GitLab

BL31 binary size is aligned to 4KB because of the
code in include\plat\arm\common\arm_reclaim_init.ld.S:
    __INIT_CODE_UNALIGNED__ = .;
    . = ALIGN(PAGE_SIZE);
    __INIT_CODE_END__ = .;
with all the zero data after the last instruction of
BL31 code to the end of the page.
This causes increase in size of BL31 binary stored in FIP
and its loading time by BL2.
This patch reduces the size of BL31 image by moving
page alignment from __INIT_CODE_END__ to __STACKS_END__
which also increases the stack size for secondary CPUs.

Change-Id: Ie2ec503fc774c22c12ec506d74fd3ef2b0b183a9
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

Provide manifest and build options to boot OP-TEE as a
guest S-EL1 Secure Partition on top of Hafnium in S-EL2.

Increase ARM_SP_MAX_SIZE to cope with OP-TEE debug build image.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: Idd2686fa689a78fe2d05ed92b1d23c65e2edd4cb

In BL2, fw_config's population happened before the cache gets
enabled.
Hence to boost the performance, moved fw_config's population
after cache gets enabled (i.e. after MMU gets enabled).
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I2e75cabd76b1cb7a660f6b72f409ab40d2877284

This patch adds support for Measured Boot driver functionality
in common Arm platform code.

Change-Id: If049dcf8d847c39023b77c0d805a8cf5b8bcaa3e
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

Included cot_descriptors.dtsi in platform device tree
(fvp_tb_fw_config.dts).

Also, updated the maximum size of tb_fw_config to 0x1800
in order to accomodate the device tree for CoT descriptors.

Follow up patch will parse the device tree for these CoT descriptors
and fill the CoT descriptor structures at runtime instead of using
static CoT descriptor structures in the code base.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I90122bc713f6842b82fb019b04caf42629b4f45a

Increased the size of firmware configuration area to accommodate
all configs.

Updated maximum size of following bootloaders due to increase
in firmware configs size and addition of the code in the BL2.

1. Increased maximum size of BL2 for Juno platform in no
   optimisation case.
2. Reduced maximum size of BL31 for fvp and Juno platform.
3. Reduced maximum size of BL32 for Juno platform.

Change-Id: Ifba0564df0d1fe86175bed9fae87fdcf013b1831
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>

Modified the code to do below changes:

1. Load tb_fw_config along with fw_config by BL1.
2. Populate fw_config device tree information in the
   BL1 to load tb_fw_config.
3. In BL2, populate fw_config information to retrieve
   the address of tb_fw_config and then tb_fw_config
   gets populated using retrieved address.
4. Avoid processing of configuration file in case of error
   value returned from "fw_config_load" function.
5. Updated entrypoint information for BL2 image so
   that it's arg0 should point to fw_config address.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Change-Id: Ife6f7b673a074e7f544ee3d1bda7645fd5b2886c

Cleaned up confused naming between TB_FW and FW_CONFIG.
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I9e9f6e6ca076d38fee0388f97d370431ae067f08

Using the fconf framework, the Group 0 and Group 1 secure interrupt
descriptors are moved to device tree and retrieved in runtime. This
feature is enabled by the build flag SEC_INT_DESC_IN_FCONF.

Change-Id: I360c63a83286c7ecc2426cd1ff1b4746d61e633c
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

The patch fixes BL31 linker script error
"Init code ends past the end of the stacks"
for platforms with number of CPUs less than 4,
which is caused by __STACKS_END__ address being
lower than __INIT_CODE_END__.
The modified BL31 linker script detects such cases
and increases the total amount of stack memory,
setting __STACKS_END__ = __INIT_CODE_END__, and
CPUs' stacks are calculated by BL31 'plat_get_my_stack'
function accordingly. For platforms with more than 4 CPUs
and __INIT_CODE_END__ < __STACKS_END__ stack memory does not
increase and allocated CPUs' stacks match the existing
implementation.
The patch removes exclusion of PSCI initialization
functions from the reclaimed .init section in
'arm_reclaim_init.ld.S' script, which increases the
size of reclaimed memory region.

Change-Id: I927773e00dd84e1ffe72f9ee534f4f2fc7b6153c
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

This patch introduces dynamic configuration for SDEI setup and is supported
when the new build flag SDEI_IN_FCONF is enabled. Instead of using C arrays
and processing the configuration at compile time, the config is moved to
dts files. It will be retrieved at runtime during SDEI init, using the fconf
layer.

Change-Id: If5c35a7517ba00a9f258d7f3e7c8c20cee169a31
Signed-off-by: Balint Dobszay <balint.dobszay@arm.com>
Co-authored-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

The platform io policies array is now always accessed through a fconf getter.
This gives us an ideal spot to check for out-of-bound accesses.

Remove the assertion in plat_get_image_source(), which is now redundant.

Change-Id: Iefe808d530229073b68cbd164d927b8b6662a217
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

Moved SMCCC defines from plat_arm.h to new <smccc_def.h> header
and include this header in all ARM platforms.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I4cbc69c7b9307461de87b7c7bf200dd9b810e485

This patch provides support for measured boot by adding calculation
of BL2 image hash in BL1 and writing these data in TB_FW_CONFIG DTB.

Change-Id: Ic074a7ed19b14956719c271c805b35d147b7cec1
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

Implemented SMCCC_ARCH_SOC_ID call in order to get below
SOC information:

1. SOC revision
2. SOC version

Implementation done using below SMCCC specification document:
https://developer.arm.com/docs/den0028/c

Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ie0595f1c345a6429a6fb4a7f05534a0ca9c9a48b

Necessary infrastructure added to integrate fconf framework in BL31 & SP_MIN.
Created few populator() functions which parse HW_CONFIG device tree
and registered them with fconf framework. Many of the changes are
only applicable for fvp platform.

This patch:
1. Adds necessary symbols and sections in BL31, SP_MIN linker script
2. Adds necessary memory map entry for translation in BL31, SP_MIN
3. Creates an abstraction layer for hardware configuration based on
   fconf framework
4. Adds necessary changes to build flow (makefiles)
5. Minimal callback to read hw_config dtb for capturing properties
   related to GIC(interrupt-controller node)
6. updates the fconf documentation

Change-Id: Ib6292071f674ef093962b9e8ba0d322b7bf919af
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

This patch implements loading of Secure Partition packages using
existing framework of loading other bl images.

The current framework uses a statically defined array to store all the
possible image types and at run time generates a link list and traverse
through it to load different images.

To load SPs, a new array of fixed size is introduced which will be
dynamically populated based on number of SPs available in the system
and it will be appended to the loadable images list.

Change-Id: I8309f63595f2a71b28a73b922d20ccba9c4f6ae4
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>

Use the firmware configuration framework to retrieve information about
Secure Partitions to facilitate loading them into memory.

To load a SP image we need UUID look-up into FIP and the load address
where it needs to be loaded in memory.

This patch introduces a SP populator function which gets UUID and load
address from firmware config device tree and updates its C data
structure.

Change-Id: I17faec41803df9a76712dcc8b67cadb1c9daf8cd
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>

This patch introduces a build flag which allows the xlat tables
to be mapped in a read-only region within BL31 memory. It makes it
much harder for someone who has acquired the ability to write to
arbitrary secure memory addresses to gain control of the
translation tables.

The memory attributes of the descriptors describing the tables
themselves are changed to read-only secure data. This change
happens at the end of BL31 runtime setup. Until this point, the
tables have read-write permissions. This gives a window of
opportunity for changes to be made to the tables with the MMU on
(e.g. reclaiming init code). No changes can be made to the tables
with the MMU turned on from this point onwards. This change is also
enabled for sp_min and tspd.

To make all this possible, the base table was moved to .rodata. The
penalty we pay is that now .rodata must be aligned to the size of
the base table (512B alignment). Still, this is better than putting
the base table with the higher level tables in the xlat_table
section, as that would cost us a full 4KB page.

Changing the tables from read-write to read-only cannot be done with
the MMU on, as the break-before-make sequence would invalidate the
descriptor which resolves the level 3 page table where that very
descriptor is located. This would make the translation required for
writing the changes impossible, generating an MMU fault.

The caches are also flushed.
Signed-off-by: Petre-Ionut Tudor <petre-ionut.tudor@arm.com>
Change-Id: Ibe5de307e6dc94c67d6186139ac3973516430466

The cookie will be leveraged in the next commit.

Change-Id: Ie8bad275d856d84c27466461cf815529dd860446
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

For platforms that have two or more TZC400 controllers instantiated,
allow the TZC400 driver to be usable with all those instances.
This is achieved by allowing 'arm_tzc400_setup' function to accept
the base address of the TZC400 controller.

Change-Id: I4add470e6ddb58432cd066145e644112400ab924
Signed-off-by: Suyash Pathak <suyash.pathak@arm.com>

The base address for second DRAM varies across different platforms.
So allow platforms to define second DRAM by moving Juno/SGM-775 specific
definition of second DRAM base address to Juno/SGM-775 board definition
respectively, SGI/RD specific definition of DRAM 2 base address to SGI
board definition.

Change-Id: I0ecd3a2bd600b6c7019c7f06f8c452952bd07cae
Signed-off-by: Suyash Pathak <suyash.pathak@arm.com>

A TZC400 can have upto 4 filters and the number of filters instantiated
within a TZC400 is platform dependent. So allow platforms to define the
value of PLAT_ARM_TZC_FILTERS by moving the existing Juno specific
definition of PLAT_ARM_TZC_FILTERS to Juno board definitions.

Change-Id: I67a63d7336595bbfdce3163f9a9473e15e266f40
Signed-off-by: Suyash Pathak <suyash.pathak@arm.com>

This patch reserves and maps the Trusted DRAM for SPM core execution.
It also configures the TrustZone address space controller to run BL31
in secure DRAM.
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Change-Id: I7e1bb3bbc61a0fec6a9cb595964ff553620c21dc

On systems that have multiple platform components that can interpret the
SCMI messages, there is a need to support multiple SCMI channels (one
each to those platform components). Extend the existing SCMI interface
that currently supports only a single SCMI channel to support multiple
SCMI channels.

Change-Id: Ice4062475b903aef3b5e5bc37df364c9778a62c5
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

Multi-chip platforms have two or more identical chips connected using a
high speed coherent link. In order to identify such platforms,
add chip_id and multi_chip_mode information in the platform variant
info structure. The values of these two new elements is populated
during boot.

Change-Id: Ie6e89cb33b3f0f408814f6239cd06647053e23ed
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>

Currently, an IO setup failure will be ignored on arm platform release
build. Change this to panic instead.

Change-Id: I027a045bce2422b0a0fc4ff9e9d4c6e7bf5d2f98
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

Change the return type of "arm_io_is_toc_valid()" and
"plat_arm_bl1_fwu_needed()" to bool, to match function behavior.

Change-Id: I503fba211219a241cb263149ef36ca14e3362a1c
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

Use the firmware configuration framework to store the io_policies
information inside the configuration device tree instead of the static
structure in the code base.

The io_policies required by BL1 can't be inside the dtb, as this one is
loaded by BL1, and only available at BL2.

This change currently only applies to FVP platform.

Change-Id: Ic9c1ac3931a4a136aa36f7f58f66d3764c1bfca1
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

Use the firmware configuration framework in arm dynamic configuration
to retrieve mbedtls heap information between bl1 and bl2.

For this, a new fconf getter is added to expose the device tree base
address and size.

Change-Id: Ifa5ac9366ae100e2cdd1f4c8e85fc591b170f4b6
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

Use fconf to retrieve the `disable_authentication` property.
Move this access from arm dynamic configuration to bl common.

Change-Id: Ibf184a5c6245d04839222f5457cf5e651f252b86
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

This patch introduces a better separation between the trusted-boot
related properties, and the dynamic configuration DTBs loading
information.

The dynamic configuration DTBs properties are moved to a new node:
`dtb-registry`. All the sub-nodes present will be provided to the
dynamic config framework to be loaded. The node currently only contains
the already defined configuration DTBs, but can be extended for future
features if necessary.
The dynamic config framework is modified to use the abstraction provided
by the fconf framework, instead of directly accessing the DTBs.

The trusted-boot properties are kept under the "arm,tb_fw" compatible
string, but in a separate `tb_fw-config` node.
The `tb_fw-config` property of the `dtb-registry` node simply points
to the load address of `fw_config`, as the `tb_fw-config` is currently
part of the same DTB.

Change-Id: Iceb6c4c2cb92b692b6e28dbdc9fb060f1c46de82
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

Move the loading of the dtb from arm_dym_cfg to fconf. The new loading
function is not associated to arm platform anymore, and can be moved
to bl_main if wanted.

Change-Id: I847d07eaba36d31d9d3ed9eba8e58666ea1ba563
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

Enables usage of ARM_ROTPK_LOCATION=regs for FVP board.
Removes hard-coded developer keys. Instead, setting
ARM_ROTPK_LOCATION=devel_* takes keys from default directory.
In case of ROT_KEY specified - generates a new hash and replaces the
original.

Note: Juno board was tested by original feature author and was not tested
for this patch since we don't have access to the private key. Juno
implementation was moved to board-specific file without changing
functionality. It is not known whether byte-swapping is still needed
for this platform.

Change-Id: I0fdbaca0415cdcd78f3a388551c2e478c01ed986
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>

In order to support SEPARATE_NOBITS_REGION for Arm platforms, we need to load
BL31 PROGBITS into secure DRAM space and BL31 NOBITS into SRAM. Hence mandate
the build to require that ARM_BL31_IN_DRAM is enabled as well.

Naturally with SEPARATE_NOBITS_REGION enabled, the BL31 initialization code
cannot be reclaimed to be used for runtime data such as secondary cpu stacks.

Memory map for BL31 NOBITS region also has to be created.

Change-Id: Ibbc8c9499a32e63fd0957a6e254608fbf6fa90c9
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

This reverts commit d433bbdd.

Change-Id: I46c69dce704a1ce1b50452dd4d62425c4a67f7f0

In order to support SEPARATE_NOBITS_REGION for Arm platforms, we need to load
BL31 PROGBITS into secure DRAM space and BL31 NOBITS into SRAM. Hence mandate
the build to require that ARM_BL31_IN_DRAM is enabled as well.

Naturally with SEPARATE_NOBITS_REGION enabled, the BL31 initialization code
cannot be reclaimed to be used for runtime data such as secondary cpu stacks.

Memory map for BL31 NOBITS region also has to be created.

Change-Id: Ibd480f82c1dc74e9cbb54eec07d7a8fecbf25433
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

NOTE for platform integrators:
   API `plat_psci_stat_get_residency()` third argument
   `last_cpu_idx` is changed from "signed int" to the
   "unsigned int" type.

Issue / Trouble points
1. cpu_idx is used as mix of `unsigned int` and `signed int` in code
with typecasting at some places leading to coverity issues.

2. Underlying platform API's return cpu_idx as `unsigned int`
and comparison is performed with platform specific defines
`PLAFORM_xxx` which is not consistent

Misra Rule 10.4:
The value of a complex expression of integer type may only be cast to
a type that is narrower and of the same signedness as the underlying
type of the expression.

Based on above points, cpu_idx is kept as `unsigned int` to match
the API's and low-level functions and platform defines are updated
where ever required
Signed-off-by: Deepika Bhavnani <deepika.bhavnani@arm.com>
Change-Id: Ib26fd16e420c35527204b126b9b91e8babcc3a5c

The Secure Partition Manager (SPM) prototype implementation is
being removed. This is preparatory work for putting in place a
dispatcher component that, in turn, enables partition managers
at S-EL2 / S-EL1.

This patch removes:

- The core service files (std_svc/spm)
- The Resource Descriptor headers (include/services)
- SPRT protocol support and service definitions
- SPCI protocol support and service definitions

Change-Id: Iaade6f6422eaf9a71187b1e2a4dffd7fb8766426
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>

There are two different implementations of Secure Partition
management in TF-A. One is based on the "Management Mode" (MM)
design, the other is based on the Secure Partition Client Interface
(SPCI) specification. Currently there is a dependency between their
build flags that shouldn't exist, making further development
harder than it should be. This patch removes that
dependency, making the two flags function independently.

Before: ENABLE_SPM=1 is required for using either implementation.
        By default, the SPCI-based implementation is enabled and
        this is overridden if SPM_MM=1.

After: ENABLE_SPM=1 enables the SPCI-based implementation.
       SPM_MM=1 enables the MM-based implementation.
       The two build flags are mutually exclusive.

Note that the name of the ENABLE_SPM flag remains a bit
ambiguous - this will be improved in a subsequent patch. For this
patch the intention was to leave the name as-is so that it is
easier to track the changes that were made.

Change-Id: I8e64ee545d811c7000f27e8dc8ebb977d670608a
Signed-off-by: Paul Beesley <paul.beesley@arm.com>