GitLab

None of the other drivers (Linux, U-Boot, Crust) need to lower the bus
clock frequency to switch the PMIC to RSB mode. That logic is not needed
here, either. The hardware takes care of running this transaction at the
correct bus frequency.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Idcfe933df4da75d5fd5a4f3e362da40ac26bdad1

Current implementation doesn't support change of div1 value if clk
has 2 divisor because div1 clk is the parent of the div2 clk and div2
clk does not have SET_RATE_PARENT flag.
This causes div1 value to be fixed and only value of div2 will be
adjusted according to required clock rate.

Example:
 Consider a case of nand_ref clock which has 2 divisor and 1 mux.
 The frequency of mux clock is 1500MHz and default value of div1 and
 div2 is 15 and 1 respectively. So the final clock will be of 100MHz.
 When driver requests 80MHz for nand_ref clock, clock framework will
 adjust the div2 value to 1 (setting div2 value 2 results final clock
 to 50MHz which is more inaccurate compare to 100Mhz) which results
 final clock to 100MHz.
 Ideally the value of div1 and div2 should be updated to 19 and 1
 respectively so that final clock goes to around 78MHz.

This patch fixes above problem by allowing change in div1 value.
Signed-off-by: Ravi Patel <ravi.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: Ibb98f6748d28653fdd1e59bf433b6a37ce9c1a58

This patches copies only the valid part of string and
avoids filling junk at the end.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: If23772f31f9cf7f5042e8bfc474fbfe77dcd90e7

The primary VM concept is removed from the SPMC.
Update the SPMC manifests with number of Execution Contexts
and SP workspace size for the first Secure Partition (as it
is done for NWd secondary VMs and other SPs).
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I3b9c52666f7dfe74ab1f7d2148ad0070ee44b54e

The chosen node is no longer required as the SPMC implements
a specific boot flow which no longer requires this node.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: Ib566b602a7f83003a1b2d0ba5f6ebf4d8b7a9156

Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I0981c43e2ef8172138f65d95eac7b20f8969394e

The PVM concept is removed from the SPMC so the device-memory
node which is specifying the device memory range for the PVM
is no longer applicable.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: If0cb956e0197028b24ecb78952c66ec454904516

1. Add mcusys related dcm drivers
2. Turn on mcusys-related dcm by default

Change-Id: Ibbee37c87cc38e7a6cd7c93c2fc0817aad6dbe95
Signed-off-by: Nina Wu <nina-cm.wu@mediatek.com>

enable PTP3 for protecting sysPi
Signed-off-by: elly.chiang <elly.chiang@mediatek.com>
Change-Id: Ic3a13c8314f829dca8547861b98639d1d9444eb2

Add the basic SiP service

Change-Id: Ib7f2380aab910adf8d33498a79ecd287273907c5
Signed-off-by: Nina Wu <nina-cm.wu@mediatek.com>

When system resume, we want to print log as soon as possible.
So we add uart save and restore api, and they will be called
when systtem suspend and resume.

Change-Id: I83b477fd2b39567c9c6b70534ef186993f7053ae
Signed-off-by: Yuchen Huang <yuchen.huang@mediatek.com>
Signed-off-by: Roger Lu <roger.lu@mediatek.com>

1.Modify this driver to make it more complete and more standard.
2.And makes this driver available for more IC services.
3.Solve some bugs in the software.
Signed-off-by: G.Pangao <gtk_pangao@mediatek.com>
Change-Id: I284956d47ebbbd550ec93767679181185e442348

add power-off support
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: If19e99971515a8ae1ac9ae21046e4382adc18a69

add pmic mt6359p driver
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: I20f2218f7d2087e8d2bf31258cf92a02e0dab77d

Init delay_timer for the use of delay functions

Change-Id: I35aefd7515bb9259634c8b6bc37d8c74da96e8f1
Signed-off-by: Nina Wu <nina-cm.wu@mediatek.com>

Enable NS access for all systimers.
Signed-off-by: Dehui Sun <dehui.sun@mediatek.com>
Change-Id: I3693997082a1d6f09fef5a79b6cf5a91be46cb8a

Implement PSCI platform OPs to support CPU hotplug and MCDI.

Change-Id: I31abfc752b69ac40e70bc9e7a55163eb39776c44
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>

Add MCDI related drivers to handle CPU powered on/off in CPU suspend.

Change-Id: I5110461e8eef86f8383b45f197ec5cb10dbfeb3e
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>

Add SPMC driver for CPU power on/off.

Change-Id: I526b98d5885855efce019dd09cfd93b8816cbf19
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>

Add support of register notifier.
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I41ef4c63abcc9aee552790b843adb25a5fd0c23e

Add support to get clock's rate value.
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I3ed881053ef323b2ca73e13edd0affda860d381d

Add support of set max latency, to change in the maximum powerup latency
requirements for a specific device currently used by Subsystem.
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I8749886abb1a7884a42c4d156d89c9cd562a5b1a

Add support to call InitFinalize API in Versal which calls
corresponding LibPM API.
Signed-off-by: Ravi Patel <ravi.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I3428b7245b4db1ef6db8a90b7ad20b6e484ed3b2

For the current XilPM calls, The handler of IPI returns information
with 16 Bytes data.
So during QueryData API call for the ClockName and PinFunctionName,
response data(name of clock or function) response[0..3] are used to
return name. And status is not being returned for such API.

Updated XilPM calls reply in a consistent way and The handler of IPI
return information with 32Bytes data. Where response[0] always set
to status.
For the version-2 of QueryData API, during call for the ClockName
and PinFunctionName, response data(name of clock or function) get as
response[1...4].

To support both the version of QueryData API, added version based
compatibility by the use of feature check.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Amit Sunil Dhamne <amit.sunil.dhamne@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I336128bff7bbe659903b0f8ce20ae6da7e3b51b4

In JTAG mode check the ATF handoff structure, if the magic string
is not present then use bl32 and bl33 default values.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I1f2c4a2060d8a2e70d3b5fb2473124b685f257fc

Versal firmware adds extra error codes along with PM error codes
while sending response to driver. This makes incorrect error
identification at driver side.

To fix this, mask the unnecessary error bytes before sending the
error code to the driver.
Signed-off-by: Ravi Patel <ravi.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I18c2f3bd2d067e91344852c2f0c1bafea0e6eb23

GIC registers needs to be stored/restored during system
suspend/resume only and not during CPU idle.
During CPU idle, minimum 1 CPU is in ON state.
Signed-off-by: Ravi Patel <ravi.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I5de2ce3a61bf4260f9385349202b0f592a47aaba

Add below API in feature check list which is actually present in
firmware:
- PM_GET_CHIPID
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Ravi Patel <ravi.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I98b82da74164f065c8835861f74b0f2855e9bcbf

Existing code passes ACPU0 to LibPM as node_id in set_wakeup_source()
call because last suspending core will be ACPU0 in most of the case.

Now it may be possible that user may disable the ACPU0 using hot-plug
and after that it suspends Linux. So in that case ACPU0 will not be
last suspending core.

To overcome above scenario, pass the current running processor ID
while calling set_wakeup_source().
Signed-off-by: Ravi Patel <ravi.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: If15354c2150b5bb1305b5f93ca4e8c7a81d59f0a

Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: Ieb352f0765882efdcb64ef54e6b2a39768590a06

These two targets are build by make subprocesses and are independent.
So splitting them into own targets allow make to build them in parallel.
$(TIMBUILD) script depends on $(TIMDDRTOOL) so specify it in Makefile.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I139fc7fe64d8de275b01a853e15bfb88c4ff840d

Add check when building mrvl_bootimage that size of bl1 image is not bigger
than maximal size.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: Ib873debd3cfdba9acd4c168ee37edab3032e9f25

FORCE target is used as a dependency for other file targets which needs to
be always rebuilt. .PHONY target is standard Makefile target which specify
non-file targets and therefore needs to be always rebuilt.

Targets clean, realclean and distclean are .PHONY targets used to remove
built files. Correctly set that mrvl_clean target is prerequisite for these
clean targets to ensure that built files are removed.

Finally this change with usage of FORCE target allows to remove mrvl_clean
hack from the prerequisites of a8k ${DOIMAGETOOL} target which was used
just to ensure that ${DOIMAGETOOL} is always rebuilt via make subprocess.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I2fa8971244b43f101d846fc433ef7b0b6f139c92

Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: Id766db4a900a56c795fe5ffdd8a2b80b1aaa2132

Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: Iaecd6c24bf334a959ac2bf395c3ee49c810b01a7

Create copy of WTMI images instead of moving them into TF-A build directory.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I2dc24c33b9ce540e4acde51fc1a5c946ae66a5d7

Rather create a temporary copy in $(BUILD_PLAT) and modify only copy.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I256c029106ea6f69faa086fc4e5bee9f68cd257f

$(WTMI_IMG) is used only by $(MAKE) subprocess in $(DOIMAGEPATH) directory.
So calling truncate on $(WTMI_IMG) after $(MAKE) in $(DOIMAGEPATH) has no
effect and can just damage input file for future usage. Therefore remove
this truncate call.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I9925c54c5d3d10eadc19825c5565ad4598a739a7

Save some space by enabling the log messages like bl33 address
only for debug builds. Also check the bl33 and bl32 address and
print only if this is not NULL.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I58d846bf69a75e839eb49abcbb9920af13296886

For boot health status PMU Global General Storage Register 4 is
used. GGS4 can be used for other purpose along with boot health
status. So, change its name from PM_BOOT_HEALTH_STATUS_REG
to PMU_GLOBAL_GEN_STORAGE4.
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I2f5c4c6a161121e7cdb4b9f0f8711d0dad16c372