rockchip: really use base+size for secure ddr regions

The calls to secure ddr regions on rk3288 and rk3399 use parameters of
base and size - as it custom for specifying memory regions, but the
functions themself expect start and endpoints of the area.

This only works by chance for the TZRAM, as it starts a 0x0 and therefore
its end location is the same as its size.

To not fall into a trap later on adapt the functions to really take
base+size parameters.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Change-Id: Idb9fab38aa081f3335a4eca971e7b7f6757fbbab

plat/rockchip/rk3288/drivers/secure/secure.c

 /*
- * Copyright (c) 2016, ARM Limited and Contributors. All rights reserved.
+ * Copyright (c) 2016-2019, ARM Limited and Contributors. All rights reserved.
  *
  * SPDX-License-Identifier: BSD-3-Clause
  */
@@ -38,15 +38,18 @@ static void sgrf_ddr_rgn_global_bypass(uint32_t bypass)
  * SGRF_SOC_CON21 - end address of the RGN_7 + RGN_X control
  *
  * @rgn - the DDR regions 0 ~ 7 which are can be configured.
- * The @st and @ed indicate the start and end addresses for which to set
- * the security, and the unit is byte. When the st_mb == 0, ed_mb == 0, the
+ * @st - start address to set as secure
+ * @sz - length of area to set as secure
+ * The @st_mb and @ed_mb indicate the start and end addresses for which to set
+ * the security, and the unit is megabyte. When the st_mb == 0, ed_mb == 0, the
  * address range 0x0 ~ 0xfffff is secure.
  *
  * For example, if we would like to set the range [0, 32MB) is security via
  * DDR_RGN0, then rgn == 0, st_mb == 0, ed_mb == 31.
  */
-static void sgrf_ddr_rgn_config(uint32_t rgn, uintptr_t st, uintptr_t ed)
+static void sgrf_ddr_rgn_config(uint32_t rgn, uintptr_t st, size_t sz)
 {
+	uintptr_t ed = st + sz;
 	uintptr_t st_mb, ed_mb;
 
 	assert(rgn <= 7);

plat/rockchip/rk3399/drivers/secure/secure.c

 /*
- * Copyright (c) 2016, ARM Limited and Contributors. All rights reserved.
+ * Copyright (c) 2016-2019, ARM Limited and Contributors. All rights reserved.
  *
  * SPDX-License-Identifier: BSD-3-Clause
  */
@@ -45,6 +45,8 @@ static void sgrf_ddr_rgn_global_bypass(uint32_t bypass)
  *                bypass, 1: enable bypass
  *
  * @rgn - the DDR regions 0 ~ 7 which are can be configured.
+ * @st - start address to set as secure
+ * @sz - length of area to set as secure
  * The @st_mb and @ed_mb indicate the start and end addresses for which to set
  * the security, and the unit is megabyte. When the st_mb == 0, ed_mb == 0, the
  * address range 0x0 ~ 0xfffff is secure.
@@ -53,8 +55,9 @@ static void sgrf_ddr_rgn_global_bypass(uint32_t bypass)
  * DDR_RGN0, then rgn == 0, st_mb == 0, ed_mb == 31.
  */
 static void sgrf_ddr_rgn_config(uint32_t rgn,
-				uintptr_t st, uintptr_t ed)
+				uintptr_t st, size_t sz)
 {
+	uintptr_t ed = st + sz;
 	uintptr_t st_mb, ed_mb;
 
 	assert(rgn <= 7);