Import firmware from armbian/build

brcm/brcmfmac4330-sdio.txt

+# bcm94330wlsdgb.txt
+manfid=0x2d0
+prodid=0x0552
+vendid=0x14e4
+devid=0x4360
+boardtype=0x0552
+boardrev=0x11
+# this design has 2.4GHz SP3T switch
+boardflags=0x00080200
+nocrc=1
+xtalfreq=37400
+boardnum=22
+macaddr=00:90:4c:c5:12:38
+ag0=255
+aa2g=1
+ccode=CN
+pa0b0=0x14d0
+pa0b1=0xfd98
+pa0b2=0xff78
+rssismf2g=0xa
+rssismc2g=0x3
+rssisav2g=0x7
+maxp2ga0=0x50
+sromrev=3
+il0macaddr=00:90:4c:c5:12:38
+wl0id=0x431b
+cckPwrOffset=5
+ofdm2gpo=0x66666666
+mcs2gpo0=0x6666
+mcs2gpo1=0x6666
+swctrlmap_2g=0x04040404,0x02020202,0x02020404,0x10202,0x1ff
+swctrlmap_5g=0x00100010,0x00280020,0x00200010,0x14202,0x2f8
+rfreg033=0x19
+rfreg033_cck=0x1f
+dacrate2g=160
+txalpfbyp2g=1
+bphyscale=17
+cckPwrIdxCorr=-15
+pacalidx2g=45
+txgaintbl=1

brcm/brcmfmac43362-sdio.txt

+#AP6210_NVRAM_V1.2_03192013
+manfid=0x2d0
+prodid=0x492
+vendid=0x14e4
+devid=0x4343
+boardtype=0x0598
+
+# Board Revision is P307, same nvram file can be used for P304, P305, P306 and P307 as the tssi pa params used are same
+#Please force the automatic RX PER data to the respective board directory if not using P307 board, for e.g. for P305 boards force the data into the following directory /projects/BCM43362/a1_labdata/boardtests/results/sdg_rev0305
+boardrev=0x1307
+boardnum=777
+xtalfreq=26000
+boardflags=0x80201
+boardflags2=0x80
+sromrev=3
+wl0id=0x431b
+macaddr=00:90:4c:07:71:12
+aa2g=1
+ag0=2
+maxp2ga0=74
+cck2gpo=0x2222
+ofdm2gpo=0x44444444
+mcs2gpo0=0x6666
+mcs2gpo1=0x6666
+pa0maxpwr=56
+
+#P207 PA params
+#pa0b0=5447
+#pa0b1=-658
+#pa0b2=-175<div></div>
+
+#Same PA params for P304,P305, P306, P307
+
+pa0b0=5447
+pa0b1=-607
+pa0b2=-160
+pa0itssit=62
+pa1itssit=62
+
+
+cckPwrOffset=5
+ccode=0
+rssismf2g=0xa
+rssismc2g=0x3
+rssisav2g=0x7
+triso2g=0
+noise_cal_enable_2g=0
+noise_cal_po_2g=0
+swctrlmap_2g=0x04040404,0x02020202,0x02020202,0x010101,0x1ff
+temp_add=29767
+temp_mult=425
+
+btc_flags=0x6
+btc_params0=5000
+btc_params1=1000
+btc_params6=63
+

brcm/brcmfmac43430-sdio.txt

+#AP6212_NVRAM_V1.0_20140603
+# 2.4 GHz, 20 MHz BW mode
+
+# The following parameter values are just placeholders, need to be updated.
+manfid=0x2d0
+prodid=0x0726
+vendid=0x14e4
+devid=0x43e2
+boardtype=0x0726
+boardrev=0x1101
+boardnum=22
+macaddr=00:90:4c:c5:12:38
+sromrev=11
+boardflags=0x00404201
+xtalfreq=26000
+nocrc=1
+ag0=255
+aa2g=1
+ccode=ALL
+
+pa0itssit=0x20
+extpagain2g=0
+
+#PA parameters for 2.4GHz, measured at CHIP OUTPUT
+pa2ga0=-168,7161,-820
+AvVmid_c0=0x0,0xc8
+cckpwroffset0=5
+
+# PPR params
+maxp2ga0=90
+txpwrbckof=6
+cckbw202gpo=0x5555
+legofdmbw202gpo=0x77777777
+mcsbw202gpo=0xaaaaaaaa
+
+# OFDM IIR :
+ofdmdigfilttype=7
+# PAPD mode:
+papdmode=2
+
+il0macaddr=00:90:4c:c5:12:38
+wl0id=0x431b
+
+#OOB parameters
+hostwake=0x40
+hostrdy=0x41
+usbrdy=0x03
+usbrdydelay=100
+deadman_to=0xffffffff
+# muxenab: 0x1 for UART enable, 0x10 for Host awake
+muxenab=0x10
+# CLDO PWM voltage settings - 0x4 - 1.1 volt
+#cldo_pwm=0x4
+

brcm/config.txt

+PM=0
+nv_by_chip=1 \
+43362 1 nvram_ap6210.txt
+43430 0 nvram_ap6212.txt