GitLab

We make sure the resuming of gic need to be enabled.
Otherwise, The resume will hit the below panic.
...
[   24.230541] CPU0: update max cpu_capacity 451
[   24.236029] CPU5: update max cpu_capacity 1024
[   24.236046] CPU4: shutdown
[   24.243205] psci: CPU4 killed.
[   24.258730] CPU5: shutdown
[   24.261472] psci: CPU5 killed.
[   24.270417] GIC: unable to set SRE (disabled at EL2), panic ahead
[   24.270417] cat[7801]: undefined instruction: pc=ffffffc0004e65d0
[   24.270417] Code: b0003940 91274400 97f871af d2801e00 (d5184600)
[   24.270417] Internal error: Oops - undefined instruction: 0 [#1] PREEMPT

Change-Id: Ie9542c8d5768ba0accfa073453da8bfe06d4f921

Set apio for rk3399

Flush `psci_plat_pm_ops` after initialization

For save power cosumption, if gpio power supply shut down, we need to
set gpio2 ~ gpio4 to input and HiZ status when suspend, and recovery
they status when rusume. we do it base on apio pass from loader.

Change-Id: I59fd2395e5e37e63425472a39f519822c9197e4c

some specific board need to disable/enable specific gpio when
suspend/resume, so we add this function, bootloader can pass the
specific gpio, and we can handle these gpios in bl31 suspend/resuem
function.

Change-Id: I373b03ef9202ee4a05a2b9caacdfa01b47ee2177

We may need gpio pull mode later, so add this function.
Besides fix a set pull mode bug, and save gpio clock gate,
when operate the gpio, we will enable gpio clock, when
finish gpio operate, restore gpio clock gate status.

Change-Id: Ia1d602804f571a17f5ddc499908663b968b02974

The `psci_plat_pm_ops` global pointer is initialized during cold boot by the
primary CPU and will be accessed by the secondary CPUs before enabling data
cache during warm boot. This patch adds a missing data cache flush of
`psci_plat_psci_ops` after initialization during psci_setup() so that
secondaries can see the updated `psci_plat_psci_ops` pointer.

Fixes ARM-software/tf-issues#424

Change-Id: Id4554800b5646302b944115a33be69507d53cedb

rockchip: fix the scu idle for rk3399

As rk3399 reported the d8/octane scores drop 10% with cpu idle.
The root cause is thc cpu cluster enter the slow mode.
We don't need switch the clock to 24MHz if cpu cluster enter the
retention mode. In order to improve performance, it just needs for
cluster enter powering off mode.

Also, we shouldn't do anything for hlvl if the system is off.

Change-Id: I2a02962a01343abd0cba47ed63192c1cdf88b119

Fixes for AArch32 port of TF

This patch fixes a bug in context management library when writing
SCTLR register during context initialization. The write happened
prior to initialization of the register context pointer. This
resulted in the compiler optimizing the write sequence from the
final binary and hence SCTLR remains uninitialized when
entering normal world. The bug is fixed by doing the
initialization of the register context pointer earlier in the
sequence.

Change-Id: Ic7465593a74534046b79f40446ffa1165c52ed76

This patch resolves a build error in Trusted Firmware when `ARCH=aarch32`
and LOG_LEVEL >= 50.

Change-Id: I62a23ded4a25304533cdcc5ff11442aee041709b

Remove looping around `plat_report_exception`

Automatically select initial xlation lookup level

Move pmf headers to include/lib/pmf and add assembler helper

fiptool: Fix typo in create and update usage functions

Fixes suspend/resume bugs

Given the service name and timestamp id, this assembler macro
calculates the offset into a memory region where the per-cpu timestamp
value is located.

Change-Id: I47f6dfa2a17be182675e2ca0489d6eed42433209

More headers will be needed soon so better to move these to their own
directory to avoid cluttering include/lib.

Change-Id: I6a72dc5b602d6f51954cf60aadd1beb52a268670

rockchip: add dram driver for rk3399

It should be 'fiptool' instead of 'fiptfool'.

Change-Id: I84ce1b6aaae5b8b33e5781bfe4f9e9cf462edb03

For the PMU design, we don't expect to get the interrupts before enter
the power mode. Since that will cause the confusion for the state
machine in the power mode.

Change-Id: Id8dee79ae617a66271b5caf92caf35f520f45099

Change-Id: I986d64df9dc62354d50ccea0468b90f090a44160
Signed-off-by: Caesar Wang <wxt@rock-chips.com>

If we don't enable the Schmitt trigger on the 32 kHz clock then systems
won't always resume from suspend properly.  Presumably anything else in
the system that relies on the 32 kHz clock also will have problems
without the Schmitt trigger enabled.

Enable it always since having the 32 kHz clock on GPIO0_A0 isn't
exactly an optional feature, so all boards using rk3399 will need this.

Change-Id: Idc18c6cd1adc5be5f60efd9cb805d83d5cd40129

add auto_pd_dis_freq parameter, we can pass a frequency from kernel
to disable or enable ddr auto power down function.

Change-Id: Ie30914701336c59047c380381c6b75dd76a89562

add dram driver, and kernel can through sip function talk to bl31 to
do ddr frequency scaling. and ddr auto powerdown.

Change-Id: I0d0f2869aed95e336c6e23ba96a9310985c84840

In a previous change we mistakenly thought that PMU_24M_EN_CFG directly
controlled whether the PMU counts ran off the 32k vs. 24M clock.
Apparently that's not true.  Real logic is now documented in code.

Also in the previous change we mistaknely though that PMU_24M_EN_CFG was
normally supposed to be 1 and we should "restore" it at resume time.
This is a terrible idea and made the system totally unreliable after
resume.  Apparently PMU_24M_EN_CFG should always be 0 with all the
current code and settings.

Let's fix the above two problems.  While we're changing all of this,
let's also:

1. Init at boot time.  Many of these counts are used when the system is
   running normally.  We want the behavior at boot to match the behavior
   after suspend/resume.

2. Init CPU counts to be 1 us.  Although old code was trying to set this
   to 1 ms (1000x slower) at suspend/resume time, we've been testing the
   kernel with 1 us for a long time now.  That's because the kernel (at
   boot time) set these values to 24.  Let's keep at 24 until we know
   that's wrong.

3. Init GPU counts to be 1 us.  Old code wasn't touching the GPU, but as
   documented in comments it makes sense to init here.  Do it.

4. Document the crap out of this code, since the SoC's behavior is
   confusing and poorly documented in the TRM.

5. Increase some stabilization times to 30 ms (from 3 ms).  It's unclear
   that a full 30 ms is needed, but let's be safe for now.

This also inits the counts for the GPU.

(Thanks to Doug's patch that come from https://crosreview.com/372381)

Change-Id: Id1bc159a5a99916aeab043895e5c4585c4adab22

Instead of hardcoding a level 1 table as the base translation level
table, let the code decide which level is the most appropriate given
the virtual address space size.

As the table granularity is 4 KB, this allows the code to select
level 0, 1 or 2 as base level for AArch64. This way, instead of
limiting the virtual address space width to 39-31 bits, widths of
48-25 bit can be used.

For AArch32, this change allows the code to select level 1 or 2
as the base translation level table and use virtual address space
width of 32-25 bits.

Also removed some unused definitions related to translation tables.

Fixes ARM-software/tf-issues#362

Change-Id: Ie3bb5d6d1a4730a26700b09827c79f37ca3cdb65

This patch removes the tight loop that calls `plat_report_exception`
in unhandled exceptions in AArch64 state.
The new behaviour is to call the `plat_report_exception` only
once followed by call to `plat_panic_handler`.
This allows platforms to take platform-specific action when
there is an unhandled exception, instead of always spinning
in a tight loop.

Note: This is a subtle break in behaviour for platforms that
      expect `plat_report_exception` to be continuously executed
      when there is an unhandled exception.

Change-Id: Ie2453804b9b7caf9b010ee73e1a90eeb8384e4e8

Add WFI in platform's unexpected error handlers

This patch adds a WFI instruction in the default implementations of
plat_error_handler() and plat_panic_handler(). This potentially reduces
power consumption by allowing the hardware to enter a low-power state.
The same change has been made to the FVP and Juno platform ports.

Change-Id: Ia4e6e1e5bf1ed42efbba7d0ebbad7be8d5f9f173

Remove dcache invalidation after image authentication

Introduce AArch32 support for PSCI library

At the end of successful image authentication in load_auth_image(),
the data cache for the virtual address range corresponding to the
image is invalidated (by a call to inv_dcache_range()). The intent
seems to be to ensure the data caches do not contain any sensitive
data used during authentication, which subsequent code can read.
However, this same address range is already flushed (cleaned and
invalidated by a call to flush_dcache_range()) at the end of
load_image(), and the subsequent invalidate has no functional
effect.

This patch removes the redundant call to inv_dcache_range(). It
also moves the flush_dcache_range() call from the end of load_image()
to the end of load_auth_image(), so the image data will remain in
the caches during authentication, improving performance.

This also improves the comments that explain the rationale for
calling flush_dcache_range() after image loading/authentication.

Change-Id: I14f17ad2935075ef6f3d1327361c5088bfb2d284

Move up to Base FVP version 7.6

fiptool: Suppress verbose messages during normal build

gicv3: disable Group1 NonSecure interrupts during core powerdown

emmc: support CMD23

This patch updates the User Guide to move up from version 7.2 to 7.6
of the Base FVP.

Change-Id: I792b2250deb4836266e14b40992ae59a5ab5f729

The output is shown only when built with V=1.

Change-Id: I17fef10df6f127f07956a78b478ff3cadba4bd61