GitLab

At present, the GIC drivers enable Group 0 interrupts only if there are
Secure SPIs listed in the interrupt properties/list. This means that,
even if there are Group 0 SGIs/PPIs configured, the group remained
disabled in the absence of a Group 0 SPI.

Modify both GICv2 and GICv3 SGI/PPI configuration to enable Group 0 when
corresponding SGIs/PPIs are present.

Change-Id: Id123e8aaee0c22b476eebe3800340906d83bbc6d
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

This patch brings in the following fixes:

  - The per-PE target data initialized during power up needs to be
    flushed so as to be visible to other PEs.

  - Setup per-PE target data for the primary PE as well. At present,
    this was only setup for secondary PEs when they were powered on.

Change-Id: Ibe3a57c14864e37b2326dd7ab321a5c7bf80e8af
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The GIC driver initialization currently allows an array of interrupts to
be configured as secure. Future use cases would require more interrupt
configuration other than just security, such as priority.

This patch introduces a new interrupt property array as part of both
GICv2 and GICv3 driver data. The platform can populate the array with
interrupt numbers and respective properties. The corresponding driver
initialization iterates through the array, and applies interrupt
configuration as required.

This capability, and the current way of supplying array (or arrays, in
case of GICv3) of secure interrupts, are however mutually exclusive.
Henceforth, the platform should supply either:

  - A list of interrupts to be mapped as secure (the current way).
    Platforms that do this will continue working as they were. With this
    patch, this scheme is deprecated.

  - A list of interrupt properties (properties include interrupt group).
    Individual interrupt properties are specified via. descriptors of
    type 'interrupt_prop_desc_t', which can be populated with the macro
    INTR_PROP_DESC().

A run time assert checks that the platform doesn't specify both.

Henceforth the old scheme of providing list of secure interrupts is
deprecated. When built with ERROR_DEPRECATED=1, GIC drivers will require
that the interrupt properties are supplied instead of an array of secure
interrupts.

Add a section to firmware design about configuring secure interrupts.

Fixes ARM-software/tf-issues#262

Change-Id: I8eec29e72eb69dbb6bce77879febf32c95376942
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

API documentation updated.

Change-Id: I40feec1fe67a960d035061b54dd55610bc34ce1d
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

API documentation updated.

Change-Id: I14e33cfc7dfa93257c82d76fae186b17a1b6d266
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

SPIs can be routed to either a specific PE, or to any one of all
available PEs.

API documentation updated.

Change-Id: I28675f634568aaf4ea1aa8aa7ebf25b419a963ed
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

API documentation updated.

Change-Id: I129725059299af6cc612bafa8d74817f779d7c4f
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The back end GIC driver converts and assigns the interrupt type to
suitable group.

For GICv2, a build option GICV2_G0_FOR_EL3 is introduced, which
determines to which type Group 0 interrupts maps to.

 - When the build option is set 0 (the default), Group 0 interrupts are
   meant for Secure EL1. This is presently the case.

 - Otherwise, Group 0 interrupts are meant for EL3. This means the SPD
   will have to synchronously hand over the interrupt to Secure EL1.

The query API allows the platform to query whether the platform supports
interrupts of a given type.

API documentation updated.

Change-Id: I60fdb4053ffe0bd006b3b20914914ebd311fc858
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

API documentation updated.

Change-Id: Ib700eb1b8ca65503aeed0ac4ce0e7b934df67ff9
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

API documentation updated.

Change-Id: Ice7511f8df5356851001d2f7dc2a46cfe318f9ba
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

API documentation updated.

Change-Id: I6d61785af0d5330930c709de971a904dc7c3516c
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The PE target mask is used to translate linear PE index (returned by
platform core position) to a bit mask used when targeting interrupts to
a PE, viz. when raising SGIs and routing SPIs.

The platform shall:

  - Populate the driver data with a pointer to array that's to contain
    per-PE target masks.

  - Invoke the new driver API 'gicv2_set_pe_target_mask()' during
    per-CPU initialization so that the driver populates the target mask
    for that CPU.

Platforms that don't intend to target interrupts or raise SGIs need not
populate this.

Change-Id: Ic0db54da86915e9dccd82fff51479bc3c1fdc968
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Document the API in separate platform interrupt controller API document.

Change-Id: If18f208e10a8a243f5c59d226fcf48e985941949
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/



Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

The GIC driver data is initialized by the primary CPU with caches
enabled. When the secondary CPU boots up, it initializes the
GICC/GICR interface with the caches disabled and there is a chance that
the driver data is not yet written back to the memory. This patch fixes
this problem by flushing the driver data after they have been
initialized.

Change-Id: Ie9477029683846209593ff005d2bac559bb8f5e6
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch moves the private GIC common accessors from `gic_common.h` to
a new private header file `gic_common_private.h`. This patch also adds
additional comments to GIC register accessors to highlight the fact
that some of them access register values that correspond to multiple
interrupt IDs. The convention used is that the `set`, `get` and `clr`
accessors access and modify the values corresponding to a single interrupt
ID whereas the `read` and `write` GIC register accessors access the raw
GIC registers and it could correspond to multiple interrupt IDs depending
on the register accessed.

Change-Id: I2643ecb2533f01e3d3219fcedfb5f80c120622f9

The code to set the interrupt priority for secure interrupts in the
new GICv2 and GICv3 drivers is incorrect. The setup code to configure
interrupt priorities of secure interrupts, one interrupt at a time, used
gicd_write_ipriorityr()/gicr_write_ipriority() function affecting
4 interrupts at a time. This bug did not manifest itself because all the
secure interrupts were configured to the highest secure priority(0) during
cold boot and the adjacent non secure interrupt priority would be configured
later by the normal world. This patch introduces new accessors,
gicd_set_ipriorityr() and gicr_set_ipriorityr(), for configuring priority
one interrupt at a time and fixes the the setup code to use the new
accessors.

Fixes ARM-software/tf-issues#344

Change-Id: I470fd74d2b7fce7058b55d83f604be05a27e1341

GICD_IPRIORITYR and GICD_ITARGETSR specifically support byte addressing
so that individual interrupt priorities can be atomically updated by
issuing a single byte write. The previous implementation of
gicd_set_ipriority() and gicd_set_itargetsr() used 32-bit register
accesses, modifying values for 4 interrupts at a time, using a
read-modify-write approach. This potentially may cause concurrent changes
by other CPUs to the adjacent interrupts to be corrupted. This patch fixes
the issue by modifying these accessors to use byte addressing.

Fixes ARM-software/tf-issues#343

Change-Id: Iec28b5f5074045b00dfb8d5f5339b685f9425915

This patch adds a driver for ARM GICv2 systems, example GIC-400. Unlike
the existing GIC driver in `include/drivers/arm/arm_gic.h`, this driver
is optimised for GICv2 and does not support GICv3 systems in GICv2
compatibility mode. The driver interface has been implemented in
`drivers/arm/gic/v2/gicv2_main.c`. The corresponding header is in
`include/drivers/arm/gicv2.h`. Helper functions are implemented in
`drivers/arm/gic/v2/gicv2_helpers.c` and are accessible through the
`drivers/arm/gic/v2/gicv2_private.h` header.

Change-Id: I09fffa4e621fb99ba3c01204839894816cd89a2a