GitLab

This patch allows the ARM Platforms to specify the TZC regions to be
specified to the ARM TZC helpers in arm_tzc400.c and arm_tzc_dmc500.c.
If the regions are not specified then the default TZC region will be
configured by these helpers.

This override mechanism allows specifying special regions for TZMP1
usecase.
Signed-off-by: Summer Qin <summer.qin@arm.com>

Add support for System Guidance for Infrastructure platform SGI575.

Change-Id: I0125c2ed4469fbc8367dafcc8adce770b6b3147d
Signed-off-by: Nariman Poushin <nariman.poushin@linaro.org>

Ensure (where possible) that switch statements in plat comply with MISRA
rules 16.1 - 16.7.

Change-Id: Ie4a7d2fd10f6141c0cfb89317ea28a755391622f
Signed-off-by: Jonathan Wright <jonathan.wright@arm.com>

When the source code says 'SMCC' it is talking about the SMC Calling
Convention. The correct acronym is SMCCC. This affects a few definitions
and file names.

Some files have been renamed (smcc.h, smcc_helpers.h and smcc_macros.S)
but the old files have been kept for compatibility, they include the
new ones with an ERROR_DEPRECATED guard.

Change-Id: I78f94052a502436fdd97ca32c0fe86bd58173f2f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

x3 will be assigned by the folloing instructions.
So the first instruction is not needed any more.

old method:
  (ClusterId * FVP_MAX_CPUS_PER_CLUSTER)
+ (CPUId * FVP_MAX_PE_PER_CPU)
+ ThreadId

it should be
  (ClusterId * FVP_MAX_CPUS_PER_CLUSTER) * FVP_MAX_PE_PER_CPU
+ (CPUId * FVP_MAX_PE_PER_CPU)
+ ThreadId

which can be simplified as:
(ClusterId * FVP_MAX_CPUS_PER_CLUSTER + CPUId) * FVP_MAX_PE_PER_CPU + ThreadId
Signed-off-by: Wang Feng <feng_feng.wang@spreadtrum.com>

The FVP platform port for SP_MIN (BL32) didn't map the flash memory
in BL32 for stroring the mem_protect enable state information leading
to synchronous exception. The patch fixes it by adding the region to
the BL32 mmap tables.

Change-Id: I37eec83c3e1ea43d1b5504d3683eebc32a57eadf
Signed-off-by: Joel Hutton <Joel.Hutton@Arm.com>

Previously, Juno used to depend on the SSC_GPRETN register to inform
about the reset syndrome. This method was removed when SCP migrated
to the SDS framework. But even the SDS framework doesn't report the
reset syndrome correctly and hence Juno failed to enter Firmware
update mode if BL2 authentication failed.

In addition to that, the error code populated in V2M_SYS_NVFLAGS register
does not seem to be retained any more on Juno across resets. This could
be down to the motherboard firmware not doing the necessary to preserve
the value.

Hence this patch modifies the Juno platform to use the same mechanism to
trigger firmware update as FVP which is to corrupt the FIP TOC on
authentication failure. The implementation in `fvp_err.c` is made common
for ARM platforms and is moved to the new `arm_err.c` file in
plat/arm/common folder. The BL1 and BL2 mmap table entries for Juno
are modified to allow write to the Flash memory address.

Change-Id: Ica7d49a3e8a46a90efd4cf340f19fda3b549e945
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This issue was detected when testing FWU on Juno. The Timer
`timer_ops` was not being initialized before being used by
the SDS driver on Juno. This patch adds the call to
`generic_delay_timer_init()` during bl2u_early_platform_setup().
This is done generically for all ARM platforms because the
cost involved is minimal.

Change-Id: I349cf0bd1db68406eb2298b65f9c729f792cabdc
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch removes default platform implementations of sp_min
platform APIs from plat/common/aarch32/plat_common.c. The APIs
are now implemented in `plat_sp_min_common.c` file within the
same folder.

The ARM platform layer had a weak definition of sp_min_platform_setup2()
which conflicted with the weak definition in the common file. Hence this
patch fixes that by introducing a `plat_arm_` version of the API thus
allowing individual boards within ARM platforms to override it if they
wish to.

Fixes ARM-software/tf-issues#559

Change-Id: I11a74ecae8191878ccc7ea03f12bdd5ae88faba5
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This was correct according to the model specifications , but it seems
that FVP doesn't implement it. It is safer to use the size exposed by
the DTB which is currently used by Linux.

Change-Id: I9aabe3284a50ec2a36ed94966eb7e4ddf37cec3b
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Rule 8.4: A compatible declaration shall be visible when
          an object or function with external linkage is defined

Fixed for:
	make DEBUG=1 PLAT=juno LOG_LEVEL=50 all

Change-Id: Ic8f611da734f356566e8208053296e6c62b54709
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Rule 8.4: A compatible declaration shall be visible when
          an object or function with external linkage is defined

Fixed for:
	make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all

Change-Id: I7c2ad3f5c015411c202605851240d5347e4cc8c7
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Rule 8.3: All declarations of an object or function shall
          use the same names and type qualifiers.

Fixed for:

	make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all

Change-Id: I48201c9ef022f6bd42ea8644529afce70f9b3f22
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

FVPs that model DynamIQ configuration implements all CPUs in a single
cluster. I.e., such models have a single cluster with more than 4 CPUs.
This differs from existing default build configuration for FVP where up
to 4 CPUs are assumed per cluster.

To allow building for DynamIQ configuration, promote the macro
FVP_MAX_CPUS_PER_CLUSTER as a build option to have it set from the build
command line. The value of the build option defaults to 4.

Change-Id: Idc3853bc95f680869b434b011c2dbd733e40c6ce
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The SCP binaries provided in the 17.10 Linaro release (and onwards)
have migrated to the SCMI/SDS protocols. Therefore, the ARM TF should
now use the corresponding drivers by default.

This patch changes the default value of the CSS_USE_SCMI_SDS_DRIVER
build option to 1 for Juno.

Change-Id: Idb7e3c6af582f49e332167a2158703c2d781b437
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

MISRA C-2012 Rule 7.3 violation: lowercase l shall not be used as literal suffixes.

This patch resolves this for the ULL() macro by using ULL suffix instead
of the ull suffix.

Change-Id: Ia8183c399e74677e676956e8653e82375d0e0a01
Signed-off-by: David Cunado <david.cunado@arm.com>

This patch restricts building the dynamic config DTBs to the Unix
build environment as the Device Tree compiler may not be available
on other build environments.

Change-Id: Ie690e80010a174300e966240fd977b37561156e0
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch also fixes the assumption that the counters are disabled on
the resume path.  This is incorrect as the AMU counters are enabled
early in the CPU reset function before `cpuamu_context_restore()`
runs.

Change-Id: I38a94eb166a523f00de18e86860434ffccff2131
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

This patch also fixes `cpuamu_write_cpuamcntenclr_el0()` to use an MSR
instruction instead of an MRS instruction.

Change-Id: Ia6531f64b5ebc60ba432124eaa8d8eaccba40ed0
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Change-Id: I1d85b76af002b8b672fcaeca94939b7420bc8243
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch adds TB_FW_CONFIG for FVP and allows FVP
to select the appropriate HW_CONFIG to include in the
fip. The HW_CONFIG for FVP is selected via `FVP_HW_CONFIG_DTS`
build option. The TB_FW_CONFIG specifies the load address of
HW_CONFIG to BL2. Since currently the load address is different
between AARCH32 and AARCH64, 2 separate TB_FW_CONFIGs are
maintained for the 2 modes.

Change-Id: Ide8581e752dfa900087f5895c775073c841c0daf
Signed-Off-By: Soby Mathew <soby.mathew@arm.com>

The patch adds the necessary changes to load HW_CONFIG in BL2 for
ARM Platforms :

1. The load address of HW_CONFIG is specified via the `hw_config_addr`
property in TB_FW_CONFIG is loaded by BL1. The `hw_config_max_size`
property defines the maximum size to be expected for the HW_CONFIG.
The `arm_dyn_cfg_helpers.c` and corresponding header implements
utility functions to parse these DT properties defined.
The `arm_dyn_cfg.c` implements wrappers to these helpers to enable
them to be invoked from ARM platform layer.

2. `HW_CONFIG` is added to the `bl2_mem_params_descs[]` array which is
the list of images to be loaded by BL2.

3. The `libfdt` sources are now included when BL2 is built

4. A new helper `populate_next_bl_params_config()` is introduced in
desc_image_load.c to populate the subsequent executable BL images
with the `hw_config` and the corresponding `fw_config` if available.
The `plat_get_next_bl_params()` API for ARM platforms is modified to
invoke this new helper.

5. The implementation of `bl2_early_platform_setup2()` is modified to
consider `arg0` as well in addition to `arg1` passed from BL1.

6. Bump up the BL2 size for Juno to accommodate the inclusion of libfdt.

Change-Id: I80f1554adec41753e0d179a5237364f04fe13a3f
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch modifies the bl1_platform_setup() API to load and authenticate
TB_FW_CONFIG in BL1. The load address of the same is passed on to BL2 in
`arg0` of entrypoint info. The fvp_io_storage.c and arm_io_storage.c also
adds entries corresponding to TB_FW_CONFIG. A helper function
`arm_load_tb_fw_config()` is added to load and authenticate TB_FW_CONFIG
if present.

Change-Id: Ie7bce667b3fad2b1a083bbcbc0a773f9f04254b1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch migrates the ARM Standard platforms to the new BL
handover interface. The arm_blx_early_platform_setup() functions
are also modified to take in 4 arguments. The `ARM_BL31_PLAT_PARAM_VAL`
value passed to BL31 from BL2 is now in arg3 in preparation of dynamic
configuration arguments.

Change-Id: I33e8e61325a19e7a7127b1ff203c3b86921bf153
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Change-Id: I93e491fde2a991fc39584c2762f33cbea40541e3
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Change-Id: Iadb21bb56f2e61d7e6aec9b3b3efd30059521def
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

The console core flush API expects the base address in the first
register, but ARM helpers currently sets the second register with the
base address. This causes an assert failure.

This patch fixes that.

Change-Id: Ic54c423cd60f2756902ab3cfc77b3de2ac45481e
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

In the next commit, I need the image name in lowercase because
output files are generally named in lowercase.

Unfortunately, TOOL_ADD_IMG takes the first argument in uppercase
since we generally use uppercase Make variables.

make_helpers/build_macros.mk provides 'uppercase' macro to convert
a string into uppercase, but 'lowercase' does not exist.  We can
implement it if we like, but it would be more straightforward to
change the argument of TOOL_ADD_IMG.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Now FIP_ADD_IMG takes care of both fiptool and cert_create
symmetrically.  Rename it so that it matches the behavior.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The build system supports generating two FIP images, fip and fwu_fip.
Accordingly, we have similar build macros.

   FIP_ADD_PAYLOAD   <-->  FWU_FIP_ADD_PAYLOAD
   CERT_ADD_CMD_OPT  <-->  FWU_CERT_ADD_CMD_OPT
   FIP_ADD_IMG       <-->  FWU_FIP_ADD_IMG

The duplicated code increases the maintenance burden.  Also, the build
rule of BL2U looks clumsy - we want to call MAKE_BL to compile it from
source files, but we want to put it in fwu_fip.  We can not do it in a
single macro call since the current MAKE_BL does not support fwu_fip.

To refactor those in a clean way is to support one more argument to
specify the FIP prefix.  If it is empty, the images are targeted to
fip, whereas if the argument is "FWU_", targeted to fwu_fip.

The build macros prefixed with FWU_ go away.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This patch maps the devices in the first GB of the system address map
on the FVP into the S-EL1&0 translation regime when SPM support is
enabled. This grants the Secure Partition access to the devices in
this region, for example the memory-mapped Generic Timer device.

Change-Id: I3aeea65f859ecbe83efde2acee20c55500c451bc
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

This patch modifies the makefiles to avoid the definition
of BL1_SOURCES and BL2_SOURCES in the tbbr makefiles, and
it lets to the platform makefiles to define them if they
actually need these images. In the case of BL2_AT_EL3
BL1 will not be needed usually because the Boot ROM will
jump directly to BL2.

Change-Id: Ib6845a260633a22a646088629bcd7387fe35dcf9
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

This patch add supports for the new API added for BL2 at EL3 for
FVP. We don't have a non-TF Boot ROM for FVP, but this option can be
tested setting specific parameters in the model.

The bl2 image is loaded directly in memory instead of being loaded
by a non-TF Boot ROM and the reset address is changed:

	--data cluster0.cpu0=bl2.bin@0x4001000
	-C cluster0.cpu0.RVBAR=0x4001000

These parameters mean that in the cold boot path the processor will
jump to BL2 again. For this reason, BL2 is loaded in dram in this
case, to avoid other images reclaiming BL2 memory.

Change-Id: Ieb2ff8535a9e67ccebcd8c2212cad366e7776422
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Change-Id: I504d3f65ca5829bc1f4ebadb764931f8379ee81f
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

To allow BL31 to grow in SRAM, move TSP in TZC secured DRAM
by default.

Increase the BL31 max limit by one page.

Change-Id: Idd3479be02f0f9bafac2f275376d7db0c2015431
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

With this patch, ARM platforms are expected to define the macros
PLAT_ARM_SDEI_PRIVATE_EVENTS and PLAT_ARM_SDEI_SHARED_EVENTS as a list
of private and shared events, respectively. This allows for individual
platforms to define their own events.

Change-Id: I66851fdcbff83fd9568c2777ade9eb12df284b49
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

After returning from SYSTEM_SUSPEND state, BL31 reconfigures the
TrustZone Controller during the boot sequence. If BL31 is placed in
TZC-secured DRAM, it will try to change the permissions of the memory it
is being executed from, causing an exception.

The solution is to disable SYSTEM_SUSPEND when the Trusted Firmware has
been compiled with ``ARM_BL31_IN_DRAM=1``.

Change-Id: I96dc50decaacd469327c6b591d07964726e58db4
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Common code mustn't include ARM platforms headers.

Change-Id: Ib6e4f5a77c2d095e6e8c3ad89c89cb1959cd3043
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch allows non-secure bus masters to access TZC region0 as well
as the EL3 Payload itself.

Change-Id: I7e44f2673a2992920d41503fb4c57bd7fb30747a
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Pre-v8.2 platforms such as the Juno platform does not have
the Scalable Vector Extensions implemented and so the build
option ENABLE_SVE is set to zero.

This has a minor performance improvement with no functional
impact.

Change-Id: Ib072735db7a0247406f8b60e325b7e28b1e04ad1
Signed-off-by: David Cunado <david.cunado@arm.com>