GitLab

A previous patch superseded the MBEDTLS_KEY_ALG. This patch updates
the ARM platforms to use the new TF_MBEDTLS_KEY_ALG define.

Change-Id: Ie0e1bc272e127e879ac58e7cfcbe268751d7688e
Signed-off-by: David Cunado <david.cunado@arm.com>

In AArch64, privileged exception levels control the execution state
(a.k.a. register width) of the immediate lower Exception Level; i.e.
whether the lower exception level executes in AArch64 or AArch32 state.
For an exception level to have its execution state changed at run time,
it must request the change by raising a synchronous exception to the
higher exception level.

This patch implements and adds such a provision to the ARM SiP service,
by which an immediate lower exception level can request to switch its
execution state. The execution state is switched if the request is:

  - raised from non-secure world;

  - raised on the primary CPU, before any secondaries are brought online
    with CPU_ON PSCI call;

  - raised from an exception level immediately below EL3: EL2, if
    implemented; otherwise NS EL1.

If successful, the SMC doesn't return to the caller, but to the entry
point supplied with the call. Otherwise, the caller will observe the SMC
returning with STATE_SW_E_DENIED code. If ARM Trusted Firmware is built
for AArch32, the feature is not supported, and the call will always
fail.

For the ARM SiP service:

  - Add SMC function IDs for both AArch32 and AArch64;
  - Increment the SiP service minor version to 2;
  - Adjust the number of supported SiP service calls.

Add documentation for ARM SiP service.

Fixes ARM-software/tf-issues#436

Change-Id: I4347f2d6232e69fbfbe333b340fcd0caed0a4cea
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/



Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

Following steps are required to boot JUNO in AArch32 state:
1> BL1, in AArch64 state, loads BL2.
2> BL2, in AArch64 state, initializes DDR.
  Loads SP_MIN & BL33 (AArch32 executable)images.
  Calls RUN_IMAGE SMC to go back to BL1.
3> BL1 writes AArch32 executable opcodes, to load and branch
  at the entrypoint address of SP_MIN, at HI-VECTOR address and
  then request for warm reset in AArch32 state using RMR_EL3.

This patch makes following changes to facilitate above steps:
* Added assembly function to carry out step 3 above.
* Added region in TZC that enables Secure access to the
  HI-VECTOR(0xFFFF0000) address space.
* AArch32 image descriptor is used, in BL2, to load
  SP_MIN and BL33 AArch32 executable images.

A new flag `JUNO_AARCH32_EL3_RUNTIME` is introduced that
controls above changes. By default this flag is disabled.

NOTE: BL1 and BL2 are not supported in AArch32 state for JUNO.

Change-Id: I091d56a0e6d36663e6d9d2bb53c92c672195d1ec
Signed-off-by: Yatharth Kochar <yatharth.kochar@arm.com>
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

ARM platforms have migrated to the translation tables library v2.
However, for testing purposes, it can be useful to temporarily switch
back to the old version.

This patch introduces the option `ARM_XLAT_TABLES_LIB_V1`, that switches
to v1 of the library when is set to 1. By default, it is 0, so that ARM
platforms use the new version unless specifically stated.

Updated User Guide.

Change-Id: I53d3c8dd97706f6af9c6fca0364a88ef341efd31
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch modifies some of the functions in ARM platform layer to cater
for the case when multi-threading `MT` is set in MPIDR. A new build flag
`ARM_PLAT_MT` is added, and when enabled, the functions accessing MPIDR
now assume that the `MT` bit is set for the platform and access the bit
fields accordingly.

Also, a new API plat_arm_get_cpu_pe_count is added when `ARM_PLAT_MT` is
enabled, returning the PE count within the physical cpu corresponding to
`mpidr`.

Change-Id: I04ccf212ac3054a60882761f4087bae299af13cb
Signed-off-by: Summer Qin <summer.qin@arm.com>

These source file definitions should be defined in generic
Makefiles so that all platforms can benefit. Ensure that the
symbols are properly marked as weak so they can be overridden
by platforms.

NOTE: This change is a potential compatibility break for
non-upstream platforms.

Change-Id: I7b892efa9f2d6d216931360dc6c436e1d10cffed
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

Modify ARM common makefile to use version 2 of the translation tables
library and include the new header in C files.

Simplify header dependencies related to this library to simplify the
change.

The following table contains information about the size increase in
bytes for BL1 after applying this patch. The code has been compiled for
different configurations of FVP in AArch64 mode with compiler GCC 4.9.3
20150413. The sizes have been calculated with the output of `nm` by
adding the size of all regions and comparing the total size before and
after the change. They are sumarized in the table below:

                               text   bss   data  total
        Release                +660   -20    +88   +728
        Debug                  +740   -20   +242   +962
        Debug (LOG_LEVEL=50)  +1120   -20   +317  +1417

Change-Id: I539e307f158ab71e3a8b771640001fc1bf431b29
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch introduces the following three platform interfaces:

* void plat_psci_stat_accounting_start(const psci_power_state_t *state_info)

  This is an optional hook that platforms can implement in order
  to perform accounting before entering a low power state.  This
  typically involves capturing a timestamp.

* void plat_psci_stat_accounting_stop(const psci_power_state_t *state_info)

  This is an optional hook that platforms can implement in order
  to perform accounting after exiting from a low power state.  This
  typically involves capturing a timestamp.

* u_register_t plat_psci_stat_get_residency(unsigned int lvl,
	const psci_power_state_t *state_info,
	unsigned int last_cpu_index)

  This is an optional hook that platforms can implement in order
  to calculate the PSCI stat residency.

If any of these interfaces are overridden by the platform, it is
recommended that all of them are.

By default `ENABLE_PSCI_STAT` is disabled.  If `ENABLE_PSCI_STAT`
is set but `ENABLE_PMF` is not set then an alternative PSCI stat
collection backend must be provided.  If both are set, then default
weak definitions of these functions are provided, using PMF to
calculate the residency.

NOTE: Previously, platforms did not have to explicitly set
`ENABLE_PMF` since this was automatically done by the top-level
Makefile.

Change-Id: I17b47804dea68c77bc284df15ee1ccd66bc4b79b
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

The previous code required that a certificate be signed with the ROT
key before the platform's NV counter could be updated with the value
in the certificate.  This implies that the Non-Trusted NV counter was
not being updated for Non-Trusted content certificates, as they cannot
be signed with the ROT key in the TBBR CoT scheme.

The code is reworked to only allow updating the platform's Trusted NV
counter when a certificate protected by the Trusted NV counter is
signed with the ROT key.

Content certificates protected by the Non-Trusted NV counter are
allowed to update the platform's Non-Trusted NV counter, assuming
that the certificate value is higher than the platform's value.

A new optional platform API has been introduced, named
plat_set_nv_ctr2().  Platforms may choose to implement it and perform
additional checks based on the authentication image descriptor before
modifying the NV counters.  A default weak implementation is available
that just calls into plat_set_nv_ctr().

Fixes ARM-software/tf-issues#426

Change-Id: I4fc978fd28a3007bc0cef972ff1f69ad0413b79c
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

This patch enables TRUSTED_BOARD_BOOT (Authentication and FWU)
support, for AArch64, when LOAD_IMAGE_V2 is enabled.

This patch also enables LOAD_IMAGE_V2 for ARM platforms.

Change-Id: I294a2eebce7a30b6784c80c9d4ac7752808ee3ad
Signed-off-by: Yatharth Kochar <yatharth.kochar@arm.com>

Add dependency information in the user guide for ARM_RECOM_STATE_ID_ENC
that needs to be set when using PSCI_EXTENDED_STATE_ID on ARM
platforms. Also clarify the build error message.

Change-Id: Id125a0299b179f5f222bca4e2503204bf89a3c59
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

This patch adds ARM SiP service for use by ARM standard platforms.
This service is added to support the SMC interface for the Performance
measurement framework(PMF).

Change-Id: I26f5712f9ab54f5f721dd4781e35a16f40aacc44
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

This patch adds ARM platform changes in BL2 for AArch32 state.
It instantiates a descriptor array for ARM platforms describing
image and entrypoint information for `SCP_BL2`, `BL32` and `BL33`.
It also enables building of BL2 for ARCH=aarch32.

Change-Id: I60dc7a284311eceba401fc789311c50ac746c51e

This patch adds ARM platform changes in BL1 for AArch32 state.
It also enables building of BL1 for ARCH=aarch32.

Change-Id: I079be81a93d027f37b0f7d8bb474b1252bb4cf48

This patch adds changes in ARM platform code to use new
version of image loading.

Following are the major changes:
  -Refactor the signatures for bl31_early_platform_setup()
   and arm_bl31_early_platform_setup() function to use
   `void *` instead of `bl31_params_t *`.
  -Introduce `plat_arm_bl2_handle_scp_bl2()` to handle
   loading of SCP_BL2 image from BL2.
  -Remove usage of reserve_mem() function from
   `arm_bl1_early_platform_setup()`
  -Extract BL32 & BL33 entrypoint info, from the link list
   passed by BL2, in `arm_bl31_early_platform_setup()`
  -Provides weak definitions for following platform functions:
     plat_get_bl_image_load_info
     plat_get_next_bl_params
     plat_flush_next_bl_params
     bl2_plat_handle_post_image_load
  -Instantiates a descriptor array for ARM platforms
   describing image and entrypoint information for
   `SCP_BL2`, `BL31`, `BL32` and `BL33` images.

All the above changes are conditionally compiled using the
`LOAD_IMAGE_V2` flag.

Change-Id: I5e88b9785a3df1a2b2bbbb37d85b8e353ca61049

This patch adds AArch32 support for FVP and implements common platform APIs
like `plat_get_my_stack`, `plat_set_my_stack`, `plat_my_core_cos` for AArch32.
Only Multi Processor(MP) implementations of these functions are considered in
this patch. The ARM Standard platform layer helpers are implemented for
AArch32 and the common makefiles are modified to cater for both AArch64 and
AArch32 builds. Compatibility with the deprecated platform API is not
supported for AArch32.

Change-Id: Iad228400613eec91abf731b49e21a15bcf2833ea

This patch moves the `arm_common.c` file from `plat/arm/common/aarch64/`
to the parent directory since the functions implemented in the file are
not AArch64 specific. The platform makefiles are also modified for this
change.

Change-Id: I776d2e4958f59041476cf2f53a9adb5b2d304ee0

The `plat_psci_common.c` was moved to the new location `plat/common`
and a stub file was retained at previous location for compatibility. This
patch modifies the platform makefiles to include the file from the new
location.

Change-Id: Iabddeeb824e9a5d72d176d7c644735966c8c0699

The arm_setup_page_tables() function used to expect a single set of
addresses defining the extents of the whole read-only section, code
and read-only data mixed up, which was mapped as executable.

This patch changes this behaviour. arm_setup_page_tables() now
expects 2 separate sets of addresses:

 - the extents of the code section;
 - the extents of the read-only data section.

The code is mapped as executable, whereas the data is mapped as
execute-never. New #defines have been introduced to identify the
extents of the code and the read-only data section. Given that
all BL images except BL1 share the same memory layout and linker
script structure, these #defines are common across these images.
The slight memory layout differences in BL1 have been handled by
providing values specific to BL1.

Note that this patch also affects the Xilinx platform port, which
uses the arm_setup_page_tables() function. It has been updated
accordingly, such that the memory mappings on this platform are
unchanged. This is achieved by passing null values as the extents
of the read-only data section so that it is ignored. As a result,
the whole read-only section is still mapped as executable.

Fixes ARM-software/tf-issues#85

Change-Id: I1f95865c53ce6e253a01286ff56e0aa1161abac5

This patch enables optional PSCI functions `PSCI_STAT_COUNT` and
`PSCI_STAT_RESIDENCY` for ARM standard platforms. The optional platform
API 'translate_power_state_by_mpidr()' is implemented for the Juno
platform. 'validate_power_state()' on Juno downgrades PSCI CPU_SUSPEND
requests for the system power level to the cluster power level.
Hence, it is not suitable for validating the 'power_state' parameter
passed in a PSCI_STAT_COUNT/RESIDENCY call.

Change-Id: I9548322676fa468d22912392f2325c2a9f96e4d2

This patch modifies the upstream platform port makefiles to use the new
xlat_tables library files. This patch also makes mmap region setup common
between AArch64 and AArch32 for FVP platform port. The file `fvp_common.c`
is moved from the `plat/arm/board/fvp/aarch64` folder to the parent folder
as it is not specific to AArch64.

Change-Id: Id2e9aac45e46227b6f83cccfd1e915404018ea0b

This patch adds an option to the ARM common platforms to load BL31 in the
TZC secured DRAM instead of the default secure SRAM.

To enable this feature, set `ARM_BL31_IN_DRAM` to 1 in build options.
If TSP is present, then setting this option also sets the TSP location
to DRAM and ignores the `ARM_TSP_RAM_LOCATION` build flag.

To use this feature, BL2 platform code must map in the DRAM used by
BL31. The macro ARM_MAP_BL31_SEC_DRAM is provided for this purpose.
Currently, only the FVP BL2 platform code maps in this DRAM.

Change-Id: If5f7cc9deb569cfe68353a174d4caa48acd78d67

This patch fixes inconsistencies in bl1_tbbr_image_descs[]
and miscellaneous fixes in Firmware Update code.

Following are the changes:
* As part of the original FWU changes, a `copied_size`
  field was added to `image_info_t`. This was a subtle binary
  compatibility break because it changed the size of the
  `bl31_params_t` struct, which could cause problems if
  somebody used different versions of BL2 or BL31, one with
  the old `image_info_t` and one with the new version.
  This patch put the `copied_size` within the `image_desc_t`.
* EXECUTABLE flag is now stored in `ep_info.h.attr` in place
  of `image_info.h.attr`, associating it to an entrypoint.
* The `image_info.image_base` is only relevant for secure
  images that are copied from non-secure memory into secure
  memory. This patch removes initializing `image_base` for
  non secure images in the bl1_tbbr_image_descs[].
* A new macro `SET_STATIC_PARAM_HEAD` is added for populating
  bl1_tbbr_image_descs[].ep_info/image_info.h members statically.
  The version, image_type and image attributes are now
  populated using this new macro.
* Added PLAT_ARM_NVM_BASE and PLAT_ARM_NVM_SIZE to avoid direct
  usage of V2M_FLASH0_XXX in plat/arm/common/arm_bl1_fwu.c.
* Refactoring of code/macros related to SECURE and EXECUTABLE flags.

NOTE: PLATFORM PORTS THAT RELY ON THE SIZE OF `image_info_t`
      OR USE the "EXECUTABLE" BIT WITHIN `image_info_t.h.attr`
      OR USE THEIR OWN `image_desc_t` ARRAY IN BL1, MAY BE
      BROKEN BY THIS CHANGE. THIS IS CONSIDERED UNLIKELY.

Change-Id: Id4e5989af7bf0ed263d19d3751939da1169b561d

ARM Trusted Firmware supports 2 different interconnect peripheral
drivers: CCI and CCN. ARM platforms are implemented using either of the
interconnect peripherals.

This patch adds a layer of abstraction to help ARM platform ports to
choose the right interconnect driver and corresponding platform support.
This is as described below:

1. A set of ARM common functions have been implemented to initialise an
interconnect and for entering/exiting a cluster from coherency. These
functions are prefixed as "plat_arm_interconnect_". Weak definitions of
these functions have been provided for each type of driver.

2.`plat_print_interconnect_regs` macro used for printing CCI registers is
moved from a common arm_macros.S to cci_macros.S.

3. The `ARM_CONFIG_HAS_CCI` flag used in `arm_config_flags` structure
is renamed to `ARM_CONFIG_HAS_INTERCONNECT`.

Change-Id: I02f31184fbf79b784175892d5ce1161b65a0066c

Prior to this patch, it was assumed that on all ARM platforms the bare
minimal security setup required is to program TrustZone protection. This
would always be done by programming the TZC-400 which was assumed to be
present in all ARM platforms. The weak definition of
platform_arm_security_setup() in plat/arm/common/arm_security.c
reflected these assumptions.

In reality, each ARM platform either decides at runtime whether
TrustZone protection needs to be programmed (e.g. FVPs) or performs
some security setup in addition to programming TrustZone protection
(e.g. NIC setup on Juno). As a result, the weak definition of
plat_arm_security_setup() is always overridden.

When a platform needs to program TrustZone protection and implements the
TZC-400 peripheral, it uses the arm_tzc_setup() function to do so. It is
also possible to program TrustZone protection through other peripherals
that include a TrustZone controller e.g. DMC-500. The programmer's
interface is slightly different across these various peripherals.

In order to satisfy the above requirements, this patch makes the
following changes to the way security setup is done on ARM platforms.

1. arm_security.c retains the definition of arm_tzc_setup() and has been
   renamed to arm_tzc400.c. This is to reflect the reliance on the
   TZC-400 peripheral to perform TrustZone programming. The new file is
   not automatically included in all platform ports through
   arm_common.mk. Each platform must include it explicitly in a platform
   specific makefile if needed.

   This approach enables introduction of similar library code to program
   TrustZone protection using a different peripheral. This code would be
   used by the subset of ARM platforms that implement this peripheral.

2. Due to #1 above, existing platforms which implements the TZC-400 have been
   updated to include the necessary files for both BL2, BL2U and BL31
   images.

Change-Id: I513c58f7a19fff2e9e9c3b95721592095bcb2735

Currently, Trusted Firmware on ARM platforms unlocks access to the
timer frame registers that will be used by the Non-Secure world. This
unlock operation should be done by the Non-Secure software itself,
instead of relying on secure firmware settings.

This patch adds a new ARM specific build option 'ARM_CONFIG_CNTACR'
to unlock access to the timer frame by setting the corresponding
bits in the CNTACR<N> register. The frame id <N> is defined by
'PLAT_ARM_NSTIMER_FRAME_ID'. Default value is true (unlock timer
access).

Documentation updated accordingly.

Fixes ARM-software/tf-issues#170

Change-Id: Id9d606efd781e43bc581868cd2e5f9c8905bdbf6

The fip_create tool specifies images in the command line using the
ARM TF naming convention (--bl2, --bl31, etc), while the cert_create
tool uses the TBBR convention (--tb-fw, --soc-fw, etc). This double
convention is confusing and should be aligned.

This patch updates the fip_create command line options to follow the
TBBR naming convention. Usage examples in the User Guide have been
also updated.

NOTE: users that build the FIP by calling the fip_create tool directly
from the command line must update the command line options in their
scripts. Users that build the FIP by invoking the main ARM TF Makefile
should not notice any difference.

Change-Id: I84d602630a2585e558d927b50dfde4dd2112496f

Firmware update feature needs a new FIP called `fwu_fip.bin` that
includes Secure(SCP_BL2U, BL2U) and Normal world(NS_BL2U) images
along with the FWU_CERT certificate in order for NS_BL1U to load
the images and help the Firmware update process to complete.

This patch adds the capability to support the new target `fwu_fip`
which includes above mentioned FWU images in the make files.

The new target of `fwu_fip` and its dependencies are included for
compilation only when `TRUSTED_BOARD_BOOT` is defined.

Change-Id: Ie780e3aac6cbd0edfaff3f9af96a2332bd69edbc

This patch adds support for Firmware update in BL2U for ARM
platforms such that TZC initialization is performed on all
ARM platforms and (optionally) transfer of SCP_BL2U image on
ARM CSS platforms.

BL2U specific functions are added to handle early_platform and
plat_arch setup. The MMU is configured to map in the BL2U
code/data area and other required memory.

Change-Id: I57863295a608cc06e6cbf078b7ce34cbd9733e4f

This patch adds Firmware Update support for ARM platforms.

New files arm_bl1_fwu.c and juno_bl1_setup.c were added to provide
platform specific Firmware update code.

BL1 now includes mmap entry for `ARM_MAP_NS_DRAM1` to map DRAM for
authenticating NS_BL2U image(For both FVP and JUNO platform).

Change-Id: Ie116cd83f5dc00aa53d904c2f1beb23d58926555

Suport for ARM GIC v2.0 and v3.0 drivers has been reworked to create three
separate drivers instead of providing a single driver that can work on both
versions of the GIC architecture. These drivers correspond to the following
software use cases:

1. A GICv2 only driver that can run only on ARM GIC v2.0 implementations
   e.g. GIC-400

2. A GICv3 only driver that can run only on ARM GIC v3.0 implementations
   e.g. GIC-500 in a mode where all interrupt regimes use GICv3 features

3. A deprecated GICv3 driver that operates in legacy mode. This driver can
   operate only in the GICv2 mode in the secure world. On a GICv3 system, this
   driver allows normal world to run in either GICv3 mode (asymmetric mode)
   or in the GICv2 mode. Both modes of operation are deprecated on GICv3
   systems.

ARM platforms implement both versions of the GIC architecture. This patch adds a
layer of abstraction to help ARM platform ports chose the right GIC driver and
corresponding platform support. This is as described below:

1. A set of ARM common functions have been introduced to initialise the GIC and
   the driver during cold and warm boot. These functions are prefixed as
   "plat_arm_gic_". Weak definitions of these functions have been provided for
   each type of driver.

2. Each platform includes the sources that implement the right functions
   directly into the its makefile. The FVP can be instantiated with different
   versions of the GIC architecture. It uses the FVP_USE_GIC_DRIVER build option
   to specify which of the three drivers should be included in the build.

3. A list of secure interrupts has to be provided to initialise each of the
  three GIC drivers. For GIC v3.0 the interrupt ids have to be further
  categorised as Group 0 and Group 1 Secure interrupts. For GIC v2.0, the two
  types are merged and treated as Group 0 interrupts.

  The two lists of interrupts are exported from the platform_def.h. The lists
  are constructed by adding a list of board specific interrupt ids to a list of
  ids common to all ARM platforms and Compute sub-systems.

This patch also makes some fields of `arm_config` data structure in FVP redundant
and these unused fields are removed.

Change-Id: Ibc8c087be7a8a6b041b78c2c3bd0c648cd2035d8

This patch adds watchdog support on ARM platforms (FVP and Juno).
A secure instance of SP805 is used as Trusted Watchdog. It is
entirely managed in BL1, being enabled in the early platform setup
hook and disabled in the exit hook. By default, the watchdog is
enabled in every build (even when TBB is disabled).

A new ARM platform specific build option `ARM_DISABLE_TRUSTED_WDOG`
has been introduced to allow the user to disable the watchdog at
build time. This feature may be used for testing or debugging
purposes.

Specific error handlers for Juno and FVP are also provided in this
patch. These handlers will be called after an image load or
authentication error. On FVP, the Table of Contents (ToC) in the FIP
is erased. On Juno, the corresponding error code is stored in the
V2M Non-Volatile flags register. In both cases, the CPU spins until
a watchdog reset is generated after 256 seconds (as specified in
the TBBR document).

Change-Id: I9ca11dcb0fe15af5dbc5407ab3cf05add962f4b4

This patch adds support for booting EL3 payloads on CSS platforms,
for example Juno. In this scenario, the Trusted Firmware follows
its normal boot flow up to the point where it would normally pass
control to the BL31 image. At this point, it jumps to the EL3
payload entry point address instead.

Before handing over to the EL3 payload, the data SCP writes for AP
at the beginning of the Trusted SRAM is restored, i.e. we zero the
first 128 bytes and restore the SCP Boot configuration. The latter
is saved before transferring the BL30 image to SCP and is restored
just after the transfer (in BL2). The goal is to make it appear that
the EL3 payload is the first piece of software to run on the target.

The BL31 entrypoint info structure is updated to make the primary
CPU jump to the EL3 payload instead of the BL31 image.

The mailbox is populated with the EL3 payload entrypoint address,
which releases the secondary CPUs out of their holding pen (if the
SCP has powered them on). The arm_program_trusted_mailbox() function
has been exported for this purpose.

The TZC-400 configuration in BL2 is simplified: it grants secure
access only to the whole DRAM. Other security initialization is
unchanged.

This alternative boot flow is disabled by default. A new build option
EL3_PAYLOAD_BASE has been introduced to enable it and provide the EL3
payload's entry point address. The build system has been modified
such that BL31 and BL33 are not compiled and/or not put in the FIP in
this case, as those images are not used in this boot flow.

Change-Id: Id2e26fa57988bbc32323a0effd022ab42f5b5077

This patch adds a device driver which can be used to program the following
aspects of ARM CCN IP:

1. Specify the mapping between ACE/ACELite/ACELite+DVM/CHI master interfaces and
   Request nodes.
2. Add and remove master interfaces from the snoop and dvm
   domains.
3. Place the L3 cache in a given power state.
4. Configuring system adress map and enabling 3 SN striping mode of memory
   controller operation.

Change-Id: I0f665c6a306938e5b66f6a92f8549b529aa8f325

This patch adds support to the Juno and FVP ports for composite power states
with both the original and extended state-id power-state formats. Both the
platform ports use the recommended state-id encoding as specified in
Section 6.5 of the PSCI specification (ARM DEN 0022C). The platform build flag
ARM_RECOM_STATE_ID_ENC is used to include this support.

By default, to maintain backwards compatibility, the original power state
parameter format is used and the state-id field is expected to be zero.

Change-Id: Ie721b961957eaecaca5bf417a30952fe0627ef10

This patch migrates ARM reference platforms, Juno and FVP, to the new platform
API mandated by the new PSCI power domain topology and composite power state
frameworks. The platform specific makefiles now exports the build flag
ENABLE_PLAT_COMPAT=0 to disable the platform compatibility layer.

Change-Id: I3040ed7cce446fc66facaee9c67cb54a8cd7ca29

This patch modifies the Trusted Board Boot implementation to use
the new authentication framework, making use of the authentication
module, the cryto module and the image parser module to
authenticate the images in the Chain of Trust.

A new function 'load_auth_image()' has been implemented. When TBB
is enabled, this function will call the authentication module to
authenticate parent images following the CoT up to the root of
trust to finally load and authenticate the requested image.

The platform is responsible for picking up the right makefiles to
build the corresponding cryptographic and image parser libraries.
ARM platforms use the mbedTLS based libraries.

The platform may also specify what key algorithm should be used
to sign the certificates. This is done by declaring the 'KEY_ALG'
variable in the platform makefile. FVP and Juno use ECDSA keys.

On ARM platforms, BL2 and BL1-RW regions have been increased 4KB
each to accommodate the ECDSA code.

REMOVED BUILD OPTIONS:

  * 'AUTH_MOD'

Change-Id: I47d436589fc213a39edf5f5297bbd955f15ae867

This patch adds a CoT based on the Trusted Board Boot Requirements
document*. The CoT consists of an array of authentication image
descriptors indexed by the image identifiers.

A new header file with TBBR image identifiers has been added.
Platforms that use the TBBR (i.e. ARM platforms) may reuse these
definitions as part of their platform porting.

PLATFORM PORT - IMPORTANT:

Default image IDs have been removed from the platform common
definitions file (common_def.h). As a consequence, platforms that
used those common definitons must now either include the IDs
provided by the TBBR header file or define their own IDs.

*The NVCounter authentication method has not been implemented yet.

Change-Id: I7c4d591863ef53bb0cd4ce6c52a60b06fa0102d5

This major change pulls out the common functionality from the
FVP and Juno platform ports into the following categories:

*   (include/)plat/common. Common platform porting functionality that
typically may be used by all platforms.

*   (include/)plat/arm/common. Common platform porting functionality
that may be used by all ARM standard platforms. This includes all
ARM development platforms like FVP and Juno but may also include
non-ARM-owned platforms.

*   (include/)plat/arm/board/common. Common platform porting
functionality for ARM development platforms at the board
(off SoC) level.

*   (include/)plat/arm/css/common. Common platform porting
functionality at the ARM Compute SubSystem (CSS) level. Juno
is an example of a CSS-based platform.

*   (include/)plat/arm/soc/common. Common platform porting
functionality at the ARM SoC level, which is not already defined
at the ARM CSS level.

No guarantees are made about the backward compatibility of
functionality provided in (include/)plat/arm.

Also remove any unnecessary variation between the ARM development
platform ports, including:

*   Unify the way BL2 passes `bl31_params_t` to BL3-1. Use the
Juno implementation, which copies the information from BL2 memory
instead of expecting it to persist in shared memory.

*   Unify the TZC configuration. There is no need to add a region
for SCP in Juno; it's enough to simply not allow any access to
this reserved region. Also set region 0 to provide no access by
default instead of assuming this is the case.

*   Unify the number of memory map regions required for ARM
development platforms, although the actual ranges mapped for each
platform may be different. For the FVP port, this reduces the
mapped peripheral address space.

These latter changes will only be observed when the platform ports
are migrated to use the new common platform code in subsequent
patches.

Change-Id: Id9c269dd3dc6e74533d0e5116fdd826d53946dc8