GitLab

There is really no reason to use and pass around a struct when its only
member is the (fixed) base address.

Remove the struct and just use the base address on its own inside the
GPIO driver. Then set the base address automatically.

This simplifies GPIO setup for users, which now don't need to deal with
zeroing a struct and setting the base address anymore.

Change-Id: I3060f7859e3f8ef9a24cc8fb38307b5da943f127
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

At the moment the UART input clock rate is hard coded at compile time.
This works as long as the GPU firmware always sets up the same rate,
which does not seem to be true for the Raspberry Pi 4.

In preparation for being able to change this at runtime, add a base
clock parameter to the console setup function. This is still hardcoded
for the Raspberry Pi 3.

Change-Id: I398bc2f1e9b46f7af9a84cb0b33cbe8e78f2d900
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

With the incoming support for the Raspberry Pi 4 boards, one directory
to serve both versions will not end up well.

Create an additional layer by inserting a "rpi" directory betweeen /plat
and rpi3, so that we can more easily share or separate files between the
two later.

Change-Id: I75adbb054fe7902f34db0fd5e579a55612dd8a5f
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

This commit improves the SDHost driver for RPi3 as following:
 * Unblock MMC_CMD(17). Using MMC_CMD(17) is more efficient on
   block reading.
 * In some low probability that SEND_OP_COND might results CRC7
   error. We can consider that the command runs correctly. We don't
   need to retry this command so removing the code for retry.
 * Using MMC_BUS_WIDTH_1 as MMC default value to improve the stability.
 * Increase the clock to 50Mhz in data mode to speed up the io.
 * Change the pull resistors configuration to gain more stability.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>

This patch inits SDHost in BL2 earlysetup. BL2 can start operating mmc
commands to read/write MMC raw blocks.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>

This patch inits the GPIO in BL2 earlysetup. So BL2 can start operating
GPIO pins.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}

The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).

For example, this patch had to be created because two headers were
called the same way: e0ea0928 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3 ("drivers: add tzc380 support").

This problem was introduced in commit 4ecca339

 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.

Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.

Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: If53b5b2430a06ce8cf6e7948765b560b37afc335
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Support for loading optee images as BL32 secure payload.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>

Switch to the new console APIs enabled by setting MULTI_CONSOLE_API=1.

The crash console doesn't use this API, it uses internally the core
functions of the 16550 console.

`bl31_plat_runtime_setup` is no longer needed. When this platform port
was introduced, that function used to disable the console. It was needed
to override that behaviour. The new behaviour is to switch to the
runtime console. The console is registered for all scopes (boot, crash
and runtime) in `rpi3_console_init` so it is not needed to override the
default behaviour anymore.

Update documentation.

Change-Id: If2ee8f91044216183b7ef142e5c05ad6220ae92f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Ensure (where possible) that switch statements in plat comply with MISRA
rules 16.1 - 16.7.

Change-Id: Ie4a7d2fd10f6141c0cfb89317ea28a755391622f
Signed-off-by: Jonathan Wright <jonathan.wright@arm.com>

This port can be compiled to boot an AArch64 or AArch32 payload with the
build option `RPI3_BL33_AARCH32`.

Note: This is not a secure port of the Trusted Firmware. This port is
only meant to be a reference implementation to experiment with an
inexpensive board in real hardware.

Change-Id: Ide58114299289bf765ef1366199eb05c46f81903
Co-authored-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>