GitLab

The only difference between GIC-500 and GIC-600 relevant to TF-A is the
differing power management sequence.
A certain GIC implementation is detectable at runtime, for instance by
checking the IIDR register. Let's add that test before initiating the
GIC-600 specific sequence, so the code can be used on both GIC-600 and
GIC-500 chips alike, without deciding on a GIC chip at compile time.

This means that the GIC-500 "driver" is now redundant. To allow minimal
platform support, add a switch to disable GIC-600 support.

Change-Id: I17ea97d9fb05874772ebaa13e6678b4ba3415557
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

This patch moves all GICv3 driver files into new added
'gicv3.mk' makefile for the benefit of the generic driver
which can evolve in the future without affecting platforms.
The patch adds GICv3 driver configuration flags
'GICV3_IMPL', 'GICV3_IMPL_GIC600_MULTICHIP' and
'GICV3_OVERRIDE_DISTIF_PWR_OPS' described in
'GICv3 driver options' section of 'build-option.rst'
document.

NOTE: Platforms with GICv3 driver need to be modified to
include 'drivers/arm/gic/v3/gicv3.mk' in their makefiles.

Change-Id: If055f6770ff20f5dee5a3c99ae7ced7cdcac5c44
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

Since N1SDP has a system level cache which is an
external LLC enable the NEOVERSE_N1_EXTERNAL_LLC flag.

Change-Id: Idb34274e61e7fd9db5485862a0caa497f3e290c7
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>

This patch provides separation of GICD, GICR accessor
functions and adds new macros for GICv3 registers access
as a preparation for GICv3.1 and GICv4 support.
NOTE: Platforms need to modify to include both
'gicdv3_helpers.c' and 'gicrv3_helpers.c' instead of the
single helper file previously.

Change-Id: I1641bd6d217d6eb7d1228be3c4177b2d556da60a
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

N1SDP supports multichip configuration wherein n1sdp boards are
connected over high speed coherent CCIX link, for now only dual-chip
is supported.

Whether or not multiple chips are present is dynamically probed by
SCP firmware and passed on to TF-A, routing table will be set up
only if multiple chips are present.

Initialize GIC-600 multichip operation by overriding the default GICR
frames with array of GICR frames and setting the chip 0 as routing
table owner.

Change-Id: Ida35672be4bbf4c517469a5b330548d75e593ff2
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>

N1SDP platform supports RDIMMs with ECC capability. To use the ECC
capability, the entire DDR memory space has to be zeroed out before
enabling the ECC bits in DMC620. Zeroing out several gigabytes of
memory from SCP is quite time consuming so functions are added that
zeros out the DDR memory from application processor which is
much faster compared to SCP. BL33 binary cannot be copied to DDR memory
before enabling ECC so this is also done by TF-A from IOFPGA-DDR3
memory to main DDR4 memory after ECC is enabled.

Original PLAT_PHY_ADDR_SPACE_SIZE was limited to 36-bits with which
the entire DDR space cannot be accessed as DRAM2 starts in base
0x8080000000. So these macros are redefined for all ARM platforms.

Change-Id: If09524fb65b421b7a368b1b9fc52c49f2ddb7846
Signed-off-by: Manoj Kumar <manoj.kumar3@arm.com>

The BL1 stage setup code for ARM platforms sets up the SP805 watchdog
controller as the secure watchdog. But not all ARM platforms use SP805
as the secure watchdog controller.

So introduce two new ARM platform code specific wrapper functions to
start and stop the secure watchdog. These functions then replace the
calls to SP805 driver in common BL1 setup code. All the ARM platforms
implement these wrapper functions by either calling into SP805 driver
or the SBSA watchdog driver.

Change-Id: I1a9a11b124cf3fac2a84f22ca40acd440a441257
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

Change-Id: Ideb49011da35f39ff1959be6f5015fa212ca2b6b
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

This patch removes the dependency of the N1SDP on soc
css defines in order to let the N1SDP platform port
define the uart related constants.

Change-Id: If13796f278586a01512ee99615502b30e478189e
Signed-off-by: Deepak Pandey <Deepak.Pandey@arm.com>

This patch adds support for the N1SDP (NeoVerse N1 System Development
Platform). It is an initial port and additional features are expected
to be added later.

The port includes only BL31 support as the System Control Processor
(SCP) is expected to take the role of primary boatloader

Change-Id: Ife17d8215a7bfcc1420204a72205e7ef920d0c10
Signed-off-by: Deepak Pandey <Deepak.Pandey@arm.com>