
checking the value of an undefined macro is strange.

Here, IMAGE_BL* is handled by make_helpers/build_macro.mk like
follows:

  $(eval IMAGE := IMAGE_BL$(call uppercase,$(3)))

  $(OBJ): $(2)
          @echo "  CC      $$<"
          $$(Q)$$(CC) $$(TF_CFLAGS) $$(CFLAGS) -D$(IMAGE) -c $$< -o $$@

This means, IMAGE_BL* is defined when building the corresponding
image, but *undefined* for the other images.

So, IMAGE_BL* belongs to the latter group where we should use #ifdef
or #ifndef.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

We have lots of duplicated defines (and comment blocks too).
Move them to include/plat/common/common_def.h.

While we are here, suffix the end address with _END instead of
_LIMIT.  The _END is a better fit to indicate the linker-derived
real end address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The usage of _LIMIT seems odd here, so rename as follows:
  BL_CODE_LIMIT     --> BL_CODE_END
  BL_RO_DATA_LIMIT  --> BL_RO_DATA_END
  BL1_CODE_LIMIT    --> BL1_CODE_END
  BL1_RO_DATA_LIMIT --> BL1_RO_DATA_END

Basically, we want to use _LIMIT and _END properly as follows:
  *_SIZE + *_MAX_SIZE = *_LIMIT
  *_SIZE + *_SIZE     = *_END

The _LIMIT is generally defined by platform_def.h to indicate the
platform-dependent memory constraint.  So, its typical usage is
  ASSERT(. <= BL31_LIMIT, "BL31 image has exceeded its limit.")
in a linker script.

On the other hand, _END is used to indicate the end address of the
compiled image, i.e. we do not know it until the image is linked.

Here, all of these macros belong to the latter, so should be
suffixed with _END.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Before adding a base address and a size to compute the end
address of an image to copy or authenticate, check this
won't result in an integer overflow. If it does then consider
the input arguments are invalid.

As a result, bl1_plat_mem_check() can now safely assume the
end address (computed as the sum of the base address and size
of the memory region) doesn't overflow, as the validation is
done upfront in bl1_fwu_image_copy/auth(). A debug assertion
has been added nonetheless in the ARM implementation in order
to help catching such problems, should bl1_plat_mem_check()
be called in a different context in the future.

Fixes TFV-1: Malformed Firmware Update SMC can result in copy
of unexpectedly large data into secure memory

Change-Id: I8b8f8dd4c8777705722c7bd0e8b57addcba07e25
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Signed-off-by: Dan Handley <dan.handley@arm.com>

ASM_ASSERT failure and panic messages are suppressed at present. This
patch enables printing the PC location for panic messages, and file name
and line number upon assembly assert failure.

Change-Id: I80cb715988e7ce766f64da1e1d7065a74a096a0c
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The previous code required that a certificate be signed with the ROT
key before the platform's NV counter could be updated with the value
in the certificate.  This implies that the Non-Trusted NV counter was
not being updated for Non-Trusted content certificates, as they cannot
be signed with the ROT key in the TBBR CoT scheme.

The code is reworked to only allow updating the platform's Trusted NV
counter when a certificate protected by the Trusted NV counter is
signed with the ROT key.

Content certificates protected by the Non-Trusted NV counter are
allowed to update the platform's Non-Trusted NV counter, assuming
that the certificate value is higher than the platform's value.

A new optional platform API has been introduced, named
plat_set_nv_ctr2().  Platforms may choose to implement it and perform
additional checks based on the authentication image descriptor before
modifying the NV counters.  A default weak implementation is available
that just calls into plat_set_nv_ctr().

Fixes ARM-software/tf-issues#426

Change-Id: I4fc978fd28a3007bc0cef972ff1f69ad0413b79c
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

As with other ARM platform GIC APIs, these directly invoke the GICv3
driver APIs for Redistributor power management.

For the sake of uniform GIC API, empty stubs are placed for those GIC
drivers that lack Redistributor component.

Change-Id: Iad0d760d4dbca790998f7768cda621ff3b15a864
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

This patch enables TRUSTED_BOARD_BOOT (Authentication and FWU)
support, for AArch64, when LOAD_IMAGE_V2 is enabled.

This patch also enables LOAD_IMAGE_V2 for ARM platforms.

Change-Id: I294a2eebce7a30b6784c80c9d4ac7752808ee3ad
Signed-off-by: Yatharth Kochar <yatharth.kochar@arm.com>

The capabilities exposed by the PSCI generic layer depends on the hooks
populated by the platform in `plat_arm_psci_pm_ops`. Currently ARM
Standard platforms statically define this structure. However, some
platforms may want to modify the hooks at runtime before registering
them with the generic layer.

This patch introduces a new ARM platform layer API
`plat_arm_psci_override_pm_ops` which allows the platform to probe
the power controller and modify `plat_arm_psci_pm_ops` if required.
Consequently, 'plat_arm_psci_pm_ops' is no longer qualified as
`const` on ARM Standard platforms.

Change-Id: I7dbb44b7bd36c20ec14ded5ee45a96816ca2ab9d
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Add dependency information in the user guide for ARM_RECOM_STATE_ID_ENC
that needs to be set when using PSCI_EXTENDED_STATE_ID on ARM
platforms. Also clarify the build error message.

Change-Id: Id125a0299b179f5f222bca4e2503204bf89a3c59
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

This patch adds ARM SiP service for use by ARM standard platforms.
This service is added to support the SMC interface for the Performance
measurement framework(PMF).

Change-Id: I26f5712f9ab54f5f721dd4781e35a16f40aacc44
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

This patch adds support in SP_MIN to receive generic and
platform specific arguments from BL2.

The new signature is as following:
    void sp_min_early_platform_setup(void *from_bl2,
         void *plat_params_from_bl2);

ARM platforms have been modified to use this support.

Note: Platforms may break if using old signature.
      Default value for RESET_TO_SP_MIN is changed to 0.

Change-Id: I008d4b09fd3803c7b6231587ebf02a047bdba8d0

This patch adds ARM platform changes in BL2 for AArch32 state.
It instantiates a descriptor array for ARM platforms describing
image and entrypoint information for `SCP_BL2`, `BL32` and `BL33`.
It also enables building of BL2 for ARCH=aarch32.

Change-Id: I60dc7a284311eceba401fc789311c50ac746c51e

This patch adds ARM platform changes in BL1 for AArch32 state.
It also enables building of BL1 for ARCH=aarch32.

Change-Id: I079be81a93d027f37b0f7d8bb474b1252bb4cf48

This patch adds changes in ARM platform code to use new
version of image loading.

Following are the major changes:
  -Refactor the signatures for bl31_early_platform_setup()
   and arm_bl31_early_platform_setup() function to use
   `void *` instead of `bl31_params_t *`.
  -Introduce `plat_arm_bl2_handle_scp_bl2()` to handle
   loading of SCP_BL2 image from BL2.
  -Remove usage of reserve_mem() function from
   `arm_bl1_early_platform_setup()`
  -Extract BL32 & BL33 entrypoint info, from the link list
   passed by BL2, in `arm_bl31_early_platform_setup()`
  -Provides weak definitions for following platform functions:
     plat_get_bl_image_load_info
     plat_get_next_bl_params
     plat_flush_next_bl_params
     bl2_plat_handle_post_image_load
  -Instantiates a descriptor array for ARM platforms
   describing image and entrypoint information for
   `SCP_BL2`, `BL31`, `BL32` and `BL33` images.

All the above changes are conditionally compiled using the
`LOAD_IMAGE_V2` flag.

Change-Id: I5e88b9785a3df1a2b2bbbb37d85b8e353ca61049

This patch implements the support for SP_MIN in FVP. The SP_MIN platform
APIs are implemented and the required makefile support is added for FVP.

Change-Id: Id50bd6093eccbd5e38894e3fd2b20d5baeac5452

This patch adds AArch32 support for FVP and implements common platform APIs
like `plat_get_my_stack`, `plat_set_my_stack`, `plat_my_core_cos` for AArch32.
Only Multi Processor(MP) implementations of these functions are considered in
this patch. The ARM Standard platform layer helpers are implemented for
AArch32 and the common makefiles are modified to cater for both AArch64 and
AArch32 builds. Compatibility with the deprecated platform API is not
supported for AArch32.

Change-Id: Iad228400613eec91abf731b49e21a15bcf2833ea

Previously the definition of `plat_get_syscnt_freq2()` in `arm_common.c` was
conditionally defined based on the ERROR_DEPRECATED flag. This patch makes
this function available irrespective of the flag and removes the deprecated
`plat_get_syscnt_freq()` definition.

Change-Id: I250ca787ca1b5e867096c6ba8f2bb444db44c97b

The PRELOADED_BL33_BASE build option allows to preload a BL33 and bypass its
loading by BL2. In ARM standard platforms, the conditional behaviour of
PRELOADED_BL33_BASE is moved within the implementation of
`plat_get_ns_image_entrypoint()` so that all callers may benefit from this
feature.

Change-Id: Iea060e204ec72f8081087837854535c4e320da4e

This patch moves the `arm_common.c` file from `plat/arm/common/aarch64/`
to the parent directory since the functions implemented in the file are
not AArch64 specific. The platform makefiles are also modified for this
change.

Change-Id: I776d2e4958f59041476cf2f53a9adb5b2d304ee0

The `plat_psci_common.c` was moved to the new location `plat/common`
and a stub file was retained at previous location for compatibility. This
patch modifies the platform makefiles to include the file from the new
location.

Change-Id: Iabddeeb824e9a5d72d176d7c644735966c8c0699

This patch reworks type usage in generic code, drivers and ARM platform files
to make it more portable. The major changes done with respect to
type usage are as listed below:

* Use uintptr_t for storing address instead of uint64_t or unsigned long.
* Review usage of unsigned long as it can no longer be assumed to be 64 bit.
* Use u_register_t for register values whose width varies depending on
  whether AArch64 or AArch32.
* Use generic C types where-ever possible.

In addition to the above changes, this patch also modifies format specifiers
in print invocations so that they are AArch64/AArch32 agnostic. Only files
related to upcoming feature development have been reworked.

Change-Id: I9f8c78347c5a52ba7027ff389791f1dad63ee5f8

This patch adds some verbose traces in the arm_setup_page_tables()
function to print the extents of the different memory regions it maps.

Change-Id: Ia3ae1053e7ebf3579601ff9238b0e3791eb1e9e4

The arm_setup_page_tables() function used to expect a single set of
addresses defining the extents of the whole read-only section, code
and read-only data mixed up, which was mapped as executable.

This patch changes this behaviour. arm_setup_page_tables() now
expects 2 separate sets of addresses:

 - the extents of the code section;
 - the extents of the read-only data section.

The code is mapped as executable, whereas the data is mapped as
execute-never. New #defines have been introduced to identify the
extents of the code and the read-only data section. Given that
all BL images except BL1 share the same memory layout and linker
script structure, these #defines are common across these images.
The slight memory layout differences in BL1 have been handled by
providing values specific to BL1.

Note that this patch also affects the Xilinx platform port, which
uses the arm_setup_page_tables() function. It has been updated
accordingly, such that the memory mappings on this platform are
unchanged. This is achieved by passing null values as the extents
of the read-only data section so that it is ignored. As a result,
the whole read-only section is still mapped as executable.

Fixes ARM-software/tf-issues#85

Change-Id: I1f95865c53ce6e253a01286ff56e0aa1161abac5

This patch changes the base address of the "total" Trusted SRAM region
seen by the BL2U image. It used to start just after BL2U's read-only
section (i.e. at address BL2U_RO_LIMIT), it now starts from the base
address of the BL2U image (i.e. at address BL2U_BASE). In other words,
the "total" memory region now includes BL2U's own read-only section.

This does not change BL2U's resulting memory mappings because the
read-only section was already mapped in BL2U, it just wasn't part of
this total memory region.

Change-Id: I2da16ac842469023b41904eaa8d13ed678d65671

At the moment, on ARM platforms, BL1 maps everything from BL1_RO_BASE
to BL1_RO_LIMIT. BL1_RO_LIMIT, as defined in the porting guide, is
the maximum address in Trusted ROM that BL1's actual content _can_
occupy. The actual portion of ROM occupied by BL1 can be less than
that, which means that BL1 might map more Trusted ROM than it actually
needs to.

This patch changes BL1's memory mappings on ARM platforms to restrict
the region of Trusted ROM it maps. It uses the symbols exported by
the linker to figure out the actual extents of BL1's ROM footprint.

This change increases the number of page tables used on FVP by 1.
On FVP, we used to map the whole Trusted ROM. As it is 64MB large,
we used to map it as blocks of 2MB using level-2 translation table
entries. We now need a finer-grained mapping, which requires an
additional level-3 translation table.

On ARM CSS platforms, the number of translation tables is unchanged.
The BL1 image resides in flash at address 0x0BEC0000. This address is
not aligned on a 2MB-boundary so a level-3 translation table was
already required to map this memory.

Change-Id: I317a93fd99c40e70d0f13cc3d7a570f05c6c61eb

This patch introduces a new header file: include/lib/utils.h.
Its purpose is to provide generic macros and helper functions that
are independent of any BL image, architecture, platform and even
not specific to Trusted Firmware.

For now, it contains only 2 macros: ARRAY_SIZE() and
IS_POWER_OF_TWO(). These were previously defined in bl_common.h and
xlat_tables.c respectively.

bl_common.h includes utils.h to retain compatibility for platforms
that relied on bl_common.h for the ARRAY_SIZE() macro. Upstream
platform ports that use this macro have been updated to include
utils.h.

Change-Id: I960450f54134f25d1710bfbdc4184f12c049a9a9