GitLab

Even though the workaround for CVE-2017-5715 is not a CPU erratum, the
code is piggybacking on the errata framework to print whether the
workaround was applied, missing or not needed.

Change-Id: I821197a4b8560c73fd894cd7cd9ecf9503c72fa3
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Invalidate the Branch Target Buffer (BTB) on entry to EL3 by
temporarily dropping into AArch32 Secure-EL1 and executing the
`BPIALL` instruction.

This is achieved by using 3 vector tables.  There is the runtime
vector table which is used to handle exceptions and 2 additional
tables which are required to implement this workaround.  The
additional tables are `vbar0` and `vbar1`.

The sequence of events for handling a single exception is
as follows:

1) Install vector table `vbar0` which saves the CPU context on entry
   to EL3 and sets up the Secure-EL1 context to execute in AArch32 mode
   with the MMU disabled and I$ enabled.  This is the default vector table.

2) Before doing an ERET into Secure-EL1, switch vbar to point to
   another vector table `vbar1`.  This is required to restore EL3 state
   when returning from the workaround, before proceeding with normal EL3
   exception handling.

3) While in Secure-EL1, the `BPIALL` instruction is executed and an
   SMC call back to EL3 is performed.

4) On entry to EL3 from Secure-EL1, the saved context from step 1) is
   restored.  The vbar is switched to point to `vbar0` in preparation to
   handle further exceptions.  Finally a branch to the runtime vector
   table entry is taken to complete the handling of the original
   exception.

This workaround is enabled by default on the affected CPUs.

NOTE
====

There are 4 different stubs in Secure-EL1.  Each stub corresponds to
an exception type such as Sync/IRQ/FIQ/SError.  Each stub will move a
different value in `R0` before doing an SMC call back into EL3.
Without this piece of information it would not be possible to know
what the original exception type was as we cannot use `ESR_EL3` to
distinguish between IRQs and FIQs.

Change-Id: I90b32d14a3735290b48685d43c70c99daaa4b434
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/



Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

Various CPU drivers in ARM Trusted Firmware register functions to handle
power-down operations. At present, separate functions are registered to
power down individual cores and clusters.

This scheme operates on the basis of core and cluster, and doesn't cater
for extending the hierarchy for power-down operations. For example,
future CPUs might support multiple threads which might need powering
down individually.

This patch therefore reworks the CPU operations framework to allow for
registering power down handlers on specific level basis. Henceforth:

  - Generic code invokes CPU power down operations by the level
    required.

  - CPU drivers explicitly mention CPU_NO_RESET_FUNC when the CPU has no
    reset function.

  - CPU drivers register power down handlers as a list: a mandatory
    handler for level 0, and optional handlers for higher levels.

All existing CPU drivers are adapted to the new CPU operations framework
without needing any functional changes within.

Also update firmware design guide.

Change-Id: I1826842d37a9e60a9e85fdcee7b4b8f6bc1ad043
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

This patch adds cpumerrsr_el1 and l2merrsr_el1 to the register dump on
error for applicable CPUs.

These registers hold the ECC errors on L1 and L2 caches.

This patch updates the A53, A57, A72, A73 (l2merrsr_el1 only) CPU libraries.
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>

This patch adds ARM Cortex-A73 MPCore Processor support
in the CPU specific operations framework. It also includes
this support for the Base FVP port.

Change-Id: I0e26b594f2ec1d28eb815db9810c682e3885716d

In the Cortex-A35/A53/A57 CPUs library code, some of the CPU specific
reset operations are skipped if they have already been applied in a
previous invocation of the reset handler. This precaution is not
required, as all these operations can be reapplied safely.

This patch removes the unneeded test-before-set instructions in
the reset handler for these CPUs.

Change-Id: Ib175952c814dc51f1b5125f76ed6c06a22b95167

This patch adds support for ARM Cortex-A35 processor in the CPU
specific framework, as described in the Cortex-A35 TRM (r0p0).

Change-Id: Ief930a0bdf6cd82f6cb1c3b106f591a71c883464

- Apply a53 errata #826319 to revision <= r0p2
- Apply a53 errata #836870 to revision <= r0p3
- Update docs/cpu-specific-build-macros.md for newly added errata build flags

Change-Id: I44918e36b47dca1fa29695b68700ff9bf888865e
Signed-off-by: Jimmy Huang <jimmy.huang@mediatek.com>

In order for the symbol table in the ELF file to contain the size of
functions written in assembly, it is necessary to report it to the
assembler using the .size directive.

To fulfil the above requirements, this patch introduces an 'endfunc'
macro which contains the .endfunc and .size directives. It also adds
a .func directive to the 'func' assembler macro.

The .func/.endfunc have been used so the assembler can fail if
endfunc is omitted.

Fixes ARM-Software/tf-issues#295

Change-Id: If8cb331b03d7f38fe7e3694d4de26f1075b278fc
Signed-off-by: Kévin Petit <kevin.petit@arm.com>

The CPU specific reset handlers no longer have the freedom
of using any general purpose register because it is being invoked
by the BL3-1 entry point in addition to BL1. The Cortex-A57 CPU
specific reset handler was overwriting x20 register which was being
used by the BL3-1 entry point to save the entry point information.
This patch fixes this bug by reworking the register allocation in the
Cortex-A57 reset handler to avoid using x20. The patch also
explicitly mentions the register clobber list for each of the
callee functions invoked by the reset handler

Change-Id: I28fcff8e742aeed883eaec8f6c4ee2bd3fce30df

This patch adds support to call the reset_handler() function in BL3-1 in the
cold and warm boot paths when another Boot ROM reset_handler() has already run.

This means the BL1 and BL3-1 versions of the CPU and platform specific reset
handlers may execute different code to each other. This enables a developer to
perform additional actions or undo actions already performed during the first
call of the reset handlers e.g. apply additional errata workarounds.

Typically, the reset handler will be first called from the BL1 Boot ROM. Any
additional functionality can be added to the reset handler when it is called
from BL3-1 resident in RW memory. The constant FIRST_RESET_HANDLER_CALL is used
to identify whether this is the first version of the reset handler code to be
executed or an overridden version of the code.

The Cortex-A57 errata workarounds are applied only if they have not already been
applied.

Fixes ARM-software/tf-issue#275

Change-Id: Id295f106e4fda23d6736debdade2ac7f2a9a9053

This patch adds level specific cache maintenance functions
to cache_helpers.S. The new functions 'dcsw_op_levelx',
where '1 <= x <= 3', allow to perform cache maintenance by
set/way for that particular level of cache.  With this patch,
functions to support cache maintenance upto level 3 have
been implemented since it is the highest cache level for
most ARM SoCs.

These functions are now utilized in CPU specific power down
sequences to implement them as mandated by processor specific
technical reference manual.

Change-Id: Icd90ce6b51cff5a12863bcda01b93601417fd45c

This patch adds handlers for dumping Cortex-A57 and Cortex-A53 specific register
state to the CPU specific operations framework. The contents of CPUECTLR_EL1 are
dumped currently.

Change-Id: I63d3dbfc4ac52fef5e25a8cf6b937c6f0975c8ab

This patch adds CPU core and cluster power down sequences to the CPU specific
operations framework introduced in a earlier patch. Cortex-A53, Cortex-A57 and
generic AEM sequences have been added. The latter is suitable for the
Foundation and Base AEM FVPs. A pointer to each CPU's operations structure is
saved in the per-cpu data so that it can be easily accessed during power down
seqeunces.

An optional platform API has been introduced to allow a platform to disable the
Accelerator Coherency Port (ACP) during a cluster power down sequence. The weak
definition of this function (plat_disable_acp()) does not take any action. It
should be overriden with a strong definition if the ACP is present on a
platform.

Change-Id: I8d09bd40d2f528a28d2d3f19b77101178778685d

This patch introduces a framework which will allow CPUs to perform
implementation defined actions after a CPU reset, during a CPU or cluster power
down, and when a crash occurs. CPU specific reset handlers have been implemented
in this patch. Other handlers will be implemented in subsequent patches.

Also moved cpu_helpers.S to the new directory lib/cpus/aarch64/.

Change-Id: I1ca1bade4d101d11a898fb30fea2669f9b37b956

Instead of using the system register helper functions to read
or write system registers, assembler coded functions should
use MRS/MSR instructions. This results in faster and more
compact code.

This change replaces all usage of the helper functions with
direct register accesses.

Change-Id: I791d5f11f257010bb3e6a72c6c5ab8779f1982b3

The current code does not always use data and instruction
barriers as required by the architecture and frequently uses
barriers excessively due to their inclusion in all of the
write_*() helper functions.

Barriers should be used explicitly in assembler or C code
when modifying processor state that requires the barriers in
order to enable review of correctness of the code.

This patch removes the barriers from the helper functions and
introduces them as necessary elsewhere in the code.

PORTING NOTE: check any port of Trusted Firmware for use of
system register helper functions for reliance on the previous
barrier behaviour and add explicit barriers as necessary.

Fixes ARM-software/tf-issues#92

Change-Id: Ie63e187404ff10e0bdcb39292dd9066cb84c53bf

Move almost all system include files to a logical sub-directory
under ./include. The only remaining system include directories
not under ./include are specific to the platform. Move the
corresponding source files to match the include directory
structure.

Also remove pm.h as it is no longer used.

Change-Id: Ie5ea6368ec5fad459f3e8a802ad129135527f0b3

This extends the --gc-sections behaviour to the many assembler
support functions in the firmware images by placing each function
into its own code section. This is achieved by creating a 'func'
macro used to declare each function label.

Fixes ARM-software/tf-issues#80

Change-Id: I301937b630add292d2dec6d2561a7fcfa6fec690

Ctags seem to have a problem with generating tags for assembler symbols
when a comment immediately follows an assembly label.

This patch inserts a single space character between the label
definition and the following comments to help ctags.

The patch is generated by the command:

  git ls-files -- \*.S | xargs sed -i 's/^\([^:]\+\):;/\1: ;/1'

Change-Id: If7a3c9d0f51207ea033cc8b8e1b34acaa0926475

Change-Id: Ic7fb61aabae1d515b9e6baf3dd003807ff42da60

- Add instructions for contributing to ARM Trusted Firmware.

- Update copyright text in all files to acknowledge contributors.

Change-Id: I9311aac81b00c6c167d2f8c889aea403b84450e5

  - Check at link-time that bootloader images will fit in memory
    at run time and that they won't overlap each other.
  - Remove text and rodata orphan sections.
  - Define new linker symbols to remove the need for platform setup
    code to know the order of sections.
  - Reduce the size of the raw binary images by cutting some sections
    out of the disk image and allocating them at load time, whenever
    possible.
  - Rework alignment constraints on sections.
  - Remove unused linker symbols.
  - Homogenize linker symbols names across all BLs.
  - Add some comments in the linker scripts.

Change-Id: I47a328af0ccc7c8ab47fcc0dc6e7dd26160610b9

blx_plat_arch_setup() should only perform platform-specific
architectural setup, e.g. enabling the MMU.  This patch moves
generic architectural setup code out of blx_plat_arch_setup().

Change-Id: I4ccf56b8c4a2fa84909817779a2d97a14aaafab6