GitLab

This change is to add ethernet and voltage regulator nodes into
a5ds devicetree.

Change-Id: If9ed67040d54e76af1813c9f99835f51f617e9df
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>

The dts file now contains a CPU map that precisely describes the
topology including thread nodes. The map was also extended to have 16
PEs to be able to test multithreaded FVPs with 8 cores in the same
cluster.
Signed-off-by: Imre Kis <imre.kis@arm.com>
Change-Id: If39559b05d20bfd68d0ecf830ddcbc5233b288a0

This patch allows to use DDR address in memory node because on FPGA we
typically use DDR instead of shared RAM.

This patch also modifies the kernel arguments to allow the rootfs to be
mounted from a direct mapping of the QSPI NOR flash using the physmap
driver in the kernel. This allows to support CRAMFS XIP.

Change-Id: I4e2bc6a1f48449c7f60e00f5f1a698df8cb2ba89
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>

Adding support for 32MHz UART clock and selecting it as the
default UART clock

Change-Id: I9541eaff70424e85a3b5ee4820ca0e7efb040d2c
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>

DynamIQ based designs have upto 8 CPUs in each cluster. This
patch fixes the device tree node which describes the topology
of the CPU for DynamIQ FVP Model.

Change-Id: I7146bc79029ce38314026d4853e5b6406863725c
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

Remove second flash node as only one must be used
by QSPI NOR driver.

Change-Id: I48189f2fdf4e0455aabe7d4cd9b2f3d36bb9cfb5
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

Include the required FMC2 pinmux definition for the
NAND management.

Change-Id: I80333deacdf3444b2f21f17f2fb5919e569a3591
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

Using the /include/ syntax, the include was evaluated by dtc, only after running
the preprocessor, therefore the .dtsi files were not preprocessed. This patch
adds the #include syntax instead. Evaluating this and preprocessing the files
now happens in a single step, done by the C preprocessor.

Change-Id: I6d0104b6274316fc736e84973502a4d6c2c9d6e0
Signed-off-by: Balint Dobszay <balint.dobszay@arm.com>

Correct the system, timer and uart frequencies to successfully run
the stack on FPGA
Correct Cortex-A5MPcore to 8 word granularity for Cache writeback

Change-Id: I2c59c26b7dca440791ad39f2297c68ae513da7b6
Signed-off-by: Avinash Mehta <avinash.mehta@arm.com>

Same enable method is used by all the four cores. So,
make it globally for all the cores instead of adding
it to individual level.

Change-Id: I9b5728b0e0545c9e27160ea586009d929eb78cad
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>

This change is to add L2 cache node into a5ds device tree.

Change-Id: I64b4b3e839c3ee565abbcd1567d1aa358c32d947
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>

The new dts file overrides the MPIDR values of the processing elements
which were defined in the common dtsi file. The new dts file defines
four cores in a single cluster, each core having two threads.
Signed-off-by: Imre Kis <imre.kis@arm.com>
Change-Id: I0f8d8d250289077aee11eede4508871bb61dbc88

LTDC modifies the clock frequency to adapt it to the display. Such
frequency change is not detected by the FDCAN driver that instead
caches the value at probe and pretends to use it later.

This change fixes the issue by moving the FDCAN to PLL4_R,
leaving the LTDC alone on PLL4_Q.
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: I8230868b2b5fd6deb6e3f9dc3911030d8d484c58

Enable cores 1-3 using psci. On receiving the smc call from kernel,
core 0 will bring the secondary cores out pen and signal an event for
the cores. Currently on switching the cores is enabled i.e. it is not
possible to suspend, switch cores off, etc.

Change-Id: I6087e1d2ec650e1d587fd543efc1b08cbb50ae5f
Signed-off-by: Usama Arif <usama.arif@arm.com>

This commit adds authentication binary support for STM32MP1.
It prints the bootrom authentication result if signed
image is used and authenticates the next loaded STM32 images.
It also enables the dynamic translation table support
(PLAT_XLAT_TABLES_DYNAMIC) to use bootrom services.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: Iba706519e0dc6b6fae1f3dd498383351f0f75f51

RevC models have the MT bit set and the affinities shifted in the MPIDR
register. To make the Linux able to boot all CPUs it needs a modified
DTS file containing the shifted affinity values.

Beside these values the DTS files should be the same so the common part
was moved into a new file which is included in the DTS files with
shifted and non-shifted affinities.

The same setup already exists for 64 bit systems.
Signed-off-by: Imre Kis <imre.kis@arm.com>
Change-Id: I90f7b9c8d8a24c9b3f97232441dbe0a29aa8976d

This patch adds support for Corstone-700 foundation IP, which integrates
both Cortex-M0+ and Cortex-A(Host) processors in one handy, flexible
subsystem.
This is an example implementation of Corstone-700 IP host firmware.

Cortex-M0+ will take care of boot stages 1 and 2(BL1/BL2) as well as
bringing Host out RESET. Host will start execution directly from BL32 and
then will jump to Linux.

It is an initial port and additional features are expected to be added
later.

Change-Id: I7b5c0278243d574284b777b2408375d007a7736e
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>

This patch adds support for Cortex-A5 FVP for the
DesignStart program. DesignStart aims at providing
low cost and fast access to Arm IP.

Currently with this patch only the primary CPU is booted
and the rest of them wait for an interrupt.
Signed-off-by: Usama Arif <usama.arif@arm.com>
Change-Id: I3a2281ce6de2402dda4610a89939ed53aa045fab

Update DDR parameters to version 1.45.
Remove useless sdmmc1_dir_pins_b node.
Add USART3 and UART7 nodes.
Correct a PMIC value for USB regulator.
Add TIMER12, TIMER15, CRYP, HASH and USBOTG_HS nodes.
Update DTSI file for SDMMC compatible, but overwrite it with the former
name.
Move BSEC board_id node to boards DTS files, as this OTP is specific to
STMicroelectronics boards.

Change-Id: If4d2fe090c6a8368afe8e21e5ac70579911d3939
Signed-off-by: Yann Gautier <yann.gautier@st.com>

The system configuration controller is mainly used to manage
the compensation cell and other IOs and system related settings.

The SYSCFG driver is in charge of configuring masters on the interconnect,
IO compensation, low voltage boards, or pull-ups for boot pins.
All other configurations should be handled in Linux drivers requiring it.

Device tree files are also updated to manage vdd-supply regulator.

Change-Id: I10fb513761a7d1f2b7afedca9c723ad9d1bccf42
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>

DTC issues below warnings for STM32MP1 platform for using upper case
in unit address:

fdts/stm32mp15-ddr.dtsi:8.20-151.5: Warning (simple_bus_reg): /soc/ddr@5A003000: simple-bus unit address format error, expected "5a003000"
fdts/stm32mp157c-security.dtsi:9.25-13.5: Warning (simple_bus_reg): /soc/stgen@5C008000: simple-bus unit address format error, expected "5c008000"

Fix this by using the lower case unit address for concerned nodes.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Change-Id: Id3d19ac3b47ec6bcea2bd3382225e2e923dc4a70

Add board support for Avenger96 board from Arrow Electronics. This
board is based on STM32MP157A SoC and is one of the 96Boards Consumer
Edition platform.

More information about this board can be found in 96Boards website:
https://www.96boards.org/product/avenger96/

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Change-Id: Ic905f26c38d03883c6e4ea221b4b275a4b534857

This node is added in a new file stm32mp157c-security.dtsi.
This node includes OTPs that should be shadowed and made readable
to non secure world.
Explicitly add status and secure-status, as these OTPs are accessible
by secure and non-secure world.

The stgen node is also moved to this file.

Change-Id: I3c89a01588d2e411fecfc44997e1c5df2fc37cad
Signed-off-by: Yann Gautier <yann.gautier@st.com>

STM32MP1 chip embeds a dual Cortex-A7 and a Cortex-M4.
The support for Cortex-M4 clocks is added when configuring the clock tree.
Some minimal security features to allow communications between A7 and M4
are also added.

Change-Id: I60417e244a476f60a2758f4969700b2684056665
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Cortex A5 doesnt support VFP, Large Page addressing and generic timer
which are addressed in this patch. The device tree for Cortex a5
is also included.

Change-Id: I0722345721b145dfcc80bebd36a1afbdc44bb678
Signed-off-by: Usama Arif <usama.arif@arm.com>

This patch adds support for Versatile express FVP (Fast models).
Versatile express is a family of platforms that are based on ARM v7.
Currently this port has only been tested on Cortex A7, although it
should work with other ARM V7 cores that support LPAE, generic timers,
VFP and hardware divide. Future patches will support other
cores like Cortex A5 that dont support features like LPAE
and hardware divide. This platform is tested on and only expected to
work on single core models.

Change-Id: I10893af65b8bb64da7b3bd851cab8231718e61dd
Signed-off-by: Usama Arif <usama.arif@arm.com>

Add the device tree files to support the 2 discovery boards: DK1 & DK2.

Change-Id: I90b4797dc69bd0aab1b643a72c932ead48a03c1f
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Regulator configuration at boot takes more information from DT.
I2C configuration from DT is done in I2C driver.
I2C driver manages more transfer modes.
The min voltage of buck1 should also be increased to 1.2V,
else the platform does not boot.

Heavily modifies stm32_i2c.c since many functions move inside the source
file to remove redundant declarations.

Change-Id: I0bee5d776cf3ff15e687427cd6abc06ab237d025
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>

The drivers are also updated to reflect the changes.
Set RCC as non-secure.

Change-Id: I568fa1f418355830ad1d4d1cdcdb910fb362231b
Signed-off-by: Yann Gautier <yann.gautier@st.com>

This is the correct name of the IP.
Rename stm32mp1_pmic files to stm32mp_pmic.

Change-Id: I238a7d1f9a1d099daf7788dc9ebbd3146ba2f15f
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Those device tree files are taken from STM32MP1 U-Boot and Linux.
And they are updated to fit TF-A needs.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

Since FVP enables dynamic configuration by default, the DT blobs are
compiled from source and included in FIP during build. Hence this
patch removes the dtb files from the `fdts` folder.

Change-Id: Ic155ecd257384a33eb2aa38c9b4430e47b09cd31
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

DTC generates warnings when unit names begin with 0, or
when a node containing a reg or range property doesn't have a unit name
in the node name. This patch fixes those cases.

Change-Id: If24ec68ef3034fb3fcefb96c5625c47a0bbd8474
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

DynamIQ platforms host all CPUs in a single cluster. This patch adds a
DTS and DTB for DynamicQ platforms hosting up to 8 CPUs.

Change-Id: I2d97bc740ac3062818767e7251020644f5bb9100
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The commit 8d2c4977

 changed the interrupt map in `rtsm_ve-motherboard.dtsi`
for the Linux FDT sources to be compatible for FreeBSD. But this also
introduced a regression for FVP AArch32 mode but was undetected till now
because the corresponding DTB was not updated. This patch creates a
new `rtsm_ve-motherboard-aarch32.dtsi` which reverts the change and is
now included by the AArch32 DTS files.

Change-Id: Ibefbbf43a91c8fb890f0fa7a22be91f0227dad34
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

In contrast with the non-multi-threading DTS, this enumerates MPIDR
values shifted by one affinity level to the left. The newly added DTS
reflects CPUs with a single thread in them.

Since both DTS files are the same apart from MPIDR contents, the common
bits have been moved to a separate file that's then included from the
top-level DTS files. The multi-threading version only updates the MPIDR
contents.

Change-Id: Id225cd93574f764171df8962ac76f42fcb6bba4b
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

FreeBSD does not understand #interrupt-map in a device tree. This prevents the
GIC from being set up correctly. This patch removes the #interrupt-map in the
device trees for the Base and Foundation FVPs. This enables correct boot of
FreeBSD on these platforms.

These changes have been tested with FreeBSD and an Ubuntu cloud image
(ubuntu-16.04-server-cloudimg-arm64-uefi1.img) to ensure compatibility with
Linux.

Change-Id: I1347acdcf994ec4b1dd843ba32af9951aa54db73
Signed-off-by: Achin Gupta <achin.gupta@arm.com>

Some files have incorrect copyright notices, this patch fixes all
files with deviations from the standard notice.

Change-Id: I66b73e78a50a235acb55f1e2ec2052a42c0570d2
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This patch adds necessary updates for building and running Trusted
Firmware for AArch32 to user-guide.md. The instructions for running
on both `FVP_Base_AEMv8A-AEMv8A` in AArch32 mode and
`FVP_Base_Cortex-A32x4` models are added. The device tree files for
AArch32 Linux kernel are also added in the `fdts` folder.

Change-Id: I0023b6b03e05f32637cb5765fdeda8c8df2d0d3e

The `fvp-base-gicv3-psci` and `fvp-foundation-gicv3-psci` device tree source
files did not have psci node entries for `system off` and `system reset`.
Also the DTS files included `rtsm_ve-motherboard-no_psci.dtsi` instead of
`rtsm_ve-motherboard.dtsi`. As a result, the Linux kernel failed to invoke
the PSCI_SYSTEM_OFF/RESET API when being shutdown/reset. This patch corrects
this problem and also updates the corresponding DTB files.

This patch also removes `rtsm_ve-motherboard-no_psci.dtsi` and
`fvp-foundation-motherboard-no_psci.dtsi` files as they are no longer used.

Change-Id: I8ba61a1323035f7508cae663bb490ac0e8a64618