GitLab

Added smc calls support to access ddr phy registers.

Change-Id: Ibaa0a8e20b6398ab394c7e2e9ea61f9a28cdb870
Signed-off-by: Alex Leibovich <alexl@marvell.com>
Reviewed-on: https://sj1git1.cavium.com/20791

Tested-by: Kostya Porotchkin <kostap@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

Since more drivers which uses dfx register set need to be handled with
use of SiP services, use dedicated and more meaningful name for thermal
SiP services.

Change-Id: Ic2ac27535a4902477df8edc4c86df3e34cb2344f
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-on: https://sj1git1.cavium.com/25054

Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

Since the dfx register set is going to be marked as secure (in order to
protect efuse registers for non secure access), accessing thermal
registers which are part of dfx register set, will not be possible from
lower exception levels. Due to above expose thermal driver as a SiP
service.  This will allow Linux and U-Boot thermal driver to initialise
and perform various operations on thermal sensor.

The thermal sensor driver is based on Linux
drivers/thermal/armada_thermal.c.

Change-Id: I4763a3bf5c43750c724c86b1dcadad3cb729e93e
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-on: https://sj1git1.cavium.com/20581

Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Tested-by: Kostya Porotchkin <kostap@marvell.com>

Wrong brakets caused MSS FW load timeout error:
ERROR:   MSS DMA failed (timeout)
ERROR:   MSS FW chunk 0 load failed
ERROR:   SCP Image load failed

This patch fixes the operator precedence in MSS FW load.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Change-Id: I78c215606bde112f40429926c51f5fa1e4334c13

The number of ITS have changed from 4 to 1, resulting
in GICR base address change.
Signed-off-by: Usama Arif <usama.arif@arm.com>
Change-Id: I28101f0d1faf9f3c58591b642033c3fd49a275e7

NT_FW_CONFIG file is meant to be passed from BL31 to be consumed by
BL33, fvp platforms use this to pass measured boot configuration and
the x0 register is used to pass the base address of it.

In case of hafnium used as hypervisor in normal world, hypervisor
manifest is expected to be passed from BL31 and its base address is
passed in x0 register.

As only one of NT_FW_CONFIG or hypervisor manifest base address can be
passed in x0 register and also measured boot is not required for SPM so
disable passing NT_FW_CONFIG.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ifad9d3658f55ba7d70f468a88997d5272339e53e

Create a dedicated static struct mmc_device_info mmc_info mmc_info
instead of having this in stack.
A boot issue has been seen on some platform when applying patch [1].

 [1] 13f3c516

 ("mmc:prevent accessing to the released space in case of wrong usage")
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: I73a079715253699d903721c865d6470d58f6bd30

Create a dedicated static struct mmc_device_info mmc_info mmc_info
instead of having this in stack.
A boot issue has been seen on some platform when applying patch [1].

 [1] 13f3c516

 ("mmc:prevent accessing to the released space in case of wrong usage")
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: Id52c0be61a30f453a551385883eaf3cbe32b04b9

Create a dedicated static struct mmc_device_info mmc_info mmc_info
instead of having this in stack.
A boot issue has been seen on some platform when applying patch [1].

 [1] 13f3c516

 ("mmc:prevent accessing to the released space in case of wrong usage")
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: If5db8857cccec2e677b16a38eb3eeb41628a264c

Refine the function plat_add_sp_images_load_info() by saving the
previous node and only setting its next link when the current node is
valid. This can reduce the check for the next node and simply the
total logic.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: I4061428bf49ef0c3816ac22aaeb2e50315531f88

The traverse flow in function plat_add_sp_images_load_info() will find
the last node in the main load info list, with its
next_load_info==NULL. However this node is still useful and should not
be overridden with SP node info.

The bug will cause below error on RDN2 for spmd enabled:

ERROR:   Invalid NT_FW_CONFIG DTB passed

Fix the bug by only setting the next_load_info of the last node in the
original main node list.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: Icaee5da1f2d53b29fdd6085a8cc507446186fd57

As per the new multi-console framework, updating the JTAG DCC support.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: I77994ce387caf0d695986df3d01d414a920978d0

As per the new multi-console framework, updating the JTAG DCC support.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: I62cfbb57ae7e454fbc91d1c54aafa6e99f9a35c8

Add basic support for Cortex_A78C CPU.
Signed-off-by: Bipin Ravi <bipin.ravi@arm.com>
Change-Id: Id9e41cbe0580a68c6412d194a5ee67940e8dae56

Add the secure partition mmap table and the secure partition boot
information to support secure partitions on RD-N2 platform. In addition
to this, add the required memory region mapping for accessing the
SoC peripherals from the secure partition.
Signed-off-by: Omkar Anand Kulkarni <omkar.kulkarni@arm.com>
Change-Id: I2c75760d6c8c3da3ff4885599be420e924aeaf3c

A TZC400 controller is placed inline on DRAM channels and regulates
the secure and non-secure accesses to both secure and non-secure
regions of the DRAM memory. Configure each of the TZC controllers
across the Chips.

For use by secure software, configure the first chip's trustzone
controller to protect the upper 16MB of the memory of the first DRAM
block for secure accesses only. The other regions are configured for
non-secure read write access. For all the remote chips, all the DRAM
regions are allowed for non-secure read and write access.
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Change-Id: I809f27eccadfc23ea0ef64e2fd87f95eb8f195c1

On a multi-chip platform, the boot CPU on the first chip programs the
TZC controllers on all the remote chips. Define a memory region map for
the TZC controllers for all the remote chips and include it in the BL2
memory map table.

In addition to this, for SPM_MM enabled multi-chip platforms, increase
the number of mmap entries and xlat table counts for EL3 execution
context as well because the shared RAM regions and GIC address space of
remote chips are accessed.
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Change-Id: I6f0b5fd22f9f28046451e382eef7f1f9258d88f7

For multi-chip platforms, add a macro to define the memory regions on
chip numbers >1 and its associated access permissions. These memory
regions are marked with non-secure access.
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Change-Id: If3d6180fd8ea61f45147c39d3140d694abf06617

Allow the access of system registers and nor2 flash memory region
from s-el0. This allows the secure parititions residing at s-el0
to access these memory regions.
Signed-off-by: Thomas Abraham <thomas.abraham@arm.com>
Change-Id: I3887a86770de806323fbde0d20fdc96eec6e0c3c

Define a default DMC-620 TZC memory region configuration and use it to
specify the TZC memory regions on sgi575, rdn1edge and rde1edge
platforms. The default DMC-620 TZC memory regions are defined
considering the support for secure paritition as well.
Signed-off-by: Thomas Abraham <thomas.abraham@arm.com>
Change-Id: Iedee3e57d0d3de5b65321444da51ec990d3702db

Remove the 'ARM_' prefix from the macros defining the CPER buffer memory
and replace it with 'CSS_SGI_' prefix. These macros are applicable only
for platforms supported within plat/sgi. In addition to this, ensure
that these macros are defined only if the RAS_EXTENSION build option is
enabled.
Signed-off-by: Thomas Abraham <thomas.abraham@arm.com>
Change-Id: I44df42cded18d9d3a4cb13e5c990e9ab3194daee

The macros defining the SMC function ids for DMC-620 error handling are
listed in the sgi_base_platform_def.h header file. But these macros are
not applicable for all platforms supported under plat/sgi. So move these
macro definitions to sgi_ras.c file in which these are consumed. While
at it, remove the AArch32 and error injection function ids as these are
unused.
Signed-off-by: Thomas Abraham <thomas.abraham@arm.com>
Change-Id: I249b54bf4c1b1694188a1e3b297345b942f16bc9

The macros specific to SDEI defined in the sgi_base_platform_def.h are
not applicable for all the platforms supported by plat/sgi. So refactor
the SDEI specific macros into a new header file and include this file on
only on platforms it is applicable on.
Signed-off-by: Thomas Abraham <thomas.abraham@arm.com>
Change-Id: I0cb7125334f02a21cae1837cdfd765c16ab50bf5

Broadcom I2C controller driver. Follwoing API's are supported:-
- i2c_init() Intialize ethe I2C controller
- i2c_probe()
- i2c_set_bus_speed() Set the I2C bus speed
- i2c_get_bus_speed() Get the current bus speed
- i2c_recv_byte() Receive one byte of data.
- i2c_send_byte() Send one byteof data
- i2c_read_byte() Read single byte of data
- i2c_read() Read multiple bytes of data
- i2c_write_byte Write single byte of data
- i2c_write() Write multiple bytes of data

This driver is verified by reading the DDR SPD data.
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Change-Id: I2d7fe53950e8b12fab19d0293020523ff8b74e13

When the BL31 for the Allwinner H616 runs in DRAM, we need to make sure
we tell the non-secure world about the memory region it uses.

Add a reserved-memory node to the DT, which covers the area that BL31
could occupy. The "no-map" property will prevent OSes from mapping
the area, so there would be no speculative accesses.

Change-Id: I808f3e1a8089da53bbe4fc6435a808e9159831e1
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The new Allwinner H616 SoC lacks the management controller and the secure
SRAM A2, so we need to tweak the memory map quite substantially:
We run BL31 in DRAM. Since the DRAM starts at 1GB, we cannot use our
compressed virtual address space (max 256MB) anymore, so we revert to
the full 32bit VA space and use a flat mapping throughout all of it.

The missing controller also means we need to always use the native PSCI
ops, using the CPUIDLE hardware, as SCPI and suspend depend on the ARISC.

Change-Id: I77169b452cb7f5dc2ef734f3fc6e5d931749141d
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Change-Id: I557fd05401e24204952135cf3ca26479a43ad1f1
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

In preparation for changing the memory map, express the locations of the
various code and data pieces more dynamically, allowing SoCs to override
the memmap later.
Also prepare for the SCP region to become optional.

No functional change.

Change-Id: I7ac01e309be2f23bde2ac2050d8d5b5e3d6efea2
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The code to power the current core off when SCPI is not available is now
different for the two supported SoC families.
To make adding new platforms easier, move sunxi_cpu_power_off_self()
into the SoC directory, so we don't need to carry definitions for both
methods for all SoCs.

On the H6 we just need to trigger the CPUIDLE hardware, so can get rid
of all the code to program the ARISC, which is now only needed for the
A64 version.

Change-Id: Id2a1ac7dcb375e2fd021b441575ce86b4d7edf2c
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

For the existing SoCs we support, we use SEPARATE_NOBITS_REGION, to move
some parts of the data into separate memory regions (to save on the SRAM
A2 we are loaded into).
For the upcoming H616 platform this is of no concern (we run in DRAM),
so make this flag a platform choice instead.

Change-Id: Ic01d49578c6274660f8f112bd23680d3eca3be7a
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The upcoming refactoring to support the new H616 SoCs will push the A64
build over the edge, by using more than the 48KB of SRAM available.

To reduce the code size, set some libfdt options that aim to reduce
sanity checks (for saving code space):
- ASSUME_LATEST: only allow v17 DTBs (as created by dtc)
- ASSUME_NO_ROLLBACK: don't prepare for failed DT additions
- ASSUME_LIBFDT_ORDER: assume sane ordering, as done by dtc

Change-Id: I12c93ec09e7587c5ae71e54947f817c32ce5fd6d
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Add basic support for Makalu ELP processor core.
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: I7b1ddbb8dd43326ecb8ff188f6f8fcf239826a93

New NXP platform lx2160a-qds:
- Based SoC lx2160a
- Board specific tuning for DDR init.
- Board specific Flash details.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I500ddbe9e56c4af5f955da6ecbd4ddc5fbe89a12

New NXP platform lx2160a-rdb(Reference Design Board):
- Based SoC lx2160a
- Board specific tuning for DDR init.
- Board specific Flash details.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I9c10dac9d5e67d44a2d94a7a27812220fdcc6ae3

New NXP platform lx2162aqds:
- Based SoC lx2160a
- Board specific tuning for DDR init.
- Board specific Flash details.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I53bfff85398313082db77c77625cb2d40cd9b1b1

SoC erratas are handled as part of this commit.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I06f7594d19cc7fc89fe036a8a255300458cb36dd

- NXP SoC lx2160a needs additional ddr_fip.bin.

- There are three types of ddr image that can be created:
  -- ddr_fip.mk for creating fip_ddr.bin image for normal boot.
  -- ddr_fip_sb.mk for creating fip_ddr_sec.bin image for NXP CSF based
     CoT/secure boot.
  -- ddr_fip_tbbr.mk for creating fip_ddr_sec.bin image for MBEDTLS
     CoT/secure boot.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I24bff8d489f72da99f64cb79b2114faa9423ce8c

* NXP SoC is 16 A-72 core SoC.
* SoC specific defines are defined in:
  - soc.def
  - soc.h
* Called for BL2 and BL31 setup, SoC specific setup are implemented in:
  - soc.c
* platform specific helper functions implemented at:
  - aarch64/lx2160a_helpers.S
* platform specific functions used by 'plat/nxp/commpon/psci',
  etc. are implemented at:
  - aarch64/lx2160a.S
* platform specific implementation for handling PSCI_SYSTEM_RESET2:
  - aarch64/lx2160a_warm_rst.S
Signed-off-by: rocket <rod.dorris@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: Ib40086f9d9079ed9b22967baff518c6df9f408b8

- Default header files for:
  -- plat/nxp/soc-lxxxx/include/soc.h uses:
	--- soc_default_base_addr.h
        --- soc_default_base_macros.h

  -- plat/nxp/soc-lxxxx/<$PLAT>/platform_def.h uses:
	--- plat_default_def.h: Every macro define can be overidden.

  -- include/common/tbbr/tbbr_img_def.h uses:
	--- plat_tbbr_img_def.h: platform specific new FIP image macros.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: Ic50003e27e87891be3cd18bdb4e14a1c7272d492

For NXP platforms:
- Setup files for BL2 and BL31
- Other supporting files.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I36a1183a0652701bdede9e02d41eb976accbb017