GitLab

This patch introduces the following three platform interfaces:

* void plat_psci_stat_accounting_start(const psci_power_state_t *state_info)

  This is an optional hook that platforms can implement in order
  to perform accounting before entering a low power state.  This
  typically involves capturing a timestamp.

* void plat_psci_stat_accounting_stop(const psci_power_state_t *state_info)

  This is an optional hook that platforms can implement in order
  to perform accounting after exiting from a low power state.  This
  typically involves capturing a timestamp.

* u_register_t plat_psci_stat_get_residency(unsigned int lvl,
	const psci_power_state_t *state_info,
	unsigned int last_cpu_index)

  This is an optional hook that platforms can implement in order
  to calculate the PSCI stat residency.

If any of these interfaces are overridden by the platform, it is
recommended that all of them are.

By default `ENABLE_PSCI_STAT` is disabled.  If `ENABLE_PSCI_STAT`
is set but `ENABLE_PMF` is not set then an alternative PSCI stat
collection backend must be provided.  If both are set, then default
weak definitions of these functions are provided, using PMF to
calculate the residency.

NOTE: Previously, platforms did not have to explicitly set
`ENABLE_PMF` since this was automatically done by the top-level
Makefile.

Change-Id: I17b47804dea68c77bc284df15ee1ccd66bc4b79b
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

AEMv8-A Model release v8.2 has been made available and Trusted Firmware
has been tested against these versions as part of its CI system. This
patch updates the user guide documentation to reflect the version of AEM
and Cortex Models that Trusted Firmware has been tested against.

Also, the Linaro Release Notes link was broken and this patch updates the
link.

Change-Id: I88729cef909a69fff629036f480fd6168ad7dc9a
Signed-off-by: David Cunado <david.cunado@arm.com>

RESET_TO_BL31=1 is specified by plat/xilinx/zynqmp/platform.mk with
"override" directive.  So, RESET_TO_BL31=1 is guaranteed without any
operation on users' side.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The errata reporting policy is as follows:

  - If an errata workaround is enabled:

    - If it applies (i.e. the CPU is affected by the errata), an INFO
      message is printed, confirming that the errata workaround has been
      applied.

    - If it does not apply, a VERBOSE message is printed, confirming
      that the errata workaround has been skipped.

  - If an errata workaround is not enabled, but would have applied had
    it been, a WARN message is printed, alerting that errata workaround
    is missing.

The CPU errata messages are printed by both BL1 (primary CPU only) and
runtime firmware on debug builds, once for each CPU/errata combination.

Relevant output from Juno r1 console when ARM Trusted Firmware is built
with PLAT=juno LOG_LEVEL=50 DEBUG=1:

  VERBOSE: BL1: cortex_a57: errata workaround for 806969 was not applied
  VERBOSE: BL1: cortex_a57: errata workaround for 813420 was not applied
  INFO:    BL1: cortex_a57: errata workaround for disable_ldnp_overread was applied
  WARNING: BL1: cortex_a57: errata workaround for 826974 was missing!
  WARNING: BL1: cortex_a57: errata workaround for 826977 was missing!
  WARNING: BL1: cortex_a57: errata workaround for 828024 was missing!
  WARNING: BL1: cortex_a57: errata workaround for 829520 was missing!
  WARNING: BL1: cortex_a57: errata workaround for 833471 was missing!
  ...
  VERBOSE: BL31: cortex_a57: errata workaround for 806969 was not applied
  VERBOSE: BL31: cortex_a57: errata workaround for 813420 was not applied
  INFO:    BL31: cortex_a57: errata workaround for disable_ldnp_overread was applied
  WARNING: BL31: cortex_a57: errata workaround for 826974 was missing!
  WARNING: BL31: cortex_a57: errata workaround for 826977 was missing!
  WARNING: BL31: cortex_a57: errata workaround for 828024 was missing!
  WARNING: BL31: cortex_a57: errata workaround for 829520 was missing!
  WARNING: BL31: cortex_a57: errata workaround for 833471 was missing!
  ...
  VERBOSE: BL31: cortex_a53: errata workaround for 826319 was not applied
  INFO:    BL31: cortex_a53: errata workaround for disable_non_temporal_hint was applied

Also update documentation.

Change-Id: Iccf059d3348adb876ca121cdf5207bdbbacf2aba
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The current user guide mentions that Foundation model doesn't support
debugger interface. Clarify that all FVPs support --cadi-server option
such that a CADI-compliant debugger can connect to and control model
execution.

Also fix broken URL to FVP home page.

Change-Id: Ia14d618a4e0abb4b228eb1616040f9b51fb3f6f9
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

 - Clarify the documentation of the 'FWU_SMC_IMAGE_COPY' SMC in the
   Firmware Update guide. Also extend the list of pre-conditions to
   include the additional input validation implemented by previous
   patches.

 - Improve documentation of bl1_plat_mem_check() in the porting
   guide. It now specifies that the generic FWU code protects
   bl1_plat_mem_check() from integer overflows resulting from
   the addition of the base address and size passed in arguments.

Change-Id: I07b47a3778df7b9c089529b2dd2135707640a91c
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

Foundation Model release 10.2 has been made available and Trusted
Firmware has been tested against that it as part of its CI system.

This patch updates the user guide documentation to reflect the version
of Foundation Model that Trusted Firmware has been tested against.

Change-Id: I8571e1027b24892b41d04b93b24245a371ca2cae
Signed-off-by: David Cunado <david.cunado@arm.com>

Various CPU drivers in ARM Trusted Firmware register functions to handle
power-down operations. At present, separate functions are registered to
power down individual cores and clusters.

This scheme operates on the basis of core and cluster, and doesn't cater
for extending the hierarchy for power-down operations. For example,
future CPUs might support multiple threads which might need powering
down individually.

This patch therefore reworks the CPU operations framework to allow for
registering power down handlers on specific level basis. Henceforth:

  - Generic code invokes CPU power down operations by the level
    required.

  - CPU drivers explicitly mention CPU_NO_RESET_FUNC when the CPU has no
    reset function.

  - CPU drivers register power down handlers as a list: a mandatory
    handler for level 0, and optional handlers for higher levels.

All existing CPU drivers are adapted to the new CPU operations framework
without needing any functional changes within.

Also update firmware design guide.

Change-Id: I1826842d37a9e60a9e85fdcee7b4b8f6bc1ad043
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The previous code required that a certificate be signed with the ROT
key before the platform's NV counter could be updated with the value
in the certificate.  This implies that the Non-Trusted NV counter was
not being updated for Non-Trusted content certificates, as they cannot
be signed with the ROT key in the TBBR CoT scheme.

The code is reworked to only allow updating the platform's Trusted NV
counter when a certificate protected by the Trusted NV counter is
signed with the ROT key.

Content certificates protected by the Non-Trusted NV counter are
allowed to update the platform's Non-Trusted NV counter, assuming
that the certificate value is higher than the platform's value.

A new optional platform API has been introduced, named
plat_set_nv_ctr2().  Platforms may choose to implement it and perform
additional checks based on the authentication image descriptor before
modifying the NV counters.  A default weak implementation is available
that just calls into plat_set_nv_ctr().

Fixes ARM-software/tf-issues#426

Change-Id: I4fc978fd28a3007bc0cef972ff1f69ad0413b79c
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

Added the definitions `PLAT_PHY_ADDR_SPACE_SIZE` and
`PLAT_VIRT_ADDR_SPACE_SIZE` which specify respectively the physical
and virtual address space size a platform can use.

`ADDR_SPACE_SIZE` is now deprecated. To maintain compatibility, if any
of the previous defines aren't present, the value of `ADDR_SPACE_SIZE`
will be used instead.

For AArch64, register ID_AA64MMFR0_EL1 is checked to calculate the
max PA supported by the hardware and to verify that the previously
mentioned definition is valid. For AArch32, a 40 bit physical
address space is considered.

Added asserts to check for overflows.

Porting guide updated.

Change-Id: Ie8ce1da5967993f0c94dbd4eb9841fc03d5ef8d6
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I28b2790ff2f87b9fe3cf1020e59e1e0a00be6f97
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Add dependency information in the user guide for ARM_RECOM_STATE_ID_ENC
that needs to be set when using PSCI_EXTENDED_STATE_ID on ARM
platforms. Also clarify the build error message.

Change-Id: Id125a0299b179f5f222bca4e2503204bf89a3c59
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

The API description currently states that interrupt handlers
(interrupt_type_handler_t pointers) SHOULD return a pointer
to the target cpu_context.

This patch rewords the description of the interrupts handlers to state
that it MUST return a pointer to the target security context. It also
warns about potential portability issue. Specifically, this pointer is
not used on AArch64 and calls to context library APIs must be used to
ask BL31 to return to a specific context. However, this could change in
the future and interrupt handlers must always return the pointer.

Change-Id: I3f82a046de4d7a5b51a8cbebe7eb2a00dbbdb4f0
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

Fix a link broken by a missing space that turned
it into a link to an non-existent anchor.

Change-Id: Ie863e963db28afa3a28b69d3f63bd7638bdf5af9
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

fixes ARM-Software/tf-issues#346

Change-Id: I946c8eab650bba7407775462ce91f394d767e079
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

This patch adds the secure payload dispatcher for interacting
with Google's Trusty TEE. Documentation for Trusty can be found
at https://source.android.com/security/trusty



Original authors:
-----------------
* Arve Hjønnevåg <arve@android.com>
* Michael Ryleev <gmar@google.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

At present, build options in the user guide aren't listed in any
specific order. Ordering them alphabetically is a standard practice, and
is also easier on the reader.

Contents unchanged.

Change-Id: Ibc36f3a2a576edb86c1a402430d2ef5adcb2f144
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

This patch fixes the type of the return value of bl1_plat_mem_check()
in the porting guide. It also specifies the expected return value.

Change-Id: I7c437342b8bfb1e621d74b2edf0aaf97b913216a
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

Change-Id: I8e50df67e860b9589834445761a7b9927690fdce
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

Do not double the phrase "called with the".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Updated the user guide to clarify building FIP for AArch32.
The instructions were previously specific to building a FIP for AArch64.

Change-Id: I7bd1a6b8e810cfda411f707e04f479006817858e
Signed-off-by: David Cunado <david.cunado@arm.com>

Updated change-log.md with summary of changes since release v1.2.

Change-Id: Ia1e18ff4b0da567cf12dfcb53e6317e995100bdf

Add a Performance Measurement Framework (PMF) section
to the firmware design document.

Change-Id: I5953bd3b1067501f190164c8827d2b0d8022fc0b
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

The user guide incorrectly claimed that it is possible to load a
bootwrapped kernel over JTAG on Juno in the same manner as an EL3
payload. In the EL3 payload boot flow, some of the platform
initialisations in BL2 are modified. In particular, the TZC settings
are modified to allow unrestricted access to DRAM. This in turn allows
the debugger to access the DRAM and therefore to load the image there.

In the BL33-preloaded boot flow though, BL2 uses the default TZC
programming, which prevent access to most of the DRAM from secure state.
When execution reaches the SPIN_ON_BL1_EXIT loop, the MMU is disabled
and thus DS-5 presumably issues secure access transactions while trying
to load the image, which fails.

One way around it is to stop execution at the end of BL2 instead. At
this point, the MMU is still enabled and the DRAM is mapped as
non-secure memory. Therefore, the debugger is allowed to access this
memory in this context and to sucessfully load the bootwrapped kernel in
DRAM. The user guide is updated to suggest this alternative method.
Co-Authored-By: Sandrine Bailleux <sandrine.bailleux@arm.com>
Signed-off-by: Dan Handley <dan.handley@arm.com>

Change-Id: I537ea1c6d2f96edc06bc3f512e770c748bcabe94

This patch adds necessary updates for building and running Trusted
Firmware for AArch32 to user-guide.md. The instructions for running
on both `FVP_Base_AEMv8A-AEMv8A` in AArch32 mode and
`FVP_Base_Cortex-A32x4` models are added. The device tree files for
AArch32 Linux kernel are also added in the `fdts` folder.

Change-Id: I0023b6b03e05f32637cb5765fdeda8c8df2d0d3e

This patch updates the firmware-design.md for AArch32 related changes.

Change-Id: Idf392a44861ab9c1f59f3de4f3435f508b17c678

Fix one of the two titles that ended up being the same, although both
describe different things.

Change-Id: I66ecf369643709898ee4c014659d8f85c0480643

This patch adds the PSCI library integration guide for AArch32 ARMv8-A
systems `psci-lib-integration-guide.md` to the documentation. The
patch also adds appropriate reference to the new document in
the `firmware-design.md` document.

Change-Id: I2d5b5c6b612452371713399702e318e3c73a8ee0

This patch updates the User Guide to recommend the latest version
of some of the software dependencies of ARM Trusted Firmware.

 - Upgrade Linaro release:     16.02 -> 16.06

 - Upgrade FVPs
    - Foundation v8 FVP:       9.5 -> 10.1
    - Base FVPs:               7.6 -> 7.7

 - Upgrade mbed TLS library:   2.2.0 -> 2.2.1

Note that the latest release of mbed TLS as of today is 2.3.0 but it has
compilations issues with the set of library configuration options that
Trusted Firmware uses. 2.2.1 is the next most recent release known to
build with TF.

This patch also fixes the markdown formatting of a link in the
User Guide.

Change-Id: Ieb7dd336f4d3110fba060afec4ad580ae707a8f1

This patch adds common changes to support AArch32 state in
BL1 and BL2. Following are the changes:

* Added functions for disabling MMU from Secure state.
* Added AArch32 specific SMC function.
* Added semihosting support.
* Added reporting of unhandled exceptions.
* Added uniprocessor stack support.
* Added `el3_entrypoint_common` macro that can be
  shared by BL1 and BL32 (SP_MIN) BL stages. The
  `el3_entrypoint_common` is similar to the AArch64
  counterpart with the main difference in the assembly
  instructions and the registers that are relevant to
  AArch32 execution state.
* Enabled `LOAD_IMAGE_V2` flag in Makefile for
  `ARCH=aarch32` and added check to make sure that
  platform has not overridden to disable it.

Change-Id: I33c6d8dfefb2e5d142fdfd06a0f4a7332962e1a3

This patch adds capability to load BL images based on image
descriptors instead of hard coded way of loading BL images.
This framework is designed such that it can be readily adapted
by any BL stage that needs to load images.

In order to provide the above capability the following new
platform functions are introduced:

  bl_load_info_t *plat_get_bl_image_load_info(void);
    This function returns pointer to the list of images that the
    platform has populated to load.

  bl_params_t *plat_get_next_bl_params(void);
    This function returns a pointer to the shared memory that the
    platform has kept aside to pass trusted firmware related
    information that next BL image needs.

  void plat_flush_next_bl_params(void);
    This function flushes to main memory all the params that
    are passed to next image.

  int bl2_plat_handle_post_image_load(unsigned int image_id)
    This function can be used by the platforms to update/use
    image information for given `image_id`.

`desc_image_load.c` contains utility functions which can be used
by the platforms to generate, load and executable, image list
based on the registered image descriptors.

This patch also adds new version of `load_image/load_auth_image`
functions in-order to achieve the above capability.

Following are the changes for the new version as compared to old:
  - Refactor the signature and only keep image_id and image_info_t
    arguments. Removed image_base argument as it is already passed
    through image_info_t. Given that the BL image base addresses and
    limit/size are already provided by the platforms, the meminfo_t
    and entry_point_info arguments are not needed to provide/reserve
    the extent of free memory for the given BL image.

  - Added check for the image size against the defined max size.
    This is needed because the image size could come from an
    unauthenticated source (e.g. the FIP header).
    To make this check, new member is added to the image_info_t
    struct for identifying the image maximum size.

New flag `LOAD_IMAGE_V2` is added in the Makefile.
Default value is 0.

NOTE: `TRUSTED_BOARD_BOOT` is currently not supported when
      `LOAD_IMAGE_V2` is enabled.

Change-Id: Ia7b643f4817a170d5a2fbf479b9bc12e63112e79

Partition driver requires the "PLAT_PARTITION_MAX_ENTRIES" definition.

By default, it's defined to 128 in partition driver. But it costs a lot
of memory, and only a few partition entries are really used in platform
partition table. If user wants use memory efficiently, user should
define the build flag in platform.mk instead.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

This patch adds support for NODE_HW_STATE PSCI API by introducing a new
PSCI platform hook (get_node_hw_state). The implementation validates
supplied arguments, and then invokes this platform-defined hook and
returns its result to the caller. PSCI capabilities are updated
accordingly.

Also updates porting and firmware design guides.

Change-Id: I808e55bdf0c157002a7c104b875779fe50a68a30

This feature allows one to quickly verify that the expected
image is contained in the FIP without extracting the image and
running sha256sum(1) on it.

The sha256 digest is only shown when the verbose flag is used.

This change requires libssl-dev to be installed in order to build
Trusted Firmware. Previously, libssl-dev was optionally needed only
to support Trusted Board Boot configurations.

Fixes ARM-Software/tf-issues#124

Change-Id: Ifb1408d17f483d482bb270a589ee74add25ec5a6

This patch updates the User Guide to move up from version 7.2 to 7.6
of the Base FVP.

Change-Id: I792b2250deb4836266e14b40992ae59a5ab5f729

This patch enables the AArch32 build including SP_MIN in the
top level Makefile. The build flag `ARCH` now can specify either
`aarch64`(default) or `aarch32`. Currently only FVP AEM model is
supported for AArch32 build. Another new build flag `AARCH32_SP`
is introduced to specify the AArch32 secure payload to be built.

Change-Id: Ie1198cb9e52d7da1b79b93243338fc3868b08faa

fiptool provides a more consistent and intuitive interface compared to
the fip_create program.  It serves as a better base to build on more
features in the future.

fiptool supports various subcommands.  Below are the currently
supported subcommands:

1) info   - List the images contained in a FIP file.
2) create - Create a new FIP file with the given images.
3) update - Update an existing FIP with the given images.
4) unpack - Extract a selected set or all the images from a FIP file.
5) remove - Remove images from a FIP file.  This is a new command that
   was not present in fip_create.

To create a new FIP file, replace "fip_create" with "fiptool create".

To update a FIP file, replace "fip_create" with "fiptool update".

To dump the contents of a FIP file, replace "fip_create --dump" with
"fiptool info".

A compatibility script that emulates the basic functionality of
fip_create is provided.  Existing scripts might or might not work with
the compatibility script.  Users are strongly encouraged to migrate to
fiptool.

Fixes ARM-Software/tf-issues#87
Fixes ARM-Software/tf-issues#108
Fixes ARM-Software/tf-issues#361

Change-Id: I7ee4da7ac60179cc83cf46af890fd8bc61a53330

This patch documents the effect, cost and benefits of the
SEPARATE_CODE_AND_RODATA build flag.

Change-Id: Ic8daf0563fa6335930ad6c70b9c35f678e84d39d

Compile option `ARM_BOARD_OPTIMISE_MMAP` has been renamed to
`ARM_BOARD_OPTIMISE_MEM` because it now applies not only to defines
related to the translation tables but to the image size as well.

The defines `PLAT_ARM_MAX_BL1_RW_SIZE`, `PLAT_ARM_MAX_BL2_SIZE` and
`PLAT_ARM_MAX_BL31_SIZE` have been moved to the file board_arm_def.h.
This way, ARM platforms no longer have to set their own values if
`ARM_BOARD_OPTIMISE_MEM=0` and they can specify optimized values
otherwise. The common sizes have been set to the highest values used
for any of the current build configurations.

This is needed because in some build configurations some images are
running out of space. This way there is a common set of values known
to work for all of them and it can be optimized for each particular
platform if needed.

The space reserved for BL2 when `TRUSTED_BOARD_BOOT=0` has been
increased. This is needed because when memory optimisations are
disabled the values for Juno of `PLAT_ARM_MMAP_ENTRIES` and
`MAX_XLAT_TABLES` are higher. If in this situation the code is
compiled in debug mode and with "-O0", the code won't fit.

Change-Id: I70a3d8d3a0b0cad1d6b602c01a7ea334776e718e

This patch introduces the PSCI Library interface. The major changes
introduced are as follows:

* Earlier BL31 was responsible for Architectural initialization during cold
boot via bl31_arch_setup() whereas PSCI was responsible for the same during
warm boot. This functionality is now consolidated by the PSCI library
and it does Architectural initialization via psci_arch_setup() during both
cold and warm boots.

* Earlier the warm boot entry point was always `psci_entrypoint()`. This was
not flexible enough as a library interface. Now PSCI expects the runtime
firmware to provide the entry point via `psci_setup()`. A new function
`bl31_warm_entrypoint` is introduced in BL31 and the previous
`psci_entrypoint()` is deprecated.

* The `smc_helpers.h` is reorganized to separate the SMC Calling Convention
defines from the Trusted Firmware SMC helpers. The former is now in a new
header file `smcc.h` and the SMC helpers are moved to Architecture specific
header.

* The CPU context is used by PSCI for context initialization and
restoration after power down (PSCI Context). It is also used by BL31 for SMC
handling and context management during Normal-Secure world switch (SMC
Context). The `psci_smc_handler()` interface is redefined to not use SMC
helper macros thus enabling to decouple the PSCI context from EL3 runtime
firmware SMC context. This enables PSCI to be integrated with other runtime
firmware using a different SMC context.

NOTE: With this patch the architectural setup done in `bl31_arch_setup()`
is done as part of `psci_setup()` and hence `bl31_platform_setup()` will be
invoked prior to architectural setup. It is highly unlikely that the platform
setup will depend on architectural setup and cause any failure. Please be
be aware of this change in sequence.

Change-Id: I7f497a08d33be234bbb822c28146250cb20dab73