GitLab

BL3-2 image (Secure Payload) is optional. If the image cannot be
loaded a warning message is printed and the boot process continues.
According to the TBBR document, this behaviour should not apply in
case of an authentication error, where the boot process should be
aborted.

This patch modifies the load_auth_image() function to distinguish
between a load error and an authentication error. The caller uses
the return value to abort the boot process or continue.

In case of authentication error, the memory region used to store
the image is wiped clean.

Change-Id: I534391d526d514b2a85981c3dda00de67e0e7992

- Apply a53 errata #826319 to revision <= r0p2
- Apply a53 errata #836870 to revision <= r0p3
- Update docs/cpu-specific-build-macros.md for newly added errata build flags

Change-Id: I44918e36b47dca1fa29695b68700ff9bf888865e
Signed-off-by: Jimmy Huang <jimmy.huang@mediatek.com>

- Add mmio 16 bits read/write functions.
- Add clear/set/clear-and-set utility functions.

Change-Id: I00fdbdf24af537424f8666b1cadaa5f77a2a46ed
Signed-off-by: Jimmy Huang <jimmy.huang@mediatek.com>

Denver is NVIDIA's own custom-designed, 64-bit, dual-core CPU which is
fully ARMv8 architecture compatible.  Each of the two Denver cores
implements a 7-way superscalar microarchitecture (up to 7 concurrent
micro-ops can be executed per clock), and includes a 128KB 4-way L1
instruction cache, a 64KB 4-way L1 data cache, and a 2MB 16-way L2
cache, which services both cores.

Denver implements an innovative process called Dynamic Code Optimization,
which optimizes frequently used software routines at runtime into dense,
highly tuned microcode-equivalent routines. These are stored in a
dedicated, 128MB main-memory-based optimization cache. After being read
into the instruction cache, the optimized micro-ops are executed,
re-fetched and executed from the instruction cache as long as needed and
capacity allows.

Effectively, this reduces the need to re-optimize the software routines.
Instead of using hardware to extract the instruction-level parallelism
(ILP) inherent in the code, Denver extracts the ILP once via software
techniques, and then executes those routines repeatedly, thus amortizing
the cost of ILP extraction over the many execution instances.

Denver also features new low latency power-state transitions, in addition
to extensive power-gating and dynamic voltage and clock scaling based on
workloads.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch changes the type of the base address parameter in the
ARM device driver APIs to uintptr_t (GIC, CCI, TZC400, PL011). The
uintptr_t type allows coverage of the whole memory space and to
perform arithmetic operations on the addresses. ARM platform code
has also been updated to use uintptr_t as GIC base address in the
configuration.

Fixes ARM-software/tf-issues#214

Change-Id: I1b87daedadcc8b63e8f113477979675e07d788f1

The authentication framework deprecates plat_match_rotpk()
in favour of plat_get_rotpk_info(). This patch removes
plat_match_rotpk() from the platform port.

Change-Id: I2250463923d3ef15496f9c39678b01ee4b33883b

This patch modifies the Trusted Board Boot implementation to use
the new authentication framework, making use of the authentication
module, the cryto module and the image parser module to
authenticate the images in the Chain of Trust.

A new function 'load_auth_image()' has been implemented. When TBB
is enabled, this function will call the authentication module to
authenticate parent images following the CoT up to the root of
trust to finally load and authenticate the requested image.

The platform is responsible for picking up the right makefiles to
build the corresponding cryptographic and image parser libraries.
ARM platforms use the mbedTLS based libraries.

The platform may also specify what key algorithm should be used
to sign the certificates. This is done by declaring the 'KEY_ALG'
variable in the platform makefile. FVP and Juno use ECDSA keys.

On ARM platforms, BL2 and BL1-RW regions have been increased 4KB
each to accommodate the ECDSA code.

REMOVED BUILD OPTIONS:

  * 'AUTH_MOD'

Change-Id: I47d436589fc213a39edf5f5297bbd955f15ae867

This patch adds a CoT based on the Trusted Board Boot Requirements
document*. The CoT consists of an array of authentication image
descriptors indexed by the image identifiers.

A new header file with TBBR image identifiers has been added.
Platforms that use the TBBR (i.e. ARM platforms) may reuse these
definitions as part of their platform porting.

PLATFORM PORT - IMPORTANT:

Default image IDs have been removed from the platform common
definitions file (common_def.h). As a consequence, platforms that
used those common definitons must now either include the IDs
provided by the TBBR header file or define their own IDs.

*The NVCounter authentication method has not been implemented yet.

Change-Id: I7c4d591863ef53bb0cd4ce6c52a60b06fa0102d5

This patch adds the following mbedTLS based libraries:

* Cryptographic library

It is used by the crypto module to verify a digital signature
and a hash. This library relies on mbedTLS to perform the
cryptographic operations. mbedTLS sources must be obtained
separately.

Two key algorithms are currently supported:

    * RSA-2048
    * ECDSA-SECP256R1

The platform is responsible for picking up the required
algorithm by defining the 'MBEDTLS_KEY_ALG' variable in the
platform makefile. Available options are:

    * 'rsa' (for RSA-2048) (default option)
    * 'ecdsa' (for ECDSA-SECP256R1)

Hash algorithm currently supported is SHA-256.

* Image parser library

Used by the image parser module to extract the authentication
parameters stored in X509v3 certificates.

Change-Id: I597c4be3d29287f2f18b82846973afc142ee0bf0

This patch adds the authentication framework that will be used as
the base to implement Trusted Board Boot in the Trusted Firmware.
The framework comprises the following modules:

- Image Parser Module (IPM)

    This module is responsible for interpreting images, check
    their integrity and extract authentication information from
    them during Trusted Board Boot.

    The module currently supports three types of images i.e.
    raw binaries, X509v3 certificates and any type specific to
    a platform. An image parser library must be registered for
    each image type (the only exception is the raw image parser,
    which is included in the main module by default).

    Each parser library (if used) must export a structure in a
    specific linker section which contains function pointers to:

        1. Initialize the library
        2. Check the integrity of the image type supported by
           the library
        3. Extract authentication information from the image

- Cryptographic Module (CM)

    This module is responsible for verifying digital signatures
    and hashes. It relies on an external cryptographic library
    to perform the cryptographic operations.

    To register a cryptographic library, the library must use the
    REGISTER_CRYPTO_LIB macro, passing function pointers to:

        1. Initialize the library
        2. Verify a digital signature
        3. Verify a hash

    Failing to register a cryptographic library will generate
    a build time error.

- Authentication Module (AM)

    This module provides methods to authenticate an image, like
    hash comparison or digital signatures. It uses the image parser
    module to extract authentication parameters, the crypto module
    to perform cryptographic operations and the Chain of Trust to
    authenticate the images.

    The Chain of Trust (CoT) is a data structure that defines the
    dependencies between images and the authentication methods
    that must be followed to authenticate an image.

The Chain of Trust, when added, must provide a header file named
cot_def.h with the following definitions:

- COT_MAX_VERIFIED_PARAMS

    Integer value indicating the maximum number of authentication
    parameters an image can present. This value will be used by the
    authentication module to allocate the memory required to load
    the parameters in the image descriptor.

Change-Id: Ied11bd5cd410e1df8767a1df23bb720ce7e58178

This patch extends the platform port by adding an API that returns
either the Root of Trust public key (ROTPK) or its hash. This is
usually stored in ROM or eFUSE memory. The ROTPK returned must be
encoded in DER format according to the following ASN.1 structure:

    SubjectPublicKeyInfo  ::=  SEQUENCE  {
        algorithm           AlgorithmIdentifier,
        subjectPublicKey    BIT STRING
    }

In case the platform returns a hash of the key:

    DigestInfo  ::= SEQUENCE {
        digestAlgorithm     AlgorithmIdentifier,
        keyDigest           OCTET STRING
    }

An implementation for ARM development platforms is provided in this
patch. When TBB is enabled, the ROTPK hash location must be specified
using the build option 'ARM_ROTPK_LOCATION'. Available options are:

    - 'regs' : return the ROTPK hash stored in the Trusted
      root-key storage registers.

    - 'devel_rsa' : return a ROTPK hash embedded in the BL1 and
      BL2 binaries. This hash has been obtained from the development
      RSA public key located in 'plat/arm/board/common/rotpk'.

On FVP, the number of MMU tables has been increased to map and
access the ROTPK registers.

A new file 'board_common.mk' has been added to improve code sharing
in the ARM develelopment platforms.

Change-Id: Ib25862e5507d1438da10773e62bd338da8f360bf

The Trusted firmware code identifies BL images by name. The platform
port defines a name for each image e.g. the IO framework uses this
mechanism in the platform function plat_get_image_source(). For
a given image name, it returns the handle to the image file which
involves comparing images names. In addition, if the image is
packaged in a FIP, a name comparison is required to find the UUID
for the image. This method is not optimal.

This patch changes the interface between the generic and platform
code with regard to identifying images. The platform port must now
allocate a unique number (ID) for every image. The generic code will
use the image ID instead of the name to access its attributes.

As a result, the plat_get_image_source() function now takes an image
ID as an input parameter. The organisation of data structures within
the IO framework has been rationalised to use an image ID as an index
into an array which contains attributes of the image such as UUID and
name. This prevents the name comparisons.

A new type 'io_uuid_spec_t' has been introduced in the IO framework
to specify images identified by UUID (i.e. when the image is contained
in a FIP file). There is no longer need to maintain a look-up table
[iname_name --> uuid] in the io_fip driver code.

Because image names are no longer mandatory in the platform port, the
debug messages in the generic code will show the image identifier
instead of the file name. The platforms that support semihosting to
load images (i.e. FVP) must provide the file names as definitions
private to the platform.

The ARM platform ports and documentation have been updated accordingly.
All ARM platforms reuse the image IDs defined in the platform common
code. These IDs will be used to access other attributes of an image in
subsequent patches.

IMPORTANT: applying this patch breaks compatibility for platforms that
use TF BL1 or BL2 images or the image loading code. The platform port
must be updated to match the new interface.

Change-Id: I9c1b04cb1a0684c6ee65dee66146dd6731751ea5

This patch fixes the build time condition deciding whether the
read-write data should be relocated from ROM to RAM. It was incorrectly
using __DATA_ROM_START__, which is a linker symbol and not a compiler
build flag. As a result, the relocation code was always compiled out.

This bug has been introduced by the following patch:
"Rationalize reset handling code"

Change-Id: I1c8d49de32f791551ab4ac832bd45101d6934045

This patch adds support for SYSTEM_SUSPEND API as mentioned in the PSCI 1.0
specification. This API, on being invoked on the last running core on a
supported platform, will put the system into a low power mode with memory
retention.

The psci_afflvl_suspend() internal API has been reused as most of the actions
to suspend a system are the same as invoking the PSCI CPU_SUSPEND API with the
target affinity level as 'system'. This API needs the 'power state' parameter
for the target low power state. This parameter is not passed by the caller of
the SYSTEM_SUSPEND API. Hence, the platform needs to implement the
get_sys_suspend_power_state() platform function to provide this information.
Also, the platform also needs to add support for suspending the system to the
existing 'plat_pm_ops' functions: affinst_suspend() and
affinst_suspend_finish().

Change-Id: Ib6bf10809cb4e9b92f463755608889aedd83cef5

Add SP804 delay timer support to the FVP BSP.

This commit simply provides the 3 constants needed by the SP804
delay timer driver and calls sp804_timer_init() in
bl2_platform_setup(). The BSP does not currently use the delay
timer functions.

Note that the FVP SP804 is a normal world accessible peripheral
and should not be used by the secure world after transition
to the normal world.

Change-Id: I5f91d2ac9eb336fd81943b3bb388860dfb5f2b39
Co-authored-by: Dan Handley <dan.handley@arm.com>

Add a delay timer driver for the ARM SP804 dual timer.

This driver only uses the first timer, called timer 1 in the
SP804 Technical Reference Manual (ARM DDI 0271D).

To use this driver, the BSP must provide three constants:

*   The base address of the SP804 dual timer
*   The clock multiplier
*   The clock divider

The BSP is responsible for calling sp804_timer_init(). The SP804
driver instantiates a constant timer_ops_t and calls the generic
timer_init().

Change-Id: I49ba0a52bdf6072f403d1d0a20e305151d4bc086
Co-authored-by: Dan Handley <dan.handley@arm.com>

The API is simple. The BSP or specific timer driver creates an
instance of timer_ops_t, fills in the timer specific data, then calls
timer_init(). The timer specific data includes a function pointer
to return the timer value and a clock multiplier/divider. The ratio
of the multiplier and the divider is the clock frequency in MHz.

After that, mdelay() or udelay() can be called to delay execution for
the specified time (milliseconds or microseconds, respectively).

Change-Id: Icf8a295e1d25874f789bf28b7412156329dc975c
Co-authored-by: Dan Handley <dan.handley@arm.com>

For CSS based platforms, the constants MHU_SECURE_BASE and
MHU_SECURE_SIZE used to define the extents of the Trusted Mailboxes.
As such, they were misnamed because the mailboxes are completely
unrelated to the MHU hardware.

This patch removes the MHU_SECURE_BASE and MHU_SECURE_SIZE #defines.
The address of the Trusted Mailboxes is now relative to the base of
the Trusted SRAM.

This patch also introduces a new constant, SCP_COM_SHARED_MEM_BASE,
which is the address of the first memory region used for communication
between AP and SCP. This is used by the BOM and SCPI protocols.

Change-Id: Ib200f057b19816bf05e834d111271c3ea777291f

Add a comment explaining what the SCP boot configuration information
is on CSS based platforms like Juno. Also express its address
relatively to the base of the Trusted SRAM rather than hard-coding it.

Change-Id: I82cf708a284c8b8212933074ea8c37bdf48b403b

The attempt to run the CPU reset code as soon as possible after reset
results in highly complex conditional code relating to the
RESET_TO_BL31 option.

This patch relaxes this requirement a little. In the BL1, BL3-1 and
PSCI entrypoints code, the sequence of operations is now as follows:
 1) Detect whether it is a cold or warm boot;
 2) For cold boot, detect whether it is the primary or a secondary
    CPU. This is needed to handle multiple CPUs entering cold reset
    simultaneously;
 3) Run the CPU init code.

This patch also abstracts the EL3 registers initialisation done by
the BL1, BL3-1 and PSCI entrypoints into common code.

This improves code re-use and consolidates the code flows for
different types of systems.

NOTE: THE FUNCTION plat_secondary_cold_boot() IS NOW EXPECTED TO
NEVER RETURN. THIS PATCH FORCES PLATFORM PORTS THAT RELIED ON THE
FORMER RETRY LOOP AT THE CALL SITE TO MODIFY THEIR IMPLEMENTATION.
OTHERWISE, SECONDARY CPUS WILL PANIC.

Change-Id: If5ecd74d75bee700b1bd718d23d7556b8f863546

This patch removes the FIRST_RESET_HANDLER_CALL build flag and its
use in ARM development platforms. If a different reset handling
behavior is required between the first and subsequent invocations
of the reset handling code, this should be detected at runtime.

On Juno, the platform reset handler is now always compiled in.
This means it is now executed twice on the cold boot path, first in
BL1 then in BL3-1, and it has the same behavior in both cases. It is
also executed twice on the warm boot path, first in BL1 then in the
PSCI entrypoint code.

Also update the documentation to reflect this change.

NOTE: THIS PATCH MAY FORCE PLATFORM PORTS THAT USE THE
FIRST_RESET_HANDLER_CALL BUILD OPTION TO FIX THEIR RESET HANDLER.

Change-Id: Ie5c17dbbd0932f5fa3b446efc6e590798a5beae2

This patch adds driver for the 16550 UART interface. The driver is exposed
as a console, which platforms can use to dump their boot/crash logs.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch fixes the incorrect bit width used to extract the primary
cpu id from `ap_data` exported by scp at SCP_BOOT_CFG_ADDR in
platform_is_primary_cpu().

Change-Id: I14abb361685f31164ecce0755fc1a145903b27aa

The ARM GIC driver treats the entire contents of the GICC_HPPIR as the interrupt
ID instead of just bits[9:0]. This could result in an SGI being treated as a
Group 1 interrupt on a GICv2 system.

This patch introduces a mask to retrieve only the ID from a read of GICC_HPPIR,
GICC_IAR and similar registers. The value read from these registers is masked
with this constant prior to use as an interrupt ID.

Fixes ARM-software/tf-issues#306

Change-Id: Ie3885157de33b71df9781a41f6ef015a30c4608d

Major update to the FVP platform port to use the common platform code
in (include/)plat/arm/* and (include/)plat/common/*. This mainly
consists of removing duplicated code but also introduces some small
behavioural changes where there was unnecessary variation between the
FVP and Juno ports. See earlier commit titled `Add common ARM and CSS
platform code` for details.

Also add support for Foundation FVP version 9.1 during FVP config
setup to prevent a warning being emitted in the console.

Change-Id: I254ca854987642ce09d1b924c9fd410a6e13e3bc

This major change pulls out the common functionality from the
FVP and Juno platform ports into the following categories:

*   (include/)plat/common. Common platform porting functionality that
typically may be used by all platforms.

*   (include/)plat/arm/common. Common platform porting functionality
that may be used by all ARM standard platforms. This includes all
ARM development platforms like FVP and Juno but may also include
non-ARM-owned platforms.

*   (include/)plat/arm/board/common. Common platform porting
functionality for ARM development platforms at the board
(off SoC) level.

*   (include/)plat/arm/css/common. Common platform porting
functionality at the ARM Compute SubSystem (CSS) level. Juno
is an example of a CSS-based platform.

*   (include/)plat/arm/soc/common. Common platform porting
functionality at the ARM SoC level, which is not already defined
at the ARM CSS level.

No guarantees are made about the backward compatibility of
functionality provided in (include/)plat/arm.

Also remove any unnecessary variation between the ARM development
platform ports, including:

*   Unify the way BL2 passes `bl31_params_t` to BL3-1. Use the
Juno implementation, which copies the information from BL2 memory
instead of expecting it to persist in shared memory.

*   Unify the TZC configuration. There is no need to add a region
for SCP in Juno; it's enough to simply not allow any access to
this reserved region. Also set region 0 to provide no access by
default instead of assuming this is the case.

*   Unify the number of memory map regions required for ARM
development platforms, although the actual ranges mapped for each
platform may be different. For the FVP port, this reduces the
mapped peripheral address space.

These latter changes will only be observed when the platform ports
are migrated to use the new common platform code in subsequent
patches.

Change-Id: Id9c269dd3dc6e74533d0e5116fdd826d53946dc8

Add extern declarations of linker symbols to bl_common.h. These are
used by platform ports to determine the memory layout of BL images.
Adding the declarations to this file facilitates removal of these
declarations from the platform porting source files in subsequent
patches.

Also remove the linker symbol declarations from common TSP source
code.

Change-Id: I8ed0426bc815317c4536b588e4e78bc15b4fe91c

Some assembly files containing macros are included like header files
into other assembly files. This will cause assembler errors if they
are included multiple times.

Add header guards to assembly macro files to avoid assembler errors.

Change-Id: Ia632e767ed7df7bf507b294982b8d730a6f8fe69

The required platform constant PLATFORM_CACHE_LINE_SIZE is
unnecessary since CACHE_WRITEBACK_GRANULE effectively provides the
same information. CACHE_WRITEBACK_GRANULE is preferred since this
is an architecturally defined term and allows comparison with the
corresponding hardware register value.

Replace all usage of PLATFORM_CACHE_LINE_SIZE with
CACHE_WRITEBACK_GRANULE.

Also, add a runtime assert in BL1 to check that the provided
CACHE_WRITEBACK_GRANULE matches the value provided in CTR_EL0.

Change-Id: If87286be78068424217b9f3689be358356500dcd

Region 0 is special in TZC-400. It is possible to set the access
permissions for this but not the address range or filters to which
the permissions apply. Add a function for setting the region 0
access permissions.

Also add some VERBOSE logging and allow assembly files to include
the TZC header.

Change-Id: I4389261ba10a6e5e2e43ee93d55318dc507b6648

This patch removes the need for a shared buffer between the EL3 and S-EL1
levels. We now use the CPU registers, x0-x7, while passing data between
the two levels. Since TLK is a 32-bit Trusted OS, tlkd has to unpack the
arguments in the x0-x7 registers. TLK in turn gets these values via r0-r7.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

In order for the symbol table in the ELF file to contain the size of
functions written in assembly, it is necessary to report it to the
assembler using the .size directive.

To fulfil the above requirements, this patch introduces an 'endfunc'
macro which contains the .endfunc and .size directives. It also adds
a .func directive to the 'func' assembler macro.

The .func/.endfunc have been used so the assembler can fail if
endfunc is omitted.

Fixes ARM-Software/tf-issues#295

Change-Id: If8cb331b03d7f38fe7e3694d4de26f1075b278fc
Signed-off-by: Kévin Petit <kevin.petit@arm.com>

This patch adds support to open/close secure sessions with Trusted
Apps and later send commands/events. Modify TLK_NUM_FID to indicate
the total number of FIDs available to the NS world.

Change-Id: I3f1153dfa5510bd44fc25f1fee85cae475b1abf1
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch allows servicing of the non-secure world IRQs when the
CPU is in the secure world. Once the interrupt is handled, the
non-secure world issues the Resume FID to allow the secure payload
complete the preempted standard FID.

Change-Id: Ia52c41adf45014ab51d8447bed6605ca2f935587
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds functionality to translate virtual addresses from
secure or non-secure worlds. This functionality helps Trusted Apps
to share virtual addresses directly and allows the NS world to
pass virtual addresses to TLK directly.

Change-Id: I77b0892963e0e839c448b5d0532920fb7e54dc8e
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch registers NS memory buffer with the secure payload using
two different functions IDs - REGISTER_LOGBUF, REGISTER_REQBUF.

a. The SP uses the log-buffer to store its activity logs, in a
pre-decided format. This helps in debugging secure payload's issues.
b. The SP uses the req-buffer to get the parameters required by
sessions with Trusted Applications.

Change-Id: I6b0247cf7790524132ee0da24f1f35b1fccec5d5
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

TLK Dispatcher (tlkd) is based on the tspd and is the glue required
to run TLK as a Secure Payload with the Trusted Firmware.

Change-Id: I69e573d26d52342eb049feef773dd7d2a506f4ab
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch removes the `owner` field in bakery_lock_t structure which
is the data structure used in the bakery lock implementation that uses
coherent memory. The assertions to protect against recursive lock
acquisition were based on the 'owner' field. They are now done based
on the bakery lock ticket number. These assertions are also added
to the bakery lock implementation that uses normal memory as well.

Change-Id: If4850a00dffd3977e218c0f0a8d145808f36b470

This patch optimizes the data structure used with the bakery lock
implementation for coherent memory to save memory and minimize memory
accesses. These optimizations were already part of the bakery lock
implementation for normal memory and this patch now implements
it for the coherent memory implementation as well. Also
included in the patch is a cleanup to use the do-while loop while
waiting for other contenders to finish choosing their tickets.

Change-Id: Iedb305473133dc8f12126726d8329b67888b70f1

This patch adds support for ARM Cortex-A72 processor in the CPU
specific framework.

Change-Id: I5986855fc1b875aadf3eba8c36e989d8a05e5175