- 18 Jan, 2019 2 commits
-
-
Yann Gautier authored
The drivers are also updated to reflect the changes. Set RCC as non-secure. Change-Id: I568fa1f418355830ad1d4d1cdcdb910fb362231b Signed-off-by: Yann Gautier <yann.gautier@st.com>
-
Yann Gautier authored
This is the correct name of the IP. Rename stm32mp1_pmic files to stm32mp_pmic. Change-Id: I238a7d1f9a1d099daf7788dc9ebbd3146ba2f15f Signed-off-by: Yann Gautier <yann.gautier@st.com>
-
- 07 Jan, 2019 1 commit
-
-
Yann Gautier authored
Instead, only platform_def.h is included. The required files to be included are added in stm32mp1_def.h. Signed-off-by: Yann Gautier <yann.gautier@st.com>
-
- 04 Jan, 2019 1 commit
-
-
Antonio Nino Diaz authored
Enforce full include path for includes. Deprecate old paths. The following folders inside include/lib have been left unchanged: - include/lib/cpus/${ARCH} - include/lib/el3_runtime/${ARCH} The reason for this change is that having a global namespace for includes isn't a good idea. It defeats one of the advantages of having folders and it introduces problems that are sometimes subtle (because you may not know the header you are actually including if there are two of them). For example, this patch had to be created because two headers were called the same way: e0ea0928 ("Fix gpio includes of mt8173 platform to avoid collision."). More recently, this patch has had similar problems: 46f9b2c3 ("drivers: add tzc380 support"). This problem was introduced in commit 4ecca339 ("Move include and source files to logical locations"). At that time, there weren't too many headers so it wasn't a real issue. However, time has shown that this creates problems. Platforms that want to preserve the way they include headers may add the removed paths to PLAT_INCLUDES, but this is discouraged. Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
-
- 14 Dec, 2018 1 commit
-
-
Jeenu Viswambharan authored
The GIC lowest priority values for each world depends on the number of priority values implemented in hardware. These constants currently defined in gic_common.h only meant to enumerate lowest possible architectural values. Since these values are not used in generic code or upstream platforms, and that general use of these constants can be wrong, remove these. Platforms should either define and use these as appropriate, or determine correct values at run time. Change-Id: I3805cea8ceb8a592b9eff681ea1b63b7496cec5f Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
-
- 07 Dec, 2018 1 commit
-
-
Julius Werner authored
console_unregister() has always returned a pointer to the console that was removed on success, not just an integer. Fix the C prototype to match the assembly implementation. Change-Id: Iafc43de0767a5c87c9ae5c3aba53761dd28d51e6 Signed-off-by: Julius Werner <jwerner@chromium.org>
-
- 04 Dec, 2018 2 commits
-
-
Christine Gharzuzi authored
- Update CPU frequency on AP807 to 2GHz for SAR 0x0. - Increase AVS to 0.88V for 2GHz clock Change-Id: Ic945b682ab2f8543e34294bfc56c3eae2c5e0c8e Signed-off-by: Christine Gharzuzi <chrisg@marvell.com> Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
-
Peng Fan authored
Add tzc380 support. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Bai Ping <ping.bai@nxp.com>
-
- 23 Nov, 2018 1 commit
-
-
Pankaj Gupta authored
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
-
- 21 Nov, 2018 1 commit
-
-
Vijayenthiran Subramaniam authored
ARM CoreLink DMC-620 Dynamic Memory Controller includes a TZC controller to setup secure or non-secure regions of DRAM memory. The TZC controller allows to setup upto eight such regions of memory in DRAM. This driver provides helper functions to setup the TZC controller within DMC-620. Change-Id: Iee7692417c2080052bdb7b1c2873a024bc5d1d10 Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
-
- 15 Nov, 2018 3 commits
-
-
Konstantin Porotchkin authored
Migrate Marvell platforms from legacy console API to multi-console API. Change-Id: I647f5f49148b463a257a747af05b5f0c967f267c Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
-
Yann Gautier authored
Signed-off-by: Yann Gautier <yann.gautier@st.com>
-
Yann Gautier authored
Signed-off-by: Yann Gautier <yann.gautier@st.com>
-
- 12 Nov, 2018 1 commit
-
-
Alexei Colin authored
Signed-off-by: Alexei Colin <acolin@isi.edu>
-
- 09 Nov, 2018 2 commits
-
-
Yann Gautier authored
It is already in include/drivers/st/stm32mp1_ddr_helpers.h. Signed-off-by: Yann Gautier <yann.gautier@st.com>
-
Yann Gautier authored
These issues wer found by sparse: drivers/st/clk/stm32mp1_clk.c:1524:19: warning: incorrect type in assignment (different base types) expected restricted fdt32_t const [usertype] *pkcs_cell got unsigned int const [usertype] * plat/st/stm32mp1/plat_image_load.c:13:6: warning: symbol 'plat_flush_next_bl_params' was not declared. Should it be static? plat/st/stm32mp1/plat_image_load.c:21:16: warning: symbol 'plat_get_bl_image_load_info' was not declared. Should it be static? plat/st/stm32mp1/plat_image_load.c:29:13: warning: symbol 'plat_get_next_bl_params' was not declared. Should it be static? plat/st/stm32mp1/bl2_io_storage.c:40:10: warning: symbol 'block_buffer' was not declared. Should it be static? Signed-off-by: Yann Gautier <yann.gautier@st.com>
-
- 08 Nov, 2018 1 commit
-
-
Antonio Nino Diaz authored
All identifiers, regardless of use, that start with two underscores are reserved. This means they can't be used in header guards. The style that this project is now to use the full name of the file in capital letters followed by 'H'. For example, for a file called "uart_example.h", the header guard is UART_EXAMPLE_H. The exceptions are files that are imported from other projects: - CryptoCell driver - dt-bindings folders - zlib headers Change-Id: I50561bf6c88b491ec440d0c8385c74650f3c106e Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
-
- 01 Nov, 2018 1 commit
-
-
Antonio Nino Diaz authored
Change-Id: I33eaee8e7c983b3042635a448cb8d689ea4e3a12 Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
-
- 26 Oct, 2018 1 commit
-
-
Antonio Nino Diaz authored
It has only been tested with a system clock of 24 MHz. It has only been implemented for the multi console API. Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
-
- 23 Oct, 2018 1 commit
-
-
Antonio Nino Diaz authored
The definitions FAIL_CONTROL_*_SHIFT were incorrect, they have been fixed. The types tzc_region_attributes_t and tzc_action_t have been removed and replaced by unsigned int because it is not allowed to do logical operations on enums. Also, fix some address definitions in arm_def.h. Change-Id: Id37941d76883f9fe5045a5f0a4224c133c504d8b Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
-
- 20 Oct, 2018 1 commit
-
-
Andre Przywara authored
The "Reduced Serial Bus" is an Allwinner specific bus, bearing many similarities with I2C. It sports a much higher bus frequency, though, (typically 3 MHz) and requires much less handholding for the typical task of manipulating slave registers (fire-and-forget). On most A64 boards this bus is used to connect the PMIC to the SoC. This driver provides basic primitives to read and write slave registers, it will be later used by the PMIC code. Signed-off-by: Andre Przywara <andre.przywara@arm.com>
-
- 15 Oct, 2018 4 commits
-
-
Yann Gautier authored
Whereas the GPT table is read with io_block, the binaries to be loaded (e.g. BL33) cannot use it, as it is not suitable to read them block by block, or the boot time would be very bad. Signed-off-by: Yann Gautier <yann.gautier@st.com>
-
Yann Gautier authored
This IO is required to read binaries with STM32 header. This header is added with the stm32image tool. Signed-off-by: Yann Gautier <yann.gautier@st.com>
-
Yann Gautier authored
To boot on eMMC or SD-cards, STM32MP1 platform needs: - GPT_IMAGE_ID to read GPT table on those devices - STM32_IMAGE_ID and IO_TYPE_STM32IMAGE to read images with STM32 header - IO_TYPE_MMC to have a IO for MMC devices Signed-off-by: Yann Gautier <yann.gautier@st.com>
-
Yann Gautier authored
This driver is for the STMicroelectronics sdmmc2 IP which is in STM32MP1 SoC. It uses the MMC framework, and can address either eMMC or SD-card. Signed-off-by: Yann Gautier <yann.gautier@st.com>
-
- 11 Oct, 2018 1 commit
-
-
Sathees Balya authored
Change-Id: Ica944acc474a099219d50b041cfaeabd4f3d362f Signed-off-by: Sathees Balya <sathees.balya@arm.com>
-
- 10 Oct, 2018 1 commit
-
-
Antonio Nino Diaz authored
This way it can be reused by other platforms if needed. Note that this driver is designed to work with the Versatile Express NOR flash of Juno and FVP. In said platforms, the memory is organized as an interleaved memory of two chips with a 16 bit word. Any platform that wishes to reuse it with a different configuration will need to modify the driver so that it is more generic. Change-Id: Ic721758425864e0cf42b7b9b04bf0d9513b6022e Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
-
- 28 Sep, 2018 5 commits
-
-
Yann Gautier authored
Respect official response type and update response to follow official specification. All the MMC_RESPONSE_R(_x) are replaced with each corresponding define. Partly revert 2a82a9c9 for dw_mmc.c: Responses R1, R1B and R5 have CRC. Signed-off-by: Lionel Debieve <lionel.debieve@st.com> Signed-off-by: Yann Gautier <yann.gautier@st.com>
-
Antonio Nino Diaz authored
Change-Id: Icd1cdd42afdc78895a9be6c46b414b0a155cfa63 Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
-
Antonio Nino Diaz authored
This driver is deprecated. Change-Id: Ic6e154a5756e779743b17a329eed4570ccc61389 Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
-
Antonio Nino Diaz authored
Change-Id: I9874883ec33dbf293f607f9779d7c56f23cb8023 Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
-
Antonio Nino Diaz authored
Change-Id: I567a406edb090ae9d109382f6874846a79dd7473 Co-authored-by: Roberto Vargas <roberto.vargas@arm.com> Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
-
- 05 Sep, 2018 1 commit
-
-
Icenowy Zheng authored
The Marvell A8K SoCs use the MI2CV IP core from Mentor Graphics, which is also used by Allwinner. As Mentor Graphics allows a lot of customization, the MI2CV in the two SoC families are not compatible, and driver modifications are needed. Extract the common code to a MI2CV driver. Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
-
- 04 Sep, 2018 2 commits
-
-
Jun Nie authored
Add response flag into ID definition so that driver does not need to handle it again. Signed-off-by: Jun Nie <jun.nie@linaro.org> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
-
John Tsichritzis authored
The Mbed TLS drivers, in order to work, need a heap for internal usage. This heap, instead of being directly referenced by the drivers, now it is being accessed indirectly through a pointer. Also, the heap, instead of being part of the drivers, now it is being received through the plat_get_mbedtls_heap() function. This function requests a heap from the current BL image which utilises the Mbed TLS drivers. Those changes create the opportunity for the Mbed TLS heap to be shared among different images, thus saving memory. A default heap implementation is provided but it can be overridden by a platform specific, optimised implemenetation. Change-Id: I286a1f10097a9cdcbcd312201eea576c18d157fa Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>
-
- 03 Sep, 2018 2 commits
-
-
Christine Gharzuzi authored
- add svc configuration according to values burnt to the chip efuse Change-Id: Icf5d7cc41bc09ac2244d0a126106e681afebb064 Signed-off-by: Christine Gharzuzi <chrisg@marvell.com> Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
-
Marcin Wojtas authored
This patch introduces new helper routines that allow configuring the individual IRQs to be edge/level-triggered via GICD_ICFGR registers. This is helpful to modify the default configuration of the non-secure GIC SPI's, which are all set during initialization to be level-sensitive. Change-Id: I23deb4a0381691a686a3cda52405aa1dfd5e56f2 Signed-off-by: Marcin Wojtas <mw@semihalf.com> Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
-
- 30 Aug, 2018 3 commits
-
-
Antonio Nino Diaz authored
Change-Id: Ifdb0ceec19d267b14d796b5d31f08f7342190484 Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
-
Antonio Nino Diaz authored
Change-Id: I2954a99d5b72069bcb7bac9d6926c6209d6ba881 Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
-
Antonio Nino Diaz authored
Change-Id: I6a2adef87c20f9279446a54b7e69618fba3d2a25 Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
-