GitLab

- Remove references to removed build options.
- Remove support for legacy GIC driver.
- Remove support for LOAD_IMAGE_V2=0.

Change-Id: I72f8c05620bdf4a682765e6e53e2c04ca749a3d5
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

A cache flush is added in BL1, in Mbed TLS shared heap code. Thus, we
ensure that the heap info written to the DTB always gets written back to
memory.  Hence, sharing this info with other images is guaranteed.

Change-Id: I0faada31fe7a83854cd5e2cf277ba519e3f050d5
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

In Mbed TLS shared heap code, an additional sanity check is introduced
in BL2. Currently, when BL2 shares heap with BL1, it expects the heap
info to be found in the DTB. If for any reason the DTB is missing, BL2
cannot have the heap address and, hence, Mbed TLS cannot proceed. So,
BL2 cannot continue executing and it will eventually crash.  With this
change we ensure that if the DTB is missing BL2 will panic() instead of
having an unpredictable crash.

Change-Id: I3045ae43e54b7fe53f23e7c2d4d00e3477b6a446
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

This patch introduces the shared Mbed TLS heap optimisation for Arm
platforms. The objective is the Mbed TLS heap to be shared between BL1
and BL2 so as to not allocate the heap memory twice. To achieve that,
the patch introduces all the necessary helpers for implementing this
optimisation. It also applies it for FVP.

Change-Id: I6d85eaa1361517b7490956b2ac50f5fa0d0bb008
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

Small patch which removes some redundant casts to (void *).

Change-Id: If1cfd68f2989bac1d39dbb3d1c31d4119badbc21
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

In Arm platforms, when using dynamic configuration, the necessary
parameters are made available as a DTB. The DTB is loaded by BL1 and,
later on, is parsed by BL1, BL2 or even both, depending on when
information from the DTB is needed.

When the DTB is going to be parsed, it must be validated first, to
ensure that it is properly structured. If an invalid DTB is detected
then:
  - BL1 prints a diagnostic but allows execution to continue,
  - BL2 prints a diagnostic and panics.

Now the behaviour of BL1 is changed so for it also to panic. Thus, the
behaviour of BL1 and BL2 is now similar.

Keep in mind that if BL1 only loads the DTB but it doesn't need to
read/write it, then it doesn't validate it. The validation is done only
when the DTB is actually going to be accessed.

Change-Id: Idcae6092e6dbeab7248dd5e041d6cbb7784fe410
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

The patch changes the layout of BL images in memory to enable
more efficient use of available space. Previously BL31 was loaded
with the expectation that BL2 memory would be reclaimed by BL32
loaded in SRAM. But with increasing memory requirements in the
firmware, we can no longer fit BL32 in SRAM anymore which means the
BL2 memory is not reclaimed by any runtime image. Positioning BL2
below BL1-RW and above BL31 means that the BL31 NOBITS can be
overlaid on BL2 and BL1-RW.

This patch also propogates the same memory layout to BL32 for AArch32
mode. The reset addresses for the following configurations are also
changed :
   * When RESET_TO_SP_MIN=1 for BL32 in AArch32 mode
   * When BL2_AT_EL3=1 for BL2

The restriction on BL31 to be only in DRAM when SPM is enabled
is now removed with this change. The update to the firmware design
guide for the BL memory layout is done in the following patch.

Change-Id: Icca438e257abe3e4f5a8215f945b9c3f9fbf29c9
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch adds soc_fw_config, tos_fw_config and nt_fw_config to the FVP.
The config files are placeholders and do not have any useful bindings
defined. The tos_fw_config is packaged in FIP and loaded by BL2 only
if SPD=tspd. The load address of these configs are specified in tb_fw_config
via new bindings defined for these configs. Currently, in FVP, the
soc_fw_config and tos_fw_config is loaded in the page between BL2_BASE
and ARM_SHARED_RAM. This memory was typically used for BL32 when
ARM_TSP_RAM_LOCATION=tsram but since we cannot fit BL32 in that
space anymore, it should be safe to use this memory for these configs.
There is also a runtime check in arm_bl2_dyn_cfg_init() which ensures
that this overlap doesn't happen.

The previous arm_dyn_get_hwconfig_info() is modified to accept configs
other than hw_config and hence renamed to arm_dyn_get_config_load_info().
The patch also corrects the definition of ARM_TB_FW_CONFIG_LIMIT to be
BL2_BASE.

Change-Id: I03a137d9fa1f92c862c254be808b8330cfd17a5a
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch adds capability to FVP to disable authentication dynamically
via the `disable_auth` property in TB_FW_CONFIG. Both BL1 and BL2 parses
the TB_FW_CONFIG for the `disable_auth` property and invokes the
`load_dyn_disable_auth()` API to disable authentication if the
property is set to 1. The DYN_DISABLE_AUTH is enabled by default for
FVP as it is a development platform. Note that the TB_FW_CONFIG has to
be authenticated by BL1 irrespective of these settings.

The arm_bl2_dyn_cfg_init() is now earlier in bl2_plat_preload_setup()
rather than in bl2_platform_setup() as we need to get the value of
`disable_auth` property prior to authentication of any image by BL2.

Change-Id: I734acd59572849793e5020ec44c6ac51f654a4d1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Change-Id: I1d85b76af002b8b672fcaeca94939b7420bc8243
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

The patch adds the necessary changes to load HW_CONFIG in BL2 for
ARM Platforms :

1. The load address of HW_CONFIG is specified via the `hw_config_addr`
property in TB_FW_CONFIG is loaded by BL1. The `hw_config_max_size`
property defines the maximum size to be expected for the HW_CONFIG.
The `arm_dyn_cfg_helpers.c` and corresponding header implements
utility functions to parse these DT properties defined.
The `arm_dyn_cfg.c` implements wrappers to these helpers to enable
them to be invoked from ARM platform layer.

2. `HW_CONFIG` is added to the `bl2_mem_params_descs[]` array which is
the list of images to be loaded by BL2.

3. The `libfdt` sources are now included when BL2 is built

4. A new helper `populate_next_bl_params_config()` is introduced in
desc_image_load.c to populate the subsequent executable BL images
with the `hw_config` and the corresponding `fw_config` if available.
The `plat_get_next_bl_params()` API for ARM platforms is modified to
invoke this new helper.

5. The implementation of `bl2_early_platform_setup2()` is modified to
consider `arg0` as well in addition to `arg1` passed from BL1.

6. Bump up the BL2 size for Juno to accommodate the inclusion of libfdt.

Change-Id: I80f1554adec41753e0d179a5237364f04fe13a3f
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch modifies the bl1_platform_setup() API to load and authenticate
TB_FW_CONFIG in BL1. The load address of the same is passed on to BL2 in
`arg0` of entrypoint info. The fvp_io_storage.c and arm_io_storage.c also
adds entries corresponding to TB_FW_CONFIG. A helper function
`arm_load_tb_fw_config()` is added to load and authenticate TB_FW_CONFIG
if present.

Change-Id: Ie7bce667b3fad2b1a083bbcbc0a773f9f04254b1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>