GitLab

Even though we initialise the platform part and the I2C controller
itself at boot time, we actually only access the bus on power down.
Meanwhile a rich OS might have configured the I2C pins differently or
even disabled the controller.
So repeat the platform setup and controller initialisation just before
we actually access the bus to power off the system. This is safe,
because at this point the rich OS should no longer be running.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Drop the unnecessary check for the I2C pins being already configured as
I2C pins (we actually don't care).
Also avoid resetting *every* peripheral that is covered by the PRCM reset
controller, instead just clear the one line connected to the I2C controller.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

This patch fixes an array overrun in CSS scmi driver if the
system power domain level is less than 2. This was reported from
https://scan.coverity.com/projects/arm-software-arm-trusted-firmware



CID 308492

Change-Id: I3a59c700490816718d20c71141281f19b2b7e7f7
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch adds experimental support for TBB to the HiKey960 board. To
build and test with TBB modify the uefi-tools project platforms.config

+ATF_BUILDFLAGS=TRUSTED_BOARD_BOOT=1 GENERATE_COT=1 SAVE_KEYS=1 \
  MBEDTLS_DIR=./mbedtls
Signed-off-by: Teddy Reed <teddy@casualhacking.io>

The AXP805 PMIC used with H6 is capable of shutting down the system.

Add support for using it to shut down the system power.

The original placeholder power off code is moved to A64 code, as it's
still TODO to implement PMIC operations for A64.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

The OTT reference design of Allwinner H6 SoC uses an X-Powers AXP805
PMIC.

Add initial code for it.

Currently it's only detected.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

As the ATF may need to do some power initialization on Allwinner
platform with AXP PMICs, call the PMIC setup code in BL31.

Stub of PMIC setup code is added, to prevent undefined reference.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

The patch 7b56928a

 unified the FWU mechanism on FVP and Juno
platforms due to issues with MCC firmware not preserving the
NVFLAGS. With MCCv150 firmware, this issue is resolved. Also
writing to the NOR flash while executing from the same flash
in Bypass mode had some stability issues. Hence, since the
MCC firmware issue is resolved, this patch reverts to the
NVFLAGS mechanism to detect FWU. Also, with the introduction
of SDS (Shared Data Structure) by the SCP, the reset syndrome
needs to queried from the appropriate SDS field.

Change-Id: If9c08f1afaaa4fcf197f3186887068103855f554
Signed-off-by: Sathees Balya <sathees.balya@arm.com>
Signed-off-by: Soby Mathew <Soby.Mathew@arm.com>

Adds an undocumented build option that enables non-secure access to
the PL011 UART1.
This allows a custom build where the UART can be used as a serial debug
port for WinDbg (or other debugger) connection.

This option is not documented in the user guide, as it is provided as a
convenience for Windows debugging, and not intended for general use.
In particular, enabling non-secure access to the UART might allow
a denial of service attack!

Change-Id: I4cd7d59c2cac897cc654ab5e1188ff031114ed3c
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>

A cache flush is added in BL1, in Mbed TLS shared heap code. Thus, we
ensure that the heap info written to the DTB always gets written back to
memory.  Hence, sharing this info with other images is guaranteed.

Change-Id: I0faada31fe7a83854cd5e2cf277ba519e3f050d5
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

In Mbed TLS shared heap code, an additional sanity check is introduced
in BL2. Currently, when BL2 shares heap with BL1, it expects the heap
info to be found in the DTB. If for any reason the DTB is missing, BL2
cannot have the heap address and, hence, Mbed TLS cannot proceed. So,
BL2 cannot continue executing and it will eventually crash.  With this
change we ensure that if the DTB is missing BL2 will panic() instead of
having an unpredictable crash.

Change-Id: I3045ae43e54b7fe53f23e7c2d4d00e3477b6a446
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

This patch, firstly, makes the error messages consistent to how printed
strings are usually formatted. Secondly, it removes an unnecessary #if
directive.

Change-Id: Idbb8ef0070562634766b683ac65f8160c9d109e6
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

The Marvell A8K SoCs use the MI2CV IP core from Mentor Graphics, which
is also used by Allwinner.

As Mentor Graphics allows a lot of customization, the MI2CV in the two
SoC families are not compatible, and driver modifications are needed.

Extract the common code to a MI2CV driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

Replaces deprecated early platform setup APIs

* Replaces bl31_early_platform_setup() with bl31_early_platform_setup2()
* Replaces bl2_early_platform_setup() with bl2_early_platform_setup2()
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>

Previous changes in this series made the necessary driver additions and
updates. With those changes in-place we can add the platform.mk and
bl2_el3_setup.c to drive the boot process.

After this commit its possible to build a fully-functional TF-A for the
WaRP7 and boot from the BootROM to the Linux command prompt in secure or
non-secure mode.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch adds a callback into the BootROM's provided High Assurance Boot
(HAB) failsafe function when panicking i.e. the call is done without making
use of stack.

The HAB failsafe function allows a piece of software to call into the
BootROM and place the processor into failsafe mode.

Failsafe mode is a special mode which presents a serial download protocol
interface over UART or USB at the time of writing.

If the board has been set into secure mode, then only a signed binary can
be used to recover the board.

Thus failsafe gives a putatively secure method of performing a secure
recovery over UART or USB.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>

This patch adds entries to the mem params array for

- BL32
- BL32_EXTRA1
- BL32_EXTRA2
- BL33
- HW_CONFIG_ID

BL32 is marked as bootable to indicate that OPTEE is the thing that should
be booted next.

In our model OPTEE chain-loads onto u-boot so only BL32 is bootable.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This commit adds support for parsing a FIP pre-loaded by a previous
boot-phase such as u-boot or via ATF reading directly from eMMC.

[bod: squashing several patches from Rui, Jun and bod]
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch defines a platform_def.h describing

- FIP layout and location
- eMMC device select
- UART identity select
- System clock frequency
- Operational memory map
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

In order to link even a basic image we need to declare
REGISTER_BL_IMAGE_DESCS. This patch declares an empty structure which is
passed to REGISTER_BL_IMAGE_DESCS(). Later patches will add in some
meaningful data.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

Internal declarations for the WaRP7 port will go here. For now just include
sys/types.h.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This commit adds warp7_image_load.c with the functions

- plat_flush_next_bl_params()
- plat_get_bl_image_load_info()
- plat_get_next_bl_params()
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This commit adds a warp7_helpers.S which contains a implementation of:

- platform_mem_init
- plat_get_my_entrypoint
- plat_crash_console_init
- plat_crash_console_putc
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

The watchdog block on the IMX is mercifully simple. This patch maps the
various registers and bits associated with the block.

We are mostly only really interested in the power-down-enable (PDE) bits in
the block for the purposes of ATF.

The i.MX7 Solo Applications Processor Reference Manual details the PDE bit
as follows:

"Power Down Enable bit. Reset value of this bit is 1, which means the power
down counter inside the WDOG is enabled after reset. The software must
write 0 to this bit to disable the counter within 16 seconds of reset
de-assertion. Once disabled this counter cannot be enabled again. See
Power-down counter event for operation of this counter."

This patch does that zero write in-lieu of later phases in the boot
no-longer have the necessary permissions to rewrite the PDE bit directly.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch defines the most basic part of the CAAM and the only piece of
the CAAM silicon we are really interested in, in ATF, the CAAM control
structure.

The CAAM itself is a huge address space of some 32k, way out of scope for
the purpose we have in ATF.

This patch adds a simple CAAM init function that assigns ownership of the
CAAM job-rings to the non-secure MID with the ownership bit set to
non-secure.

This will allow later logic in the boot process such as OPTEE, u-boot and
Linux to assign job-rings as appropriate, restricting if necessary but
leaving open the main functionality of the CAAM to the Linux NS runtime.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

The QEMU platform has only been used with LOAD_IMAGE_V2=1 for some time
now and bit rot has occurred for LOAD_IMAGE_V2=0. To ease the
maintenance make LOAD_IMAGE_V2=1 mandatory and remove the platform
specific code for LOAD_IMAGE_V2=0.
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>

Enable ARM_XLAT_TABLES_LIB_V1 as ZynqMP is using
v1 library of translation tables.

With upstream patch d323af9e

,
the usage of MAP_REGION_FLAT is referring to definition in file
include/lib/xlat_tables/xlat_tables_v2.h but while preparing
xlat tables in lib/xlat_tables/xlat_tables_common.c it is referring
to include/lib/xlat_tables/xlat_tables.h which is v1 xlat tables.
Also, ZynqMP was using v1 so defined ARM_XLAT_TABLES_LIB_V1 to
use v1 xlat tables everywhere.
This fixes the issue of xlat tables failures as it takes v2
library mmap_region structure in some files and v1 in other
files.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>

The High Assurance Boot or HAB is an on-chip method of providing a
root-of-trust from the reset vector to subsequent stages in the bootup
flow of the Cortex-A7 on the i.MX series of processors.

This patch adds a simple header file with pointer offsets of the provided
set of HAH API callbacks in the BootROM.

The relative offset of the function pointers is a constant and known
quantum, a software-contract between NXP and an implementation which is
defined in the NXP HAB documentation.

All we need is the correct base offset and then we can map the set of
function pointers relative to that offset.

imx_hab_arch.h provides the correct offset and the imx_hab.h hooks the
offset to the pre-determined callbacks.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>

In order to enable compile time differences in HAB interaction, we should
split out the definition of the base address of the HAB API.

Some version of the i.MX series have different offsets from the BootROM
base for the HAB callback table.

This patch defines the header into which we will define the i.MX7 specific
offset. The offset of the i.MX7 function-callback table is simultaneously
defined.

Once done, we can latch a set of common function pointer locations from the
offset given here and if necessary change the offset for different
processors without any other code-change.

For now all we support is i.MX7 so the only offset being defined is that
for the i.MX7.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>

This patch adds snvs.c with a imx_snvs_init() function.

imx_snvs_init() sets up permissions of the RTC via the SNVS HPCOMR.

During previous work with OPTEE on the i.MX7 part we discovered that prior
to switching from secure-world to normal-world it is required to apply more
permissive permissions than are defaulted to in order for Linux to be able
to access the RTC and CAAM functionality in general.

This patch pertains to fixing the RTC permissions by way of the
HPCOMR.NPSWA_EN bit.

Once set non-privileged code aka Linux-kernel code has permissions to
access the SNVS where the RTC resides.

Perform that permissions fix in imx_snvs_init() now, with a later patch making
the call from our platform setup code.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This commit defines two things.

- The basic SNVS memory map. At the moment that is total overkill for the
  permission bits we need to set inside the SNVS but, for the sake of
  completeness define the whole SNVS area as a struct.

- The bits of the HPCOMR register

  A permission fix will need to be applied to the SNVS block prior to
  switching on TrustZone. All we need to do is waggle a bit in the HPCOMR
  register. To do that waggle we first need to define the bits of the
  HPCOMR register.

- A imx_snvs_init() function definition

  Declare the snvs_init() function so that it can be called from our
  platform setup code.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

- Add a header to define imx_csu_init().
- Defines the Central Security Unit's Config Security Level
  permission bits.
- Define CSU_CSL_OPEN_ACCESS permission bitmask
- Run a loop to setup peripheral CSU permissions
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch adds an initial AHB-to-IP TrustZone (AIPS-TZ) initialization
routine. Setting up the AIPSTZ controller is required to inform the SoC
interconnect fabric which bus-masters can read/write and if the read/writes
are buffered.

For our purposes the initial configuration is for everything to be open. We
can lock-down later on as necessary.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch defines:

- The full range of IO-mux register offsets relative to the base address of
  the IO-mux block base address.

- The bits for muxing the UART1 TX/RX lines.

- The bits for muxing the UART6 TX/RX lines.

- The pad control pad bits for the UART

Two functions are provided to configure pad muxes:

- void io_muxc_set_pad_alt_function(pad_mux_offset, alt_function)
  Takes a pad_mux_offset and sets the alt_function bit-mask supplied.
  This will have the effect of switching the pad into one of its defined
  peripheral functions. These peripheral function modes are defined in the
  NXP documentation and need to be referred to in order to correctly
  configure a new alternative-function.

- void io_muxc_set_pad_features(pad_feature_offset, pad_features)
  Takes a pad_feature_offset and applies a pad_features bit-mask to the
  indicated pad.
  This function allows the setting of PAD drive-strength, pull-up values,
  hysteresis glitch filters and slew-rate settings.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch initializes USB core clocks for the i.MX7.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch initializes the watchdog clocks for the i.MX7.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch adds an internal UART init routine that gets called from the
external facing clock init function.

In the first pass this call does an explicit disable of all UART
clock-gates. Later changes will enable only the UART clock-gates we care
about.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This set of patches adds a very minimal layer of USB enabling patches to
clock.c. Unlike the watchdog or UART blocks the USB clocks pertain to PHYs,
the main USB clock etc, not to different instances of the same IP block.

As a result this patch-set takes the clock CCGR clock identifier directly
rather than as an index of an instance of blocks of the same type.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch adds a set of functions to enable the clock for each of the
watchdog IP blocks.

Unlike the MMC and UART blocks, the watchdog blocks operate off of the one
root clock, only the clock-gates are enable/disabled individually.

As a consequence the function clock_set_wdog_clk_root_bits() is used to set
the root-slice just once for all of the watchdog blocks.

Future implementations may need to change this model but for now on the one
supported processor and similar NXP SoCs this model should work fine.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch adds an API to configure up the base USDHC clocks, taking a
bit-mask of silicon specific bits as an input from a higher layer in order
to direct the necessary clock source.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>