GitLab

This patch migrates the upstream platform makefiles to include the
console drivers from the new location in ARM Trusted Firmware code
base.

Change-Id: I866d6c4951e475de1f836ce8a8c1d5e6da9577e3

1. Remove the AP_PWROFF in ATF, should configure it in kernel.
2. Save and restore the PWMs pin/regs for suspend/resume.
3. The pmusgrf reset-hold bits needs to be released. since the
   pmusgrf reset-hold bits needs to be held.
4. Configure the PMU power up/down cycles about delay 3ms.
5. With the MMIO register block as one big mapping.
6. Fix the build error with psci_entrypoint since PSCI lib updated.

Fixes the commit
9ec78bdf ("rockchip: support the suspend/resume for rk3399").

Change-Id: I112806700bf433c87763aac23d22fa7e6a7f5264

The `plat_psci_common.c` was moved to the new location `plat/common`
and a stub file was retained at previous location for compatibility. This
patch modifies the platform makefiles to include the file from the new
location.

Change-Id: Iabddeeb824e9a5d72d176d7c644735966c8c0699

1.Fixes the suspend/resume some bugs.
2.Add the power domain for saving power consumption.
3.Add cpu clusters suspend for rk3399 SoCs

Change-Id: Id602779016b41d6281f4ba40a20229d909b28e46

Software executing in the normal world and in the trusted world at
exception levels lower than EL3 will request runtime services using the
SMC instruction.

See the documentation here:
https://github.com/ARM-software/arm-trusted-firmware/blob/master/docs/
rt-svc-writers-guide.md

This to be implemented as an EL3 Runtime Service in rockchip BL31
platform port, using the "SiP Service Call" range as specified in the
SMC Calling Convention.
This doesn't support any SMC yet, we will support it in later.

Change-Id: I0a638dd0b653c28b08f79d89f77ed7c69864017d

This patch introduces a new header file: include/lib/utils.h.
Its purpose is to provide generic macros and helper functions that
are independent of any BL image, architecture, platform and even
not specific to Trusted Firmware.

For now, it contains only 2 macros: ARRAY_SIZE() and
IS_POWER_OF_TWO(). These were previously defined in bl_common.h and
xlat_tables.c respectively.

bl_common.h includes utils.h to retain compatibility for platforms
that relied on bl_common.h for the ARRAY_SIZE() macro. Upstream
platform ports that use this macro have been updated to include
utils.h.

Change-Id: I960450f54134f25d1710bfbdc4184f12c049a9a9

if define power off gpio, BL31 will do system power off through
gpio control.

If define a reset gpio, BL31 will use gpio to reset SOC,
otherwise use CRU reset.

We add plat parameter structs to support BL2 to pass variable-length,
variable-type parameters to BL31. The parameters are structured as a
link list. During bl31 setup time, we travse the list to process each
parameter. throuth this way, we can get the reset or power off gpio
parameter, and do hardware control in BL31. This structure also can
pass other parameter to BL31 in future.

There are 5 groups of GPIO (GPIO0~GPIO4), totally have 122 GPIOs
on rk3399 platform.
The pull direction(pullup or pulldown) for all of GPIOs are
software-programmable.
At the moment, we add the gpio basic driver since reset or power off
the devices from gpio configuration for BL31.

Use the generic delay timer instead of having a specific platform
file for configuring it.

Change-Id: Ifa68b9c97cd96ae1190cee74d22d729af95e4537

Replaced plat_get_syscnt_freq by plat_get_syscnt_freq2 on all
upstream platforms.

Change-Id: I3248f3f65a16dc5e9720012a05c35b9e3ba6abbe

This patch adds some debug assertions ensuring that array indices
are within the bounds of the array.

Change-Id: I96ee81d14834c1e92cdfb7e60b49995cdacfd93a

This patch adds to support the suspend/resume for rk3399 SoCs.
Signed-off-by: Shengfei xu <xsf@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>

This patch has the following change for rk3399.

* Set the uart to 115200 since the loader decide to set
  uart baud to 115200Hz. So the ATF also should set uart baud to 115200.

* We need ensure the bl31 base is greater than 4KB since there are have
  the shared mem for coreboot.(Note: the previous vesion was tested with uboot)

Otherwise, we will happen the exception crash since the ddr area won't
to work from the shared ram address in some cases.

For example, the exception crash:
CBFS: Found @ offset 19c80 size 24074
exception _sync_sp_el0
ELR = 0x0000000000008000
ESR = 0x0000000002000000
SPSR = 0x600003cc
FAR = 0xffffffff00000000
SP = 0x00000000ff8ed230
...
X29 = 0x00000000ff8c1fc0
X30 = 0x000000000030e3b0
exception death

Change-Id: I8bc557c6bcaf6804d2a313b38667d3e2517881d7
Signed-off-by: Caesar Wang <wxt@rock-chips.com>

This patch moves the definition for `plat_get_syscnt_freq()`
from arm_bl31_setup.c to arm_common.c. This could be useful
in case a delay timer needs to be installed based on the
generic timer in other BLs.
This patch also modifies the return type for this function
from `uint64_t` to `unsigned long long` within ARM and other
platform files.

Change-Id: Iccdfa811948e660d4fdcaae60ad1d700e4eda80d

It is up to the platform to implement the new plat_crash_print_regs macro to
report all relevant platform registers helpful for troubleshooting.

plat_crash_print_regs merges or calls previously defined plat_print_gic_regs
and plat_print_interconnect_regs macros for each existing platforms.

NOTE: THIS COMMIT REQUIRES ALL PLATFORMS THAT ENABLE THE `CRASH_REPORTING`
BUILD FLAG TO MIGRATE TO USE THE NEW `plat_crash_print_regs()` MACRO. BY
DEFAULT, `CRASH_REPORTING` IS ENABLED IN DEBUG BUILDS FOR ALL PLATFORMS.

Fixes: arm-software/tf-issues#373
Signed-off-by: Gerald Lejeune <gerald.lejeune@st.com>

This patch modifies the upstream platform port makefiles to use the new
xlat_tables library files. This patch also makes mmap region setup common
between AArch64 and AArch32 for FVP platform port. The file `fvp_common.c`
is moved from the `plat/arm/board/fvp/aarch64` folder to the parent folder
as it is not specific to AArch64.

Change-Id: Id2e9aac45e46227b6f83cccfd1e915404018ea0b

This patch fixes the compilation error in Rockchip rk3368 platform port when
it is built in release mode.

Fixes ARM-software/tf-issues#389

Change-Id: I1a3508ac3a620289cf700e79db8f08569331ac53

This patch adds to support the RK3368 and RK3399 SoCs.

RK3368/RK3399 is one of the Rockchip family SoCs, which is an
multi-cores ARM SoCs.

This patch adds support to boot the Trusted Firmware on RK3368/RK3399
SoCs, and adds support to boot secondary CPUs, enter/exit core
power states for all CPUs in the slow/fast clusters.

This is the initial version for rockchip SoCs.(RK3368/RK3399 and next SoCs)
* Support arm gicv2 & gicv3.
* Boot up multi-cores CPU.
* Add generic CPU helper functions.
* Support suspend/resume.
* Add system_off & system_reset implementation.
* Add delay timer platform implementation.
* Support the new porting interface for the PSCI implementation.

Change-Id: I704bb3532d65e8c70dbd99b512c5e6e440ea6f43
Signed-off-by: Tony Xie <tony.xie@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Shengfei xu <xsf@rock-chips.com>