GitLab

This way it can be reused by other platforms if needed.

Note that this driver is designed to work with the Versatile Express NOR
flash of Juno and FVP. In said platforms, the memory is organized as an
interleaved memory of two chips with a 16 bit word.

Any platform that wishes to reuse it with a different configuration will
need to modify the driver so that it is more generic.

Change-Id: Ic721758425864e0cf42b7b9b04bf0d9513b6022e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The patch 7b56928a

 unified the FWU mechanism on FVP and Juno
platforms due to issues with MCC firmware not preserving the
NVFLAGS. With MCCv150 firmware, this issue is resolved. Also
writing to the NOR flash while executing from the same flash
in Bypass mode had some stability issues. Hence, since the
MCC firmware issue is resolved, this patch reverts to the
NVFLAGS mechanism to detect FWU. Also, with the introduction
of SDS (Shared Data Structure) by the SCP, the reset syndrome
needs to queried from the appropriate SDS field.

Change-Id: If9c08f1afaaa4fcf197f3186887068103855f554
Signed-off-by: Sathees Balya <sathees.balya@arm.com>
Signed-off-by: Soby Mathew <Soby.Mathew@arm.com>

The board_arm_def.h header file needs to be included via the platform
definition header. Not doing so, results in a redefinition error of
PLAT_ARM_MAX_BL31_SIZE macro, if defined in the platform definition
file.

Change-Id: I1d178f6e8a6a41461e7fbcab9f6813a2faa2d82b
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>

Previously, Juno used to depend on the SSC_GPRETN register to inform
about the reset syndrome. This method was removed when SCP migrated
to the SDS framework. But even the SDS framework doesn't report the
reset syndrome correctly and hence Juno failed to enter Firmware
update mode if BL2 authentication failed.

In addition to that, the error code populated in V2M_SYS_NVFLAGS register
does not seem to be retained any more on Juno across resets. This could
be down to the motherboard firmware not doing the necessary to preserve
the value.

Hence this patch modifies the Juno platform to use the same mechanism to
trigger firmware update as FVP which is to corrupt the FIP TOC on
authentication failure. The implementation in `fvp_err.c` is made common
for ARM platforms and is moved to the new `arm_err.c` file in
plat/arm/common folder. The BL1 and BL2 mmap table entries for Juno
are modified to allow write to the Flash memory address.

Change-Id: Ica7d49a3e8a46a90efd4cf340f19fda3b549e945
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Rule 8.4: A compatible declaration shall be visible when
          an object or function with external linkage is defined

Fixed for:
	make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all

Change-Id: I7c2ad3f5c015411c202605851240d5347e4cc8c7
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/



Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

This patch adds a WFI instruction in the default implementations of
plat_error_handler() and plat_panic_handler(). This potentially reduces
power consumption by allowing the hardware to enter a low-power state.
The same change has been made to the FVP and Juno platform ports.

Change-Id: Ia4e6e1e5bf1ed42efbba7d0ebbad7be8d5f9f173

This patch adds watchdog support on ARM platforms (FVP and Juno).
A secure instance of SP805 is used as Trusted Watchdog. It is
entirely managed in BL1, being enabled in the early platform setup
hook and disabled in the exit hook. By default, the watchdog is
enabled in every build (even when TBB is disabled).

A new ARM platform specific build option `ARM_DISABLE_TRUSTED_WDOG`
has been introduced to allow the user to disable the watchdog at
build time. This feature may be used for testing or debugging
purposes.

Specific error handlers for Juno and FVP are also provided in this
patch. These handlers will be called after an image load or
authentication error. On FVP, the Table of Contents (ToC) in the FIP
is erased. On Juno, the corresponding error code is stored in the
V2M Non-Volatile flags register. In both cases, the CPU spins until
a watchdog reset is generated after 256 seconds (as specified in
the TBBR document).

Change-Id: I9ca11dcb0fe15af5dbc5407ab3cf05add962f4b4

This patch adds the missing features to the C library included
in the Trusted Firmware to build PolarSSL:

  - strcasecmp() function
  - exit() function
  - sscanf()* function
  - time.h header file (and its dependencies)

* NOTE: the sscanf() function is not a real implementation. It just
returns the number of expected arguments by counting the number of
'%' characters present in the formar string. This return value is
good enough for PolarSSL because during the certificate parsing
only the return value is checked. The certificate validity period
is ignored.

Change-Id: I43bb3742f26f0bd458272fccc3d72a7f2176ab3d

This patch adds a tool that generates all the necessary elements
to establish the chain of trust (CoT) between the images.

The tool reads the binary images and signing keys and outputs the
corresponding certificates that will be used by the target at run
time to verify the authenticity of the images.

Note: the platform port must provide the file platform_oid.h. This
file will define the OIDs of the x509 extensions that will be added
to the certificates in order to establish the CoT.

Change-Id: I2734d6808b964a2107ab3a4805110698066a04be

This patch implements the TSP on Juno. It executes from on-chip Trusted
SRAM.

Also, the other bootloader images (i.e. BL1 R/W, BL2 and BL3-1) have
been moved around. The reason is, although there was enough space
overall to store the TSP in SRAM, there was no contiguous free chunk
of SRAM big enough to hold it.

This patch keeps the overall memory layout (i.e. keeping BL1 R/W at
the bottom, BL2 at the top and BL3-1 in between) but moves the base
addresses of all the bootloader images in such a way that:
 - memory fragmentation is reduced enough to fit BL3-2 in;
 - new base addresses are suitable for release builds as well as debug
   ones;
 - each image has a few extra kilobytes for future growth.
   BL3-1 and BL3-2 are the images which received the biggest allocations
   since they will most probably grow the most.

This patch also adds instruction synchronization barriers around the code which
handles the timer interrupt in the TSP. This ensures that the interrupt is not
acknowledged after or EOIed before it is deactivated at the peripheral.

Change-Id: I1c5b51858700027ee283ac85d18e06863a27c72e

This patch adds the initial port of the ARM Trusted Firmware on the Juno
development platform. This port does not support a BL3-2 image or any PSCI APIs
apart from PSCI_VERSION and PSCI_CPU_ON. It enables workarounds for selected
Cortex-A57 (#806969 & #813420) errata and implements the workaround for a Juno
platform errata (Defect id 831273).

Change-Id: Ib3d92df3af53820cfbb2977582ed0d7abf6ef893

Move the remaining IO storage source file (io_storage.c) from the
lib to the drivers directory. This requires that platform ports
explicitly add this file to the list of source files.

Also move the IO header files to a new sub-directory, include/io.

Change-Id: I862b1252a796b3bcac0d93e50b11e7fb2ded93d6

Update code base to remove variables from the .data section,
mainly by using const static data where possible and adding
the const specifier as required. Most changes are to the IO
subsystem, including the framework APIs. The FVP power
management code is also affected.

Delay initialization of the global static variable,
next_image_type in bl31_main.c, until it is realy needed.
Doing this moves the variable from the .data to the .bss
section.

Also review the IO interface for inconsistencies, using
uintptr_t where possible instead of void *. Remove the
io_handle and io_dev_handle typedefs, which were
unnecessary, replacing instances with uintptr_t.

Fixes ARM-software/tf-issues#107.

Change-Id: I085a62197c82410b566e4698e5590063563ed304

Reduce the number of header files included from other header
files as much as possible without splitting the files. Use forward
declarations where possible. This allows removal of some unnecessary
"#ifndef __ASSEMBLY__" statements.

Also, review the .c and .S files for which header files really need
including and reorder the #include statements alphabetically.

Fixes ARM-software/tf-issues#31

Change-Id: Iec92fb976334c77453e010b60bcf56f3be72bd3e

Move almost all system include files to a logical sub-directory
under ./include. The only remaining system include directories
not under ./include are specific to the platform. Move the
corresponding source files to match the include directory
structure.

Also remove pm.h as it is no longer used.

Change-Id: Ie5ea6368ec5fad459f3e8a802ad129135527f0b3

The modified implementation uses the IO abstraction rather than
making direct semi-hosting calls.  The semi-hosting driver is now
registered for the FVP platform during initialisation of each boot
stage where it is used.  Additionally, the FVP platform includes a
straightforward implementation of 'plat_get_image_source' which
provides a generic means for the 'load_image' function to determine
how to access the image data.

Change-Id: Ia34457b471dbee990c7b3c79de7aee4ceea51aa6

Ctags seem to have a problem with generating tags for assembler symbols
when a comment immediately follows an assembly label.

This patch inserts a single space character between the label
definition and the following comments to help ctags.

The patch is generated by the command:

  git ls-files -- \*.S | xargs sed -i 's/^\([^:]\+\):;/\1: ;/1'

Change-Id: If7a3c9d0f51207ea033cc8b8e1b34acaa0926475

Change-Id: Ic7fb61aabae1d515b9e6baf3dd003807ff42da60

- Add instructions for contributing to ARM Trusted Firmware.

- Update copyright text in all files to acknowledge contributors.

Change-Id: I9311aac81b00c6c167d2f8c889aea403b84450e5