GitLab

The bl2_early_platform_setup() and bl2_platform_setup() were
redefined for Juno AArch32 eventhough CSS platform layer had
same definition for them. The CSS definitions definitions were
previously restricted to EL3_PAYLOAD_BASE builds and this is now
modified to include the Juno AArch32 builds as well thus
allowing us to remove the duplicate definitions in Juno platform
layer.

Change-Id: Ibd1d8c1428cc1d51ac0ba90f19f5208ff3278ab5
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch does the required changes to enable CSS platforms
to build and use the SDS framework. Since SDS is always coupled with
SCMI protocol, the preexisting SCMI build flag is now renamed to
`CSS_USE_SCMI_SDS_DRIVER` which will enable both SCMI and SDS on
CSS platforms. Also some of the workarounds applied for SCMI are
now removed with SDS in place.

Change-Id: I94e8b93f05e3fe95e475c5501c25bec052588a9c
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Before BL2 loads the SCP ram firmware, `SCP_BOOT_CFG_ADDR` specifies
the primary core.  After the SCP ram firmware has started executing,
`SCP_BOOT_CFG_ADDR` is modified.  This is not normally an issue but
the Juno AArch32 boot flow is a special case.  BL1 does a warm reset
into AArch32 and the core jumps to the `sp_min` entrypoint.  This is
effectively a `RESET_TO_SP_MIN` configuration.  `sp_min` has to be
able to determine the primary core and hence we need to restore
`SCP_BOOT_CFG_ADDR` to the cold boot value before `sp_min` runs.

This magically worked when booting on A53 because the core index was
zero and it just so happened to match with the new value in
`SCP_BOOT_CFG_ADDR`.

Change-Id: I105425c680cf6238948625c1d1017b01d3517c01
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/



Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

Following steps are required to boot JUNO in AArch32 state:
1> BL1, in AArch64 state, loads BL2.
2> BL2, in AArch64 state, initializes DDR.
  Loads SP_MIN & BL33 (AArch32 executable)images.
  Calls RUN_IMAGE SMC to go back to BL1.
3> BL1 writes AArch32 executable opcodes, to load and branch
  at the entrypoint address of SP_MIN, at HI-VECTOR address and
  then request for warm reset in AArch32 state using RMR_EL3.

This patch makes following changes to facilitate above steps:
* Added assembly function to carry out step 3 above.
* Added region in TZC that enables Secure access to the
  HI-VECTOR(0xFFFF0000) address space.
* AArch32 image descriptor is used, in BL2, to load
  SP_MIN and BL33 AArch32 executable images.

A new flag `JUNO_AARCH32_EL3_RUNTIME` is introduced that
controls above changes. By default this flag is disabled.

NOTE: BL1 and BL2 are not supported in AArch32 state for JUNO.

Change-Id: I091d56a0e6d36663e6d9d2bb53c92c672195d1ec
Signed-off-by: Yatharth Kochar <yatharth.kochar@arm.com>
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

This patch adds generic changes in BL1 to support AArch32 state.
New AArch32 specific assembly/C files are introduced and
some files are moved to AArch32/64 specific folders.
BL1 for AArch64 is refactored but functionally identical.
BL1 executes in Secure Monitor mode in AArch32 state.

NOTE: BL1 in AArch32 state ONLY handles BL1_RUN_IMAGE SMC.

Change-Id: I6e2296374c7efbf3cf2aa1a0ce8de0732d8c98a5

This patch support single core to boot to Linux kernel
through Trusted Firmware.
It also support 32 bit kernel and 64 bit kernel booting.

Change-Id: Idc40cc6243e532567ec4334ae37d97c003c90bfa
Signed-off-by: Yi Zheng <yi.zheng@mediatek.com>

Due to the changes in Mediatek platform common code, we need to move
plat related SiP functions to plat folder.

Change-Id: I6b14b988235205a5858b4bf49043bc79d0512b06
Signed-off-by: Jimmy Huang <jimmy.huang@mediatek.com>

* Move TSP platform porting functions to new file:
  include/bl32/tsp/platform_tsp.h.

* Create new TSP_IRQ_SEC_PHY_TIMER definition for use by the generic
  TSP interrupt handling code, instead of depending on the FVP
  specific definition IRQ_SEC_PHY_TIMER.

* Rename TSP platform porting functions from bl32_* to tsp_*, and
  definitions from BL32_* to TSP_*.

* Update generic TSP code to use new platform porting function names
  and definitions.

* Update FVP port accordingly and move all TSP source files to:
  plat/fvp/tsp/.

* Update porting guide with above changes.

Note: THIS CHANGE REQUIRES ALL PLATFORM PORTS OF THE TSP TO
      BE UPDATED

Fixes ARM-software/tf-issues#167

Change-Id: Ic0ff8caf72aebb378d378193d2f017599fc6b78f

Reduce the number of header files included from other header
files as much as possible without splitting the files. Use forward
declarations where possible. This allows removal of some unnecessary
"#ifndef __ASSEMBLY__" statements.

Also, review the .c and .S files for which header files really need
including and reorder the #include statements alphabetically.

Fixes ARM-software/tf-issues#31

Change-Id: Iec92fb976334c77453e010b60bcf56f3be72bd3e

Change-Id: Ic7fb61aabae1d515b9e6baf3dd003807ff42da60

- Add instructions for contributing to ARM Trusted Firmware.

- Update copyright text in all files to acknowledge contributors.

Change-Id: I9311aac81b00c6c167d2f8c889aea403b84450e5