GitLab

This patch provides the following features and makes modifications
listed below:
- Individual APIAKey key generation for each CPU.
- New key generation on every BL31 warm boot and TSP CPU On event.
- Per-CPU storage of APIAKey added in percpu_data[]
  of cpu_data structure.
- `plat_init_apiakey()` function replaced with `plat_init_apkey()`
  which returns 128-bit value and uses Generic timer physical counter
  value to increase the randomness of the generated key.
  The new function can be used for generation of all ARMv8.3-PAuth keys
- ARMv8.3-PAuth specific code placed in `lib\extensions\pauth`.
- New `pauth_init_enable_el1()` and `pauth_init_enable_el3()` functions
  generate, program and enable APIAKey_EL1 for EL1 and EL3 respectively;
  pauth_disable_el1()` and `pauth_disable_el3()` functions disable
  PAuth for EL1 and EL3 respectively;
  `pauth_load_bl31_apiakey()` loads saved per-CPU APIAKey_EL1 from
  cpu-data structure.
- Combined `save_gp_pauth_registers()` function replaces calls to
  `save_gp_registers()` and `pauth_context_save()`;
  `restore_gp_pauth_registers()` replaces `pauth_context_restore()`
  and `restore_gp_registers()` calls.
- `restore_gp_registers_eret()` function removed with corresponding
  code placed in `el3_exit()`.
- Fixed the issue when `pauth_t pauth_ctx` structure allocated space
  for 12 uint64_t PAuth registers instead of 10 by removal of macro
  CTX_PACGAKEY_END from `include/lib/el3_runtime/aarch64/context.h`
  and assigning its value to CTX_PAUTH_REGS_END.
- Use of MODE_SP_ELX and MODE_SP_EL0 macro definitions
  in `msr	spsel`  instruction instead of hard-coded values.
- Changes in documentation related to ARMv8.3-PAuth and ARMv8.5-BTI.

Change-Id: Id18b81cc46f52a783a7e6a09b9f149b6ce803211
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

This patch adds the functionality needed for platforms to provide
Branch Target Identification (BTI) extension, introduced to AArch64
in Armv8.5-A by adding BTI instruction used to mark valid targets
for indirect branches. The patch sets new GP bit [50] to the stage 1
Translation Table Block and Page entries to denote guarded EL3 code
pages which will cause processor to trap instructions in protected
pages trying to perform an indirect branch to any instruction other
than BTI.
BTI feature is selected by BRANCH_PROTECTION option which supersedes
the previous ENABLE_PAUTH used for Armv8.3-A Pointer Authentication
and is disabled by default. Enabling BTI requires compiler support
and was tested with GCC versions 9.0.0, 9.0.1 and 10.0.0.
The assembly macros and helpers are modified to accommodate the BTI
instruction.
This is an experimental feature.
Note. The previous ENABLE_PAUTH build option to enable PAuth in EL3
is now made as an internal flag and BRANCH_PROTECTION flag should be
used instead to enable Pointer Authentication.
Note. USE_LIBROM=1 option is currently not supported.

Change-Id: Ifaf4438609b16647dc79468b70cd1f47a623362e
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

The relocation fixup code must be called at the beginning of bl31
entrypoint to ensure that CPU specific reset handlers are fixed up for
relocations.

Change-Id: Icb04eacb2d4c26c26b08b768d871d2c82777babb
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

In the current Pointer Authentication support added in
commit b86048c4


PAuth gets enabled in BL31 cold boot entrypoint only,
(see bl31_entrypoint() in bl31\aarch64\bl31_entrypoint.S)
but not in bl31_warm_entrypoint().
This results in EnIA bit [31] in SCTLR_EL3 not being set
and pointer authentication disabled after CPU wake-up event.

Fixes ARM-software/tf-issues#684

Change-Id: I27a67804764dfba2a6d72ca119ca2bcff4f536d6
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

The size increase after enabling options related to ARMv8.3-PAuth is:

+----------------------------+-------+-------+-------+--------+
|                            |  text |  bss  |  data | rodata |
+----------------------------+-------+-------+-------+--------+
| CTX_INCLUDE_PAUTH_REGS = 1 |  +192 | +1536 |   +0  |   +0   |
|                            |  0.3% |  3.1% |       |        |
+----------------------------+-------+-------+-------+--------+
| ENABLE_PAUTH = 1           | +1848 | +1536 |  +16  |   +0   |
|                            |  3.3% |  3.1% |  3.1% |        |
+----------------------------+-------+-------+-------+--------+

Results calculated with the following build configuration:

    make PLAT=fvp SPD=tspd DEBUG=1 \
    SDEI_SUPPORT=1                 \
    EL3_EXCEPTION_HANDLING=1       \
    TSP_NS_INTR_ASYNC_PREEMPT=1    \
    CTX_INCLUDE_PAUTH_REGS=1       \
    ENABLE_PAUTH=1

Change-Id: I43db7e509a4f39da6599ec2faa690d197573ec1b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}

The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).

For example, this patch had to be created because two headers were
called the same way: e0ea0928 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3 ("drivers: add tzc380 support").

This problem was introduced in commit 4ecca339

 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.

Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.

Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch introduces Position Independant Executable(PIE) support
in TF-A. As a initial prototype, only BL31 can support PIE. A trivial
dynamic linker is implemented which supports fixing up Global Offset
Table(GOT) and Dynamic relocations(.rela.dyn). The fixup_gdt_reloc()
helper function implements this linker and this needs to be called
early in the boot sequence prior to invoking C functions. The GOT is
placed in the RO section of BL31 binary for improved security and the
BL31 linker script is modified to export the appropriate symbols
required for the dynamic linker.

The C compiler always generates PC relative addresses to linker symbols
and hence referencing symbols exporting constants are a problem when
relocating the binary. Hence the reference to the
`__PERCPU_TIMESTAMP_SIZE__` symbol in PMF is removed and is now calculated
at runtime based on start and end addresses.

Change-Id: I1228583ff92cf432963b7cef052e95d995cca93d
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

No functional changes.

Change-Id: I9638e02acb9b22eb794ebf45aad84348a710287e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Having an active stack while enabling MMU has shown coherency problems.
This patch builds on top of translation library changes that introduces
MMU-enabling without using stacks.

Previously, with HW_ASSISTED_COHERENCY, data caches were disabled while
enabling MMU only because of active stack. Now that we can enable MMU
without using stack, we can enable both MMU and data caches at the same
time.

NOTE: Since this feature depends on using translation table library v2,
disallow using translation table library v1 with HW_ASSISTED_COHERENCY.

Fixes ARM-software/tf-issues#566

Change-Id: Ie55aba0c23ee9c5109eb3454cb8fa45d74f8bbb2
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

When the MMU is enabled and the translation tables are mapped, data
read/writes to the translation tables are made using the attributes
specified in the translation tables themselves. However, the MMU
performs table walks with the attributes specified in TCR_ELx. They are
completely independent, so special care has to be taken to make sure
that they are the same.

This has to be done manually because it is not practical to have a test
in the code. Such a test would need to know the virtual memory region
that contains the translation tables and check that for all of the
tables the attributes match the ones in TCR_ELx. As the tables may not
even be mapped at all, this isn't a test that can be made generic.

The flags used by enable_mmu_xxx() have been moved to the same header
where the functions are.

Also, some comments in the linker scripts related to the translation
tables have been fixed.

Change-Id: I1754768bffdae75f53561b1c4a5baf043b45a304
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch introduces a new BL handover interface. It essentially allows
passing 4 arguments between the different BL stages. Effort has been made
so as to be compatible with the previous handover interface. The previous
blx_early_platform_setup() platform API is now deprecated and the new
blx_early_platform_setup2() variant is introduced. The weak compatiblity
implementation for the new API is done in the `plat_bl_common.c` file.
Some of the new arguments in the new API will be reserved for generic
code use when dynamic configuration support is implemented. Otherwise
the other registers are available for platform use.

Change-Id: Ifddfe2ea8e32497fe1beb565cac155ad9d50d404
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch updates the el3_arch_init_common macro so that it fully
initialises essential control registers rather then relying on hardware
to set the reset values.

The context management functions are also updated to fully initialise
the appropriate control registers when initialising the non-secure and
secure context structures and when preparing to leave EL3 for a lower
EL.

This gives better alignement with the ARM ARM which states that software
must initialise RES0 and RES1 fields with 0 / 1.

This patch also corrects the following typos:

"NASCR definitions" -> "NSACR definitions"

Change-Id: Ia8940b8351dc27bc09e2138b011e249655041cfc
Signed-off-by: David Cunado <david.cunado@arm.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/



Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

This patch introduces a build option to enable D-cache early on the CPU
after warm boot. This is applicable for platforms which do not require
interconnect programming to enable cache coherency (eg: single cluster
platforms). If this option is enabled, then warm boot path enables
D-caches immediately after enabling MMU.

Fixes ARM-Software/tf-issues#456

Change-Id: I44c8787d116d7217837ced3bcf0b1d3441c8d80e
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

The files affected by this patch don't really depend on `xlat_tables.h`.
By changing the included file it becomes easier to switch between the
two versions of the translation tables library.

Change-Id: Idae9171c490e0865cb55883b19eaf942457c4ccc
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

At present, warm-booted CPUs keep their caches disabled when enabling
MMU, and remains so until they enter coherency later.

On systems with hardware-assisted coherency, for which
HW_ASSISTED_COHERENCY build flag would be enabled, warm-booted CPUs can
have both caches and MMU enabled at once.

Change-Id: Icb0adb026e01aecf34beadf49c88faa9dd368327
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

In order to quantify the overall time spent in the PSCI software
implementation, an initial collection of PMF instrumentation points
has been added.

Instrumentation has been added to the following code paths:

- Entry to PSCI SMC handler.  The timestamp is captured as early
  as possible during the runtime exception and stored in memory
  before entering the PSCI SMC handler.

- Exit from PSCI SMC handler.  The timestamp is captured after
  normal return from the PSCI SMC handler or if a low power state
  was requested it is captured in the bl31 warm boot path before
  return to normal world.

- Entry to low power state.  The timestamp is captured before entry
  to a low power state which implies either standby or power down.
  As these power states are mutually exclusive, only one timestamp
  is defined to describe both.  It is possible to differentiate between
  the two power states using the PSCI STAT interface.

- Exit from low power state.  The timestamp is captured after a standby
  or power up operation has completed.

To calculate the number of cycles spent running code in Trusted Firmware
one can perform the following calculation:

(exit_psci - enter_psci) - (exit_low_pwr - enter_low_pwr).

The resulting number of cycles can be converted to time given the
frequency of the counter.

Change-Id: Ie3b8f3d16409b6703747093b3a2d5c7429ad0166
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

This patch introduces the PSCI Library interface. The major changes
introduced are as follows:

* Earlier BL31 was responsible for Architectural initialization during cold
boot via bl31_arch_setup() whereas PSCI was responsible for the same during
warm boot. This functionality is now consolidated by the PSCI library
and it does Architectural initialization via psci_arch_setup() during both
cold and warm boots.

* Earlier the warm boot entry point was always `psci_entrypoint()`. This was
not flexible enough as a library interface. Now PSCI expects the runtime
firmware to provide the entry point via `psci_setup()`. A new function
`bl31_warm_entrypoint` is introduced in BL31 and the previous
`psci_entrypoint()` is deprecated.

* The `smc_helpers.h` is reorganized to separate the SMC Calling Convention
defines from the Trusted Firmware SMC helpers. The former is now in a new
header file `smcc.h` and the SMC helpers are moved to Architecture specific
header.

* The CPU context is used by PSCI for context initialization and
restoration after power down (PSCI Context). It is also used by BL31 for SMC
handling and context management during Normal-Secure world switch (SMC
Context). The `psci_smc_handler()` interface is redefined to not use SMC
helper macros thus enabling to decouple the PSCI context from EL3 runtime
firmware SMC context. This enables PSCI to be integrated with other runtime
firmware using a different SMC context.

NOTE: With this patch the architectural setup done in `bl31_arch_setup()`
is done as part of `psci_setup()` and hence `bl31_platform_setup()` will be
invoked prior to architectural setup. It is highly unlikely that the platform
setup will depend on architectural setup and cause any failure. Please be
be aware of this change in sequence.

Change-Id: I7f497a08d33be234bbb822c28146250cb20dab73

This patch removes the dash character from the image name, to
follow the image terminology in the Trusted Firmware Wiki page:

    https://github.com/ARM-software/arm-trusted-firmware/wiki

Changes apply to output messages, comments and documentation.

non-ARM platform files have been left unmodified.

Change-Id: Ic2a99be4ed929d52afbeb27ac765ceffce46ed76

This patch introduces a new build option named COLD_BOOT_SINGLE_CPU,
which allows platforms that only release a single CPU out of reset to
slightly optimise their cold boot code, both in terms of code size
and performance.

COLD_BOOT_SINGLE_CPU defaults to 0, which assumes that the platform
may release several CPUs out of reset. In this case, the cold reset
code needs to coordinate all CPUs via the usual primary/secondary
CPU distinction.

If a platform guarantees that only a single CPU will ever be released
out of reset, there is no need to arbitrate execution ; the notion of
primary and secondary CPUs itself no longer exists. Such platforms
may set COLD_BOOT_SINGLE_CPU to 1 in order to compile out the
primary/secondary CPU identification in the cold reset code.

All ARM standard platforms can release several CPUs out of reset
so they use COLD_BOOT_SINGLE_CPU=0. However, on CSS platforms like
Juno, bringing up more than one CPU at reset should only be attempted
when booting an EL3 payload, as it is not fully supported in the
normal boot flow.

For platforms using COLD_BOOT_SINGLE_CPU=1, the following 2 platform
APIs become optional:
  - plat_secondary_cold_boot_setup();
  - plat_is_my_cpu_primary().
The Porting Guide has been updated to reflect that.

User Guide updated as well.

Change-Id: Ic5b474e61b7aec1377d1e0b6925d17dfc376c46b

On the ARMv8 architecture, cache maintenance operations by set/way on the last
level of integrated cache do not affect the system cache. This means that such a
flush or clean operation could result in the data being pushed out to the system
cache rather than main memory. Another CPU could access this data before it
enables its data cache or MMU. Such accesses could be serviced from the main
memory instead of the system cache. If the data in the sysem cache has not yet
been flushed or evicted to main memory then there could be a loss of
coherency. The only mechanism to guarantee that the main memory will be updated
is to use cache maintenance operations to the PoC by MVA(See section D3.4.11
(System level caches) of ARMv8-A Reference Manual (Issue A.g/ARM DDI0487A.G).

This patch removes the reliance of Trusted Firmware on the flush by set/way
operation to ensure visibility of data in the main memory. Cache maintenance
operations by MVA are now used instead. The following are the broad category of
changes:

1. The RW areas of BL2/BL31/BL32 are invalidated by MVA before the C runtime is
   initialised. This ensures that any stale cache lines at any level of cache
   are removed.

2. Updates to global data in runtime firmware (BL31) by the primary CPU are made
   visible to secondary CPUs using a cache clean operation by MVA.

3. Cache maintenance by set/way operations are only used prior to power down.

NOTE: NON-UPSTREAM TRUSTED FIRMWARE CODE SHOULD MAKE EQUIVALENT CHANGES IN
ORDER TO FUNCTION CORRECTLY ON PLATFORMS WITH SUPPORT FOR SYSTEM CACHES.

Fixes ARM-software/tf-issues#205

Change-Id: I64f1b398de0432813a0e0881d70f8337681f6e9a

This patch introduces a new platform build option, called
PROGRAMMABLE_RESET_ADDRESS, which tells whether the platform has
a programmable or fixed reset vector address.

If the reset vector address is fixed then the code relies on the
platform_get_entrypoint() mailbox mechanism to figure out where
it is supposed to jump. On the other hand, if it is programmable
then it is assumed that the platform code will program directly
the right address into the RVBAR register (instead of using the
mailbox redirection) so the mailbox is ignored in this case.

Change-Id: If59c3b11fb1f692976e1d8b96c7e2da0ebfba308

The attempt to run the CPU reset code as soon as possible after reset
results in highly complex conditional code relating to the
RESET_TO_BL31 option.

This patch relaxes this requirement a little. In the BL1, BL3-1 and
PSCI entrypoints code, the sequence of operations is now as follows:
 1) Detect whether it is a cold or warm boot;
 2) For cold boot, detect whether it is the primary or a secondary
    CPU. This is needed to handle multiple CPUs entering cold reset
    simultaneously;
 3) Run the CPU init code.

This patch also abstracts the EL3 registers initialisation done by
the BL1, BL3-1 and PSCI entrypoints into common code.

This improves code re-use and consolidates the code flows for
different types of systems.

NOTE: THE FUNCTION plat_secondary_cold_boot() IS NOW EXPECTED TO
NEVER RETURN. THIS PATCH FORCES PLATFORM PORTS THAT RELIED ON THE
FORMER RETRY LOOP AT THE CALL SITE TO MODIFY THEIR IMPLEMENTATION.
OTHERWISE, SECONDARY CPUS WILL PANIC.

Change-Id: If5ecd74d75bee700b1bd718d23d7556b8f863546

In order for the symbol table in the ELF file to contain the size of
functions written in assembly, it is necessary to report it to the
assembler using the .size directive.

To fulfil the above requirements, this patch introduces an 'endfunc'
macro which contains the .endfunc and .size directives. It also adds
a .func directive to the 'func' assembler macro.

The .func/.endfunc have been used so the assembler can fail if
endfunc is omitted.

Fixes ARM-Software/tf-issues#295

Change-Id: If8cb331b03d7f38fe7e3694d4de26f1075b278fc
Signed-off-by: Kévin Petit <kevin.petit@arm.com>

The cpu-ops pointer was initialized before enabling the data cache in the cold
and warm boot paths. This required a DCIVAC cache maintenance operation to
invalidate any stale cache lines resident in other cpus.

This patch moves this initialization to the bl31_arch_setup() function
which is always called after the data cache and MMU has been enabled.

This change removes the need:
 1. for the DCIVAC cache maintenance operation.
 2. to initialise the CPU ops upon resumption from a PSCI CPU_SUSPEND
    call since memory contents are always preserved in this case.

Change-Id: Ibb2fa2f7460d1a1f1e721242025e382734c204c6

This patch adds support to call the reset_handler() function in BL3-1 in the
cold and warm boot paths when another Boot ROM reset_handler() has already run.

This means the BL1 and BL3-1 versions of the CPU and platform specific reset
handlers may execute different code to each other. This enables a developer to
perform additional actions or undo actions already performed during the first
call of the reset handlers e.g. apply additional errata workarounds.

Typically, the reset handler will be first called from the BL1 Boot ROM. Any
additional functionality can be added to the reset handler when it is called
from BL3-1 resident in RW memory. The constant FIRST_RESET_HANDLER_CALL is used
to identify whether this is the first version of the reset handler code to be
executed or an overridden version of the code.

The Cortex-A57 errata workarounds are applied only if they have not already been
applied.

Fixes ARM-software/tf-issue#275

Change-Id: Id295f106e4fda23d6736debdade2ac7f2a9a9053

This patch extends the build option `USE_COHERENT_MEMORY` to
conditionally remove coherent memory from the memory maps of
all boot loader stages. The patch also adds necessary
documentation for coherent memory removal in firmware-design,
porting and user guides.

Fixes ARM-Software/tf-issues#106

Change-Id: I260e8768c6a5c2efc402f5804a80657d8ce38773

This patch gathers miscellaneous minor fixes to the documentation, and comments
in the source code.

Change-Id: I631e3dda5abafa2d90f464edaee069a1e58b751b
Co-Authored-By: Soby Mathew <soby.mathew@arm.com>
Co-Authored-By: Dan Handley <dan.handley@arm.com>

This patch adds CPU core and cluster power down sequences to the CPU specific
operations framework introduced in a earlier patch. Cortex-A53, Cortex-A57 and
generic AEM sequences have been added. The latter is suitable for the
Foundation and Base AEM FVPs. A pointer to each CPU's operations structure is
saved in the per-cpu data so that it can be easily accessed during power down
seqeunces.

An optional platform API has been introduced to allow a platform to disable the
Accelerator Coherency Port (ACP) during a cluster power down sequence. The weak
definition of this function (plat_disable_acp()) does not take any action. It
should be overriden with a strong definition if the ACP is present on a
platform.

Change-Id: I8d09bd40d2f528a28d2d3f19b77101178778685d

This patch introduces a framework which will allow CPUs to perform
implementation defined actions after a CPU reset, during a CPU or cluster power
down, and when a crash occurs. CPU specific reset handlers have been implemented
in this patch. Other handlers will be implemented in subsequent patches.

Also moved cpu_helpers.S to the new directory lib/cpus/aarch64/.

Change-Id: I1ca1bade4d101d11a898fb30fea2669f9b37b956

This patch disables routing of external aborts from lower exception levels to
EL3 and ensures that a SError interrupt generated as a result of execution in
EL3 is taken locally instead of a lower exception level.

The SError interrupt is enabled in the TSP code only when the operation has not
been directly initiated by the normal world. This is to prevent the possibility
of an asynchronous external abort which originated in normal world from being
taken when execution is in S-EL1.

Fixes ARM-software/tf-issues#153

Change-Id: I157b996c75996d12fd86d27e98bc73dd8bce6cd5

The purpose of platform_is_primary_cpu() is to determine after reset
(BL1 or BL3-1 with reset handler) if the current CPU must follow the
cold boot path (primary CPU), or wait in a safe state (secondary CPU)
until the primary CPU has finished the system initialization.

This patch removes redundant calls to platform_is_primary_cpu() in
subsequent bootloader entrypoints since the reset handler already
guarantees that code is executed exclusively on the primary CPU.

Additionally, this patch removes the weak definition of
platform_is_primary_cpu(), so the implementation of this function
becomes mandatory. Removing the weak symbol avoids other
bootloaders accidentally picking up an invalid definition in case the
porting layer makes the real function available only to BL1.

The define PRIMARY_CPU is no longer mandatory in the platform porting
because platform_is_primary_cpu() hides the implementation details
(for instance, there may be platforms that report the primary CPU in
a system register). The primary CPU definition in FVP has been moved
to fvp_def.h.

The porting guide has been updated accordingly.

Fixes ARM-software/tf-issues#219

Change-Id: If675a1de8e8d25122b7fef147cb238d939f90b5e

This patch reworks the crash reporting mechanism to further
optimise the stack and code size. The reporting makes use
of assembly console functions to avoid calling C Runtime
to report the CPU state. The crash buffer requirement is
reduced to 64 bytes with this implementation. The crash
buffer is now part of per-cpu data which makes retrieving
the crash buffer trivial.

Also now panic() will use crash reporting if
invoked from BL3-1.

Fixes ARM-software/tf-issues#199

Change-Id: I79d27a4524583d723483165dc40801f45e627da5

This patch reworks the manner in which the M,A, C, SA, I, WXN & EE bits of
SCTLR_EL3 & SCTLR_EL1 are managed. The EE bit is cleared immediately after reset
in EL3. The I, A and SA bits are set next in EL3 and immediately upon entry in
S-EL1. These bits are no longer managed in the blX_arch_setup() functions. They
do not have to be saved and restored either. The M, WXN and optionally the C
bit are set in the enable_mmu_elX() function. This is done during both the warm
and cold boot paths.

Fixes ARM-software/tf-issues#226

Change-Id: Ie894d1a07b8697c116960d858cd138c50bc7a069

This patch reworks the cold boot path across the BL1, BL2, BL3-1 and BL3-2 boot
loader stages to not use stacks allocated in coherent memory for early platform
setup and enabling the MMU. Stacks allocated in normal memory are used instead.

Attributes for stack memory change from nGnRnE when the MMU is disabled to
Normal WBWA Inner-shareable when the MMU and data cache are enabled. It is
possible for the CPU to read stale stack memory after the MMU is enabled from
another CPUs cache. Hence, it is unsafe to turn on the MMU and data cache while
using normal stacks when multiple CPUs are a part of the same coherency
domain. It is safe to do so in the cold boot path as only the primary cpu
executes it. The secondary cpus are in a quiescent state.

This patch does not remove the allocation of coherent stack memory. That is done
in a subsequent patch.

Change-Id: I12c80b7c7ab23506d425c5b3a8a7de693498f830

This patch reworks FVP specific code responsible for determining
the entry point information for BL3-2 and BL3-3 stages when BL3-1
is configured as the reset handler.

Change-Id: Ia661ff0a6a44c7aabb0b6c1684b2e8d3642d11ec

The crash reporting support and early initialisation of the
cpu_data allow the runtime_exception vectors to be used from
the start in BL3-1, removing the need for the additional
early_exception vectors and 2KB of code from BL3-1.

Change-Id: I5f8997dabbaafd8935a7455910b7db174a25d871

This patch prepares the per-cpu pointer cache for wider use by:
* renaming the structure to cpu_data and placing in new header
* providing accessors for this CPU, or other CPUs
* splitting the initialization of the TPIDR pointer from the
  initialization of the cpu_data content
* moving the crash stack initialization to a crash stack function
* setting the TPIDR pointer very early during boot

Change-Id: Icef9004ff88f8eb241d48c14be3158087d7e49a3

This patch adds a common handler for FIQ and IRQ exceptions in the
BL3-1 runtime exception vector table. This function determines the
interrupt type and calls its handler. A crash is reported if an
inconsistency in the interrupt management framework is detected. In
the event of a spurious interrupt, execution resumes from the
instruction where the interrupt was generated.

This patch also removes 'cm_macros.S' as its contents have been moved
to 'runtime_exceptions.S'

Change-Id: I3c85ecf8eaf43a3fac429b119ed0bd706d2e2093

This change adds optional reset vector support to BL3-1
which means BL3-1 entry point can detect cold/warm boot,
initialise primary cpu, set up cci and mail box.

When using BL3-1 as a reset vector it is assumed that
the BL3-1 platform code can determine the location of
the BL3-2 images, or load them as there are no parameters
that can be passed to BL3-1 at reset.

It also fixes the incorrect initialisation of mailbox
registers on the FVP platform

This feature can be enabled by building the code with
make variable RESET_TO_BL31 set as 1

Fixes ARM-software/TF-issues#133
Fixes ARM-software/TF-issues#20

Change-Id: I4e23939b1c518614b899f549f1e8d412538ee570