GitLab

This patch fixes an issue when secure world timing information
can be leaked because Secure Cycle Counter is not disabled.
For ARMv8.5 the counter gets disabled by setting MDCR_El3.SCCD
bit on CPU cold/warm boot.
For the earlier architectures PMCR_EL0 register is saved/restored
on secure world entry/exit from/to Non-secure state, and cycle
counting gets disabled by setting PMCR_EL0.DP bit.
'include\aarch64\arch.h' header file was tided up and new
ARMv8.5-PMU related definitions were added.

Change-Id: I6f56db6bc77504634a352388990ad925a69ebbfa
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

This patch introduces an additional precautionary step to further
enhance protection against variant 4. During the context initialisation
before we enter the various BL stages, the SPSR.SSBS bit is explicitly
set to zero. As such, speculative loads/stores are by default disabled
for all BL stages when they start executing. Subsequently, each BL
stage, can choose to enable speculative loads/stores or keep them
disabled.

This change doesn't affect the initial execution context of BL33 which
is totally platform dependent and, thus, it is intentionally left up to
each platform to initialise.

For Arm platforms, SPSR.SSBS is set to zero for BL33 too. This means
that, for Arm platforms, all BL stages start with speculative
loads/stores disabled.

Change-Id: Ie47d39c391d3f20fc2852fc59dbd336f8cacdd6c
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

This patch enables MTE for Normal world if the CPU suppors it. Enabling
MTE for secure world will be done later.

Change-Id: I9ef64460beaba15e9a9c20ab02da4fb2208b6f7d
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch removes incorrect SCTLR_V_BIT definition and adds
definitions for ARMv8.3-Pauth EnIB, EnDA and EnDB bits.

Change-Id: I1384c0a01f56f3d945833464a827036252c75c2e
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

Those defines are used in STM32MP1 clock driver.
It is better to put them altogether with already defined registers.

Change-Id: I6f8ad8c2477b947af6f76283a4ef5c40212d0027
Signed-off-by: Yann Gautier <yann.gautier@st.com>

This patch adds the functionality needed for platforms to provide
Branch Target Identification (BTI) extension, introduced to AArch64
in Armv8.5-A by adding BTI instruction used to mark valid targets
for indirect branches. The patch sets new GP bit [50] to the stage 1
Translation Table Block and Page entries to denote guarded EL3 code
pages which will cause processor to trap instructions in protected
pages trying to perform an indirect branch to any instruction other
than BTI.
BTI feature is selected by BRANCH_PROTECTION option which supersedes
the previous ENABLE_PAUTH used for Armv8.3-A Pointer Authentication
and is disabled by default. Enabling BTI requires compiler support
and was tested with GCC versions 9.0.0, 9.0.1 and 10.0.0.
The assembly macros and helpers are modified to accommodate the BTI
instruction.
This is an experimental feature.
Note. The previous ENABLE_PAUTH build option to enable PAuth in EL3
is now made as an internal flag and BRANCH_PROTECTION flag should be
used instead to enable Pointer Authentication.
Note. USE_LIBROM=1 option is currently not supported.

Change-Id: Ifaf4438609b16647dc79468b70cd1f47a623362e
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

This gives each Secure Partition complete freedom on its address space.
Previously, the memory used by the exception vectors was reserved and
couldn't be used. Also, it always had to be mapped, forcing SPM to
generate translation tables that included the exception vectors as well
as the Partition memory regions. With this change, partitions can reduce
their address space size easily.

Change-Id: I67fb5e9bdf2870b73347f23bff702fab0a8f8711
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch applies the new MSR instruction to directly set the
PSTATE.SSBS bit which controls speculative loads. This new instruction
is available at Neoverse N1 core so it's utilised.

Change-Id: Iee18a8b042c90fdb72d2b98f364dcfbb17510728
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

Complete the MPAM enablement in TF-A for lower ELs by enabling the EL2
traps in MPAMHCR_EL2 and MPAM2_EL2.This prevents an
MPAM-unaware-hypervisor to be restricted by an MPAM-aware-guest.

Change-Id: I47bf3f833fa22baa590f83d49cc0e3f2974e698d
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

The workarounds for these errata are so closely related that it is
better to only have one patch to make it easier to understand.

Change-Id: I0287fa69aefa8b72f884833f6ed0e7775ca834e9
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>

ARMv8.3-PAuth adds functionality that supports address authentication of
the contents of a register before that register is used as the target of
an indirect branch, or as a load.

This feature is supported only in AArch64 state.

This feature is mandatory in ARMv8.3 implementations.

This feature adds several registers to EL1. A new option called
CTX_INCLUDE_PAUTH_REGS has been added to select if the TF needs to save
them during Non-secure <-> Secure world switches. This option must be
enabled if the hardware has the registers or the values will be leaked
during world switches.

To prevent leaks, this patch also disables pointer authentication in the
Secure world if CTX_INCLUDE_PAUTH_REGS is 0. Any attempt to use it will
be trapped in EL3.

Change-Id: I27beba9907b9a86c6df1d0c5bf6180c972830855
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Implicit Error Synchronization Barrier (IESB) might not be correctly
generated in Cortex-A75 r0p0. To prevent this, IESB are enabled at all
expection levels.

Change-Id: I2a1a568668a31e4f3f38d0fba1d632ad9939e5ad
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

In a system with ARMv8.5-PMU implemented:

- If EL3 is using AArch32, setting MDCR_EL3.SCCD to 1 disables counting
  in Secure state in PMCCNTR.

- If EL3 is using AArch64, setting SDCR.SCCD to 1 disables counting in
  Secure state in PMCCNTR_EL0.

So far this effect has been achieved by setting PMCR_EL0.DP (in AArch64)
or PMCR.DP (in AArch32) to 1 instead, but this isn't considered secure
as any EL can change that value.

Change-Id: I82cbb3e48f2e5a55c44d9c4445683c5881ef1f6f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

ARMv8.4-TTST (Small Translation tables) relaxes the lower limit on the
size of translation tables by increasing the maximum permitted value
of the T1SZ and T0SZ fields in TCR_EL1, TCR_EL2, TCR_EL3, VTCR_EL2 and
VSTCR_EL2.

This feature is supported in AArch64 state only.

This patch adds support for this feature to both versions of the
translation tables library. It also removes the static build time
checks for virtual address space size checks to runtime assertions.

Change-Id: I4e8cebc197ec1c2092dc7d307486616786e6c093
Signed-off-by: Sathees Balya <sathees.balya@arm.com>

ARMv8.2-TTCNP is mandatory from ARMv8.2 onwards, but it can be implemented
in CPUs that don't implement all mandatory 8.2 features (and so have to
claim to be a lower version).

This patch removes usage of the ARM_ARCH_AT_LEAST() macro and uses system
ID registers to detect whether it is needed to set the bit or not.

Change-Id: I7bcbf0c7c937590dfc2ca668cfd9267c50f7d52c
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}

The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).

For example, this patch had to be created because two headers were
called the same way: e0ea0928 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3 ("drivers: add tzc380 support").

This problem was introduced in commit 4ecca339

 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.

Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.

Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The architecture dependant header files in include/lib/${ARCH} and
include/common/${ARCH} have been moved to /include/arch/${ARCH}.

Change-Id: I96f30fdb80b191a51448ddf11b1d4a0624c03394
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch enables the Data Independent Timing
functionality (DIT) in EL3 if supported
by the platform.

Change-Id: Ia527d6aa2ee88a9a9fe1c941220404b9ff5567e5
Signed-off-by: Sathees Balya <sathees.balya@arm.com>

Some of the affected macros can only be used from C code. In general, we
use arch_helpers.h for any C helpers to access registers. For
consistency, the other macros have been moved as well.

Also, import some AArch32 helpers from TF-A-Tests.

Change-Id: Ie8fe1ddeadba5336c12971ddc39a7883121386b1
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The Armv8.5 extensions introduces PSTATE.SSBS (Speculation Store Bypass
Safe) bit to mitigate against Variant 4 vulnerabilities. Although an
Armv8.5 feature, this can be implemented by CPUs implementing earlier
version of the architecture.

With this patch, when both PSTATE.SSBS is implemented and
DYNAMIC_WORKAROUND_CVE_2018_3639 is active, querying for
SMCCC_ARCH_WORKAROUND_2 via. SMCCC_ARCH_FEATURES call would return 1 to
indicate that mitigation on the PE is either permanently enabled or not
required.

When SSBS is implemented, SCTLR_EL3.DSSBS is initialized to 0 at reset
of every BL stage. This means that EL3 always executes with mitigation
applied.

For Cortex A76, if the PE implements SSBS, the existing mitigation (by
using a different vector table, and tweaking CPU ACTLR2) is not used.

Change-Id: Ib0386c5714184144d4747951751c2fc6ba4242b6
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The headers forked at some point in the past and have diverged a lot. In
order to make it easier to share code between TF-A-Tests and TF-A, this
patch synchronises most of the definitions in the mentioned headers.

This is not a complete sync, it has to be followed by more cleanup.

This patch also removes the read helpers for the AArch32 instructions
ats1cpr and ats1hr (they are write-only).

Change-Id: Id13ecd7aeb83bd2318cd47156d71a42f1c9f6ba2
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Pointer authentication is an Armv8.3 feature that introduces
instructions that can be used to authenticate and verify pointers.

Pointer authentication instructions are allowed to be accessed from all
ELs but only when EL3 explicitly allows for it; otherwise, their usage
will trap to EL3. Since EL3 doesn't have trap handling in place, this
patch unconditionally disables all related traps to EL3 to avoid
potential misconfiguration leading to an unhandled EL3 exception.

Fixes ARM-software/tf-issues#629

Change-Id: I9bd2efe0dc714196f503713b721ffbf05672c14d
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Change-Id: Icd1cdd42afdc78895a9be6c46b414b0a155cfa63
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

fixes arm-software/tf-issues#620
Signed-off-by: Jan Dabros <jsd@semihalf.com>

Memory Partitioning And Monitoring is an Armv8.4 feature that enables
various memory system components and resources to define partitions.
Software running at various ELs can then assign themselves to the
desired partition to control their performance aspects.

With this patch, when ENABLE_MPAM_FOR_LOWER_ELS is set to 1, EL3 allows
lower ELs to access their own MPAM registers without trapping to EL3.
This patch however doesn't make use of partitioning in EL3; platform
initialisation code should configure and use partitions in EL3 if
required.

Change-Id: I5a55b6771ccaa0c1cffc05543d2116b60cbbcdcd
Co-authored-by: James Morse <james.morse@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The translation library is useful elsewhere. Even though this repository
doesn't exercise the EL2 support of the library, it is better to have it
here as well to make it easier to maintain.

enable_mmu_secure() and enable_mmu_direct() have been deprecated. The
functions are still present, but they are behind ERROR_DEPRECATED and
they call the new functions enable_mmu_svc_mon() and
enable_mmu_direct_svc_mon().

Change-Id: I13ad10cd048d9cc2d55e0fff9a5133671b67dcba
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Also change header guards to fix defects of MISRA C-2012 Rule 21.1.

Change-Id: Ied0d4b0e557ef6119ab669d106d2ac5d99620c57
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Define the values as unsigned int or unsigned long long based on the
actual size of the register. This prevents subtle issues caused by
having a type that is too small. For example:

    #define OPTION_ENABLE 0x3
    #define OPTION_SHIFT  32

    uint64_t mask = OPTION_ENABLE << OPTION_SHIFT;

Because OPTION_ENABLE fits in an int, the value is considered an int.
This means that, after shifting it 32 places to the left, the final
result is 0. The correct way to define the values is:

    #define OPTION_ENABLE ULL(0x3)
    #define OPTION_SHIFT  U(32)

In this case, the compiler is forced to use a 64 bit value from the
start, so shifting it 32 places to the left results in the expected
value.

Change-Id: Ieaf2ffc2d8caa48c622db011f2aef549e713e019
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: Ifea46da46d1bfd01b341acfad75df5bcab48a204
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Currently TF-A doesn't initialise CNTFRQ register in CNTCTLBase
frame of the system timer. ARM ARM states that "The instance of
the register in the CNTCTLBase frame must be programmed with this
value as part of system initialization."

The psci_arch_setup() updates the CNTFRQ system register but
according to the ARM ARM, this instance of the register is
independent of the memory mapped instance. This is only an issue
for Normal world software which relies on the memory mapped
instance rather than the system register one.

This patch resolves the issue for ARM platforms.

The patch also solves a related issue on Juno, wherein
CNTBaseN.CNTFRQ can be written and does not reflect the value of
the register in CNTCTLBase frame. Hence this patch additionally
updates CNTFRQ register in the Non Secure frame of the CNTBaseN.

Fixes ARM-Software/tf-issues#593

Change-Id: I09cebb6633688b34d5b1bc349fbde4751025b350
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

The ARMv8.4 RAS extensions introduce architectural support for software
to inject faults into the system in order to test fault-handling
software. This patch introduces the build option FAULT_HANDLING_SUPPORT
to allow for lower ELs to use registers in the Standard Error Record to
inject fault. The build option RAS_EXTENSIONS must also be enabled along
with fault injection.

This feature is intended for testing purposes only, and is advisable to
keep disabled for production images.

Change-Id: I6f7a4454b15aec098f9505a10eb188c2f928f7ea
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The ARMv8 RAS Extensions introduced Standard Error Records which are a
set of standard registers through which:

  - Platform can configure RAS node policy; e.g., notification
    mechanism;

  - RAS nodes can record and expose error information for error handling
    agents.

Standard Error Records can either be accessed via. memory-mapped
or System registers. This patch adds helper functions to access
registers and fields within an error record.

Change-Id: I6594ba799f4a1789d7b1e45b3e17fd40e7e0ba5c
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

RAS extensions are mandatory for ARMv8.2 CPUs, but are also optional
extensions to base ARMv8.0 architecture.

This patch adds build system support to enable RAS features in ARM
Trusted Firmware. A boolean build option RAS_EXTENSION is introduced for
this.

With RAS_EXTENSION, an Exception Synchronization Barrier (ESB) is
inserted at all EL3 vector entry and exit. ESBs will synchronize pending
external aborts before entering EL3, and therefore will contain and
attribute errors to lower EL execution. Any errors thus synchronized are
detected via. DISR_EL1 register.

When RAS_EXTENSION is set to 1, HANDLE_EL3_EA_FIRST must also be set to 1.

Change-Id: I38a19d84014d4d8af688bd81d61ba582c039383a
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

At present, any External Abort routed to EL3 is reported as an unhandled
exception and cause a panic. This patch enables ARM Trusted Firmware to
handle External Aborts routed to EL3.

With this patch, when an External Abort is received at EL3, its handling
is delegated to plat_ea_handler() function. Platforms can provide their
own implementation of this function. This patch adds a weak definition
of the said function that prints out a message and just panics.

In order to support handling External Aborts at EL3, the build option
HANDLE_EA_EL3_FIRST must be set to 1.

Before this patch, HANDLE_EA_EL3_FIRST wasn't passed down to
compilation; this patch fixes that too.

Change-Id: I4d07b7e65eb191ff72d63b909ae9512478cd01a1
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Change-Id: I989c1f4aef8e3cb20d5d19e6347575e6449bb60b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Add some AMU helper functions to allow configuring, reading and
writing of the Group 0 and Group 1 counters.  Documentation for these
helpers will come in a separate patch.

Change-Id: I656e070d2dae830c22414f694aa655341d4e2c40
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

If the CSV2 field reads as 1 then branch targets trained in one
context cannot affect speculative execution in a different context.
In that case skip the workaround on Cortex A75.

Change-Id: I4d5504cba516a67311fb5f0657b08f72909cbd38
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Invalidate the Branch Target Buffer (BTB) on entry to EL3 by
temporarily dropping into AArch32 Secure-EL1 and executing the
`BPIALL` instruction.

This is achieved by using 3 vector tables.  There is the runtime
vector table which is used to handle exceptions and 2 additional
tables which are required to implement this workaround.  The
additional tables are `vbar0` and `vbar1`.

The sequence of events for handling a single exception is
as follows:

1) Install vector table `vbar0` which saves the CPU context on entry
   to EL3 and sets up the Secure-EL1 context to execute in AArch32 mode
   with the MMU disabled and I$ enabled.  This is the default vector table.

2) Before doing an ERET into Secure-EL1, switch vbar to point to
   another vector table `vbar1`.  This is required to restore EL3 state
   when returning from the workaround, before proceeding with normal EL3
   exception handling.

3) While in Secure-EL1, the `BPIALL` instruction is executed and an
   SMC call back to EL3 is performed.

4) On entry to EL3 from Secure-EL1, the saved context from step 1) is
   restored.  The vbar is switched to point to `vbar0` in preparation to
   handle further exceptions.  Finally a branch to the runtime vector
   table entry is taken to complete the handling of the original
   exception.

This workaround is enabled by default on the affected CPUs.

NOTE
====

There are 4 different stubs in Secure-EL1.  Each stub corresponds to
an exception type such as Sync/IRQ/FIQ/SError.  Each stub will move a
different value in `R0` before doing an SMC call back into EL3.
Without this piece of information it would not be possible to know
what the original exception type was as we cannot use `ESR_EL3` to
distinguish between IRQs and FIQs.

Change-Id: I90b32d14a3735290b48685d43c70c99daaa4b434
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

This patch adds a new build option, ENABLE_SVE_FOR_NS, which when set
to one EL3 will check to see if the Scalable Vector Extension (SVE) is
implemented when entering and exiting the Non-secure world.

If SVE is implemented, EL3 will do the following:

- Entry to Non-secure world: SIMD, FP and SVE functionality is enabled.

- Exit from Non-secure world: SIMD, FP and SVE functionality is
  disabled. As SIMD and FP registers are part of the SVE Z-registers
  then any use of SIMD / FP functionality would corrupt the SVE
  registers.

The build option default is 1. The SVE functionality is only supported
on AArch64 and so the build option is set to zero when the target
archiecture is AArch32.

This build option is not compatible with the CTX_INCLUDE_FPREGS - an
assert will be raised on platforms where SVE is implemented and both
ENABLE_SVE_FOR_NS and CTX_INCLUDE_FPREGS are set to 1.

Also note this change prevents secure world use of FP&SIMD registers on
SVE-enabled platforms. Existing Secure-EL1 Payloads will not work on
such platforms unless ENABLE_SVE_FOR_NS is set to 0.

Additionally, on the first entry into the Non-secure world the SVE
functionality is enabled and the SVE Z-register length is set to the
maximum size allowed by the architecture. This includes the use case
where EL2 is implemented but not used.

Change-Id: Ie2d733ddaba0b9bef1d7c9765503155188fe7dae
Signed-off-by: David Cunado <david.cunado@arm.com>

The `ENABLE_AMU` build option can be used to enable the
architecturally defined AMU counters.  At present, there is no support
for the auxiliary counter group.

Change-Id: I7ea0c0a00327f463199d1b0a481f01dadb09d312
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>