GitLab

RD-N1-Edge based platforms can operate in dual-chip configuration
wherein two rdn1edge SoCs are connected through a high speed coherent
CCIX link.

This patch adds a function to check if the RD-N1-Edge platform is
operating in multi-chip mode by reading the SID register's NODE_ID
value. If operating in multi-chip mode, initialize GIC-600 multi-chip
operation by overriding the default GICR frames with array of GICR
frames and setting the chip 0 as routing table owner.

The address space of the second RD-N1-Edge chip (chip 1) starts from the
address 4TB. So increase the physical and virtual address space size to
43 bits to accommodate the multi-chip configuration. If the multi-chip
mode configuration is detected, dynamically add mmap entry for the
peripherals memory region of the second RD-N1-Edge SoC. This is required
to let the BL31 platform setup stage to configure the devices in the
second chip.

PLATFORM_CORE_COUNT macro is set to be multiple of CSS_SGI_CHIP_COUNT
and topology changes are added to represent the dual-chip configuration.

In order the build the dual-chip platform, CSS_SGI_CHIP_COUNT macro
should be set to 2:
export CROSS_COMPILE=<path-to-cross-compiler>
make PLAT=rdn1edge CSS_SGI_CHIP_COUNT=2 ARCH=aarch64 all

Change-Id: I576cdaf71f0b0e41b9a9181fa4feb7091f8c7bb4
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>

In order to allow the MHUv2 driver to be usable with multiple MHUv2
controllers, use the base address of the controller from the platform
information instead of the MHUV2_BASE_ADDR macro.

Change-Id: I4dbab87b929fb0568935e6c8b339ce67937f8cd1
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

NOTE for platform integrators:
   API `plat_psci_stat_get_residency()` third argument
   `last_cpu_idx` is changed from "signed int" to the
   "unsigned int" type.

Issue / Trouble points
1. cpu_idx is used as mix of `unsigned int` and `signed int` in code
with typecasting at some places leading to coverity issues.

2. Underlying platform API's return cpu_idx as `unsigned int`
and comparison is performed with platform specific defines
`PLAFORM_xxx` which is not consistent

Misra Rule 10.4:
The value of a complex expression of integer type may only be cast to
a type that is narrower and of the same signedness as the underlying
type of the expression.

Based on above points, cpu_idx is kept as `unsigned int` to match
the API's and low-level functions and platform defines are updated
where ever required
Signed-off-by: Deepika Bhavnani <deepika.bhavnani@arm.com>
Change-Id: Ib26fd16e420c35527204b126b9b91e8babcc3a5c

NOTE: AARCH32/AARCH64 macros are now deprecated in favor of __aarch64__.

All common C compilers pre-define the same macros to signal which
architecture the code is being compiled for: __arm__ for AArch32 (or
earlier versions) and __aarch64__ for AArch64. There's no need for TF-A
to define its own custom macros for this. In order to unify code with
the export headers (which use __aarch64__ to avoid another dependency),
let's deprecate the AARCH32 and AARCH64 macros and switch the code base
over to the pre-defined standard macro. (Since it is somewhat
unintuitive that __arm__ only means AArch32, let's standardize on only
using __aarch64__.)

Change-Id: Ic77de4b052297d77f38fc95f95f65a8ee70cf200
Signed-off-by: Julius Werner <jwerner@chromium.org>

N1SDP platform supports RDIMMs with ECC capability. To use the ECC
capability, the entire DDR memory space has to be zeroed out before
enabling the ECC bits in DMC620. Zeroing out several gigabytes of
memory from SCP is quite time consuming so functions are added that
zeros out the DDR memory from application processor which is
much faster compared to SCP. BL33 binary cannot be copied to DDR memory
before enabling ECC so this is also done by TF-A from IOFPGA-DDR3
memory to main DDR4 memory after ECC is enabled.

Original PLAT_PHY_ADDR_SPACE_SIZE was limited to 36-bits with which
the entire DDR space cannot be accessed as DRAM2 starts in base
0x8080000000. So these macros are redefined for all ARM platforms.

Change-Id: If09524fb65b421b7a368b1b9fc52c49f2ddb7846
Signed-off-by: Manoj Kumar <manoj.kumar3@arm.com>

MHU doorbell driver requires arm platform specific
macro "PLAT_CSS_MHU_BASE".
Rename it to "PLAT_MHUV2_BASE", so that platforms other than arm
can use generic MHU doorbell driver.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>

Replace all usage of 'sgiclark' with 'rdn1e1edge' and 'sgiclarka' with
'rdn1edge' as per the updated product names.

Change-Id: Idbc157c73477ec32f507ba2d4a4e907d8813374c
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>