GitLab

Previous changes in this series made the necessary driver additions and
updates. With those changes in-place we can add the platform.mk and
bl2_el3_setup.c to drive the boot process.

After this commit its possible to build a fully-functional TF-A for the
WaRP7 and boot from the BootROM to the Linux command prompt in secure or
non-secure mode.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch adds a callback into the BootROM's provided High Assurance Boot
(HAB) failsafe function when panicking i.e. the call is done without making
use of stack.

The HAB failsafe function allows a piece of software to call into the
BootROM and place the processor into failsafe mode.

Failsafe mode is a special mode which presents a serial download protocol
interface over UART or USB at the time of writing.

If the board has been set into secure mode, then only a signed binary can
be used to recover the board.

Thus failsafe gives a putatively secure method of performing a secure
recovery over UART or USB.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>

This patch adds entries to the mem params array for

- BL32
- BL32_EXTRA1
- BL32_EXTRA2
- BL33
- HW_CONFIG_ID

BL32 is marked as bootable to indicate that OPTEE is the thing that should
be booted next.

In our model OPTEE chain-loads onto u-boot so only BL32 is bootable.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This commit adds support for parsing a FIP pre-loaded by a previous
boot-phase such as u-boot or via ATF reading directly from eMMC.

[bod: squashing several patches from Rui, Jun and bod]
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch defines a platform_def.h describing

- FIP layout and location
- eMMC device select
- UART identity select
- System clock frequency
- Operational memory map
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

In order to link even a basic image we need to declare
REGISTER_BL_IMAGE_DESCS. This patch declares an empty structure which is
passed to REGISTER_BL_IMAGE_DESCS(). Later patches will add in some
meaningful data.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

Internal declarations for the WaRP7 port will go here. For now just include
sys/types.h.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This commit adds warp7_image_load.c with the functions

- plat_flush_next_bl_params()
- plat_get_bl_image_load_info()
- plat_get_next_bl_params()
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This commit adds a warp7_helpers.S which contains a implementation of:

- platform_mem_init
- plat_get_my_entrypoint
- plat_crash_console_init
- plat_crash_console_putc
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

The watchdog block on the IMX is mercifully simple. This patch maps the
various registers and bits associated with the block.

We are mostly only really interested in the power-down-enable (PDE) bits in
the block for the purposes of ATF.

The i.MX7 Solo Applications Processor Reference Manual details the PDE bit
as follows:

"Power Down Enable bit. Reset value of this bit is 1, which means the power
down counter inside the WDOG is enabled after reset. The software must
write 0 to this bit to disable the counter within 16 seconds of reset
de-assertion. Once disabled this counter cannot be enabled again. See
Power-down counter event for operation of this counter."

This patch does that zero write in-lieu of later phases in the boot
no-longer have the necessary permissions to rewrite the PDE bit directly.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch defines the most basic part of the CAAM and the only piece of
the CAAM silicon we are really interested in, in ATF, the CAAM control
structure.

The CAAM itself is a huge address space of some 32k, way out of scope for
the purpose we have in ATF.

This patch adds a simple CAAM init function that assigns ownership of the
CAAM job-rings to the non-secure MID with the ownership bit set to
non-secure.

This will allow later logic in the boot process such as OPTEE, u-boot and
Linux to assign job-rings as appropriate, restricting if necessary but
leaving open the main functionality of the CAAM to the Linux NS runtime.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

The High Assurance Boot or HAB is an on-chip method of providing a
root-of-trust from the reset vector to subsequent stages in the bootup
flow of the Cortex-A7 on the i.MX series of processors.

This patch adds a simple header file with pointer offsets of the provided
set of HAH API callbacks in the BootROM.

The relative offset of the function pointers is a constant and known
quantum, a software-contract between NXP and an implementation which is
defined in the NXP HAB documentation.

All we need is the correct base offset and then we can map the set of
function pointers relative to that offset.

imx_hab_arch.h provides the correct offset and the imx_hab.h hooks the
offset to the pre-determined callbacks.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>

In order to enable compile time differences in HAB interaction, we should
split out the definition of the base address of the HAB API.

Some version of the i.MX series have different offsets from the BootROM
base for the HAB callback table.

This patch defines the header into which we will define the i.MX7 specific
offset. The offset of the i.MX7 function-callback table is simultaneously
defined.

Once done, we can latch a set of common function pointer locations from the
offset given here and if necessary change the offset for different
processors without any other code-change.

For now all we support is i.MX7 so the only offset being defined is that
for the i.MX7.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>

This patch adds snvs.c with a imx_snvs_init() function.

imx_snvs_init() sets up permissions of the RTC via the SNVS HPCOMR.

During previous work with OPTEE on the i.MX7 part we discovered that prior
to switching from secure-world to normal-world it is required to apply more
permissive permissions than are defaulted to in order for Linux to be able
to access the RTC and CAAM functionality in general.

This patch pertains to fixing the RTC permissions by way of the
HPCOMR.NPSWA_EN bit.

Once set non-privileged code aka Linux-kernel code has permissions to
access the SNVS where the RTC resides.

Perform that permissions fix in imx_snvs_init() now, with a later patch making
the call from our platform setup code.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This commit defines two things.

- The basic SNVS memory map. At the moment that is total overkill for the
  permission bits we need to set inside the SNVS but, for the sake of
  completeness define the whole SNVS area as a struct.

- The bits of the HPCOMR register

  A permission fix will need to be applied to the SNVS block prior to
  switching on TrustZone. All we need to do is waggle a bit in the HPCOMR
  register. To do that waggle we first need to define the bits of the
  HPCOMR register.

- A imx_snvs_init() function definition

  Declare the snvs_init() function so that it can be called from our
  platform setup code.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

- Add a header to define imx_csu_init().
- Defines the Central Security Unit's Config Security Level
  permission bits.
- Define CSU_CSL_OPEN_ACCESS permission bitmask
- Run a loop to setup peripheral CSU permissions
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch adds an initial AHB-to-IP TrustZone (AIPS-TZ) initialization
routine. Setting up the AIPSTZ controller is required to inform the SoC
interconnect fabric which bus-masters can read/write and if the read/writes
are buffered.

For our purposes the initial configuration is for everything to be open. We
can lock-down later on as necessary.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch defines:

- The full range of IO-mux register offsets relative to the base address of
  the IO-mux block base address.

- The bits for muxing the UART1 TX/RX lines.

- The bits for muxing the UART6 TX/RX lines.

- The pad control pad bits for the UART

Two functions are provided to configure pad muxes:

- void io_muxc_set_pad_alt_function(pad_mux_offset, alt_function)
  Takes a pad_mux_offset and sets the alt_function bit-mask supplied.
  This will have the effect of switching the pad into one of its defined
  peripheral functions. These peripheral function modes are defined in the
  NXP documentation and need to be referred to in order to correctly
  configure a new alternative-function.

- void io_muxc_set_pad_features(pad_feature_offset, pad_features)
  Takes a pad_feature_offset and applies a pad_features bit-mask to the
  indicated pad.
  This function allows the setting of PAD drive-strength, pull-up values,
  hysteresis glitch filters and slew-rate settings.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch initializes USB core clocks for the i.MX7.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch initializes the watchdog clocks for the i.MX7.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch adds an internal UART init routine that gets called from the
external facing clock init function.

In the first pass this call does an explicit disable of all UART
clock-gates. Later changes will enable only the UART clock-gates we care
about.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This set of patches adds a very minimal layer of USB enabling patches to
clock.c. Unlike the watchdog or UART blocks the USB clocks pertain to PHYs,
the main USB clock etc, not to different instances of the same IP block.

As a result this patch-set takes the clock CCGR clock identifier directly
rather than as an index of an instance of blocks of the same type.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch adds a set of functions to enable the clock for each of the
watchdog IP blocks.

Unlike the MMC and UART blocks, the watchdog blocks operate off of the one
root clock, only the clock-gates are enable/disabled individually.

As a consequence the function clock_set_wdog_clk_root_bits() is used to set
the root-slice just once for all of the watchdog blocks.

Future implementations may need to change this model but for now on the one
supported processor and similar NXP SoCs this model should work fine.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch adds an API to configure up the base USDHC clocks, taking a
bit-mask of silicon specific bits as an input from a higher layer in order
to direct the necessary clock source.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch adds an API to configure up the base UART clocks, taking a
bit-mask of silicon specific bits as an input from a higher layer in order
to direct the necessary clock source.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This commit:

- Defines a clock stub with a conjoined header defining the clock
  memory map.

- Defines the CCM Clock Gating Register which comes in a quadrumvirate
  register set to read, set, clear and toggle individual clock gates into
  one of four states based bitmask.

  00: Domain clocks not needed
  01: Domain clocks needed when in RUN
  10: Domain clocks needed when in RUN and WAIT
  11: Domain clocks needed all the time

- Defines clock control register bits

  There are various quadrumvirate register blocks target-root, misc-root,
  post-root, pre-root in the CCM.

  The number of registers is huge but the four registers in each
  quadrumvirate block contain the same bits, so the number of bit
  definitions is actually quite low.

- Defines clock identifiers

  An array of clock gates is provided in the CCM block. In order to index
  that array and thus enable/disable clock gates for the right components,
  we need to provide meaningful names to the indices.

  Section 5.2.5 of the i.MX7 Solo Application Processor Reference Manual
  Rev 0.1 provides the relevant details.

- Defines target mux select bits
  This is a comprehensive definition of the target clock mux select bits.
  These bits are required to correctly select the clock source. Defining
  all of the bits up-front even for unused blocks in ATF means we can
  switch on any block we want at a later date without having to write new
  code in the clock-mux layer.

- Defines identifier indices into root-slice array
  The root-slice array of control registers has a specific set of indices,
  which differ from the clock-gate indices.

- Provides a clock gate enable/disable routine
  Provides a clock-gate enable/disable routine via the set/clr
  registers in a given clock-gate control register block.

  This index passed should be one of the enums associated with CCM and
  depending on enable/disable being passed either set or clr will be
  written to.

  The Domain0 bits are currently the only bits targeted by this write, more
  work may need to be done on the domain bits in subsequent patches as a
  result.

- imx: Adds set/clr routines to clock layer

  Adds a set and clr routine to the clock layer. These routines allow us to
  access the set and clear registers of the "target" block registers. These
  are the registers where we select the clock source from the available list.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

In order to have some common code shared between similar SOCs its pretty
common to have IP blocks reused. In reusing those blocks we frequently need
to map compatible blocks to different addresses depending on the SOC.

This patch adds a basic memory map of the i.MX7 based on the "Cortex-A7
Memory Map" section 2.12 of "i.MX7Solo Applications Processor Reference
Manual, Rev 0.1 08/2016"

In memory map terms the i.MX7S and i.MX7D are identical with the D
variant containing two Cortex-A7 cores plus a Cortex-M core and the S
variant containing one Cortex-A7 and one Cortex-M.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

Add USDHC driver to support boot EMMC. Only initialization
and single/multiple block read are tested.

[bod: fixed checkpatch.pl complaints]
[bod: changed name to imx_usdhc for namespace consistency]
[bod: squashed antecedent fixes into this one patch]
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

Add missing response type for SWITCH command and STOP_TRANSMISSION
so that controller can be configured accordingly.

[bod: ported this change from Jun's eMMC patches to the MMC driver]
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

The R3 response type definition should be (1 << 0). Make sure we define the
expected response code in the appropriate fashion.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

Add response flag into ID definition so that driver does not
need to handle it again.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

Add delay timer API so that it can be called by delay timer
layer and used as delay timer globally.

[bod: changed name from imx_delay_timer -> imx_gpt ]
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

This patch does two main things

- It implements the crash console UART init in assembly, as a
  hard-coded 115200 8N1 assumed from the 24 MHz clock.

  If the clock setup code has not run yet, this code can't work but,
  setting up clocks and clock-gates is way out of scope for this type of
  recovery function.

- It adds code to write a character out of the NXP UART without using any
  stack-based operations when doing so.

- Provides support for crash console in DCE or DTE mode.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

- Adds a simple register read/write abstraction to cut-down on the
  amount of typing and text required to access UART registers in this driver.

- Adds a console getc() callback.

- Adds a console putc() callback, translating '\n' to '\r' + '\n'.

- Initializes the MXC UART, take a crude method of calculating the
  BAUD rate generator. The UART clock-gates must have been enabled prior
  to launching the UART init code.
  Special care needs to be taken to ensure the UBIR is initialized before the
  UBMR and we need to ensure that UCR2.SRST comes good before trying to
  program other registers associated with the UART.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

Fix some MISRA defect in log helpers

No functional changes.

Change-Id: I850f08718abb69d5d58856b0e3de036266d8c2f4
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

No functional changes.

Change-Id: I907aa47565af2a6c435a5560041fd2b59e65c25c
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Some MISRA fixes in BL31, cci and smmu

context_mgmt: Fix HANDLE_EA_EL3_FIRST implementation

MISRA fixes for the GIC driver