GitLab

In the case of a SP pre-empted by a non-secure interrupt, the SPMC
returns to the SPMD through the FFA_INTERRUPT ABI. It is then forwarded
to the normal world driver hinting the SP has to be resumed after the
non-secure interrupt has been serviced.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I51a694dddcb8ea30fa84e1f11d018bc2abec0a56

As per FF-A v1.0 spec, Table 3.1, messaging method field also contains
information about whether partition supports managed exit or not.
Since a partition can support managed exit only if it supports direct
messaging, so there are two new possible values, managed exit with only
direct messaging or with both messaging methods.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ic77cfb37d70975c3a36c56f8b7348d385735f378

* changes:
  drivers/arm/css/scmi: Update power domain protocol version to 2.0
  tc0: update GICR base address

The SCMI power domain protocol in firmware has been updated to v2.0,
thus update the corresponding version in TF-A too.
Signed-off-by: Nicola Mazzucato <nicola.mazzucato@arm.com>
Change-Id: If3920ff71136dce94b2780e29a47f24aa09876c0

The number of ITS have changed from 4 to 1, resulting
in GICR base address change.
Signed-off-by: Usama Arif <usama.arif@arm.com>
Change-Id: I28101f0d1faf9f3c58591b642033c3fd49a275e7

Updated the documentation with latest Mbed TLS supported
version i.e. Mbed TLS v2.26.0

Fixes available in this version of Mbed TLS mainly affect
key generation/writing and certificates writing, which
are features used in the cert_create tool.

Release notes of Mbed TLSv2.26.0 are available here:
https://github.com/ARMmbed/mbedtls/releases/tag/v2.26.0



Change-Id: Ie15ee45d878b7681e15ec4bf64d54b416a31aa2f
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>

* changes:
  plat:xilinx:versal: Add JTAG DCC support
  plat:xilinx:zynqmp: Add JTAG DCC support
  drivers: dcc: Support JTAG DCC console

NT_FW_CONFIG file is meant to be passed from BL31 to be consumed by
BL33, fvp platforms use this to pass measured boot configuration and
the x0 register is used to pass the base address of it.

In case of hafnium used as hypervisor in normal world, hypervisor
manifest is expected to be passed from BL31 and its base address is
passed in x0 register.

As only one of NT_FW_CONFIG or hypervisor manifest base address can be
passed in x0 register and also measured boot is not required for SPM so
disable passing NT_FW_CONFIG.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ifad9d3658f55ba7d70f468a88997d5272339e53e

* changes:
  plat/st: do not keep mmc_device_info in stack
  plat/intel: do not keep mmc_device_info in stack
  plat/hisilicon: do not keep mmc_device_info in stack

* changes:
  mmc: remove useless extra semicolons
  Revert "mmc:prevent accessing to the released space in case of wrong usage"

Makefile for fiptool already prints verbose line when is (re)building
fiptool, so there is no need to print it also from top level Makefile.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I6936a508702f1bf796d17578bb1f043f06365319

Create a dedicated static struct mmc_device_info mmc_info mmc_info
instead of having this in stack.
A boot issue has been seen on some platform when applying patch [1].

 [1] 13f3c516

 ("mmc:prevent accessing to the released space in case of wrong usage")
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: I73a079715253699d903721c865d6470d58f6bd30

Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: If1d6b2040e482577292890e3554449096648c2ae

Create a dedicated static struct mmc_device_info mmc_info mmc_info
instead of having this in stack.
A boot issue has been seen on some platform when applying patch [1].

 [1] 13f3c516

 ("mmc:prevent accessing to the released space in case of wrong usage")
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: Id52c0be61a30f453a551385883eaf3cbe32b04b9

This reverts commit 13f3c516

.
The STM32MP1 platform can no more boot qwith this change.
The driver will not be aware when the static struct in framework is updated.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: Icc544e243136ee3b0067f316b71dff7dfd6526d6

Create a dedicated static struct mmc_device_info mmc_info mmc_info
instead of having this in stack.
A boot issue has been seen on some platform when applying patch [1].

 [1] 13f3c516

 ("mmc:prevent accessing to the released space in case of wrong usage")
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: If5db8857cccec2e677b16a38eb3eeb41628a264c

Calling 'make clean' in 'all' target is causing recompilation of binary
at every 'make' call, which is wrong.

Also building a new target via 'make TARGET' can cause infinite loop as
it is not defined as explicit make dependency. Dependent targets must be
specified after colon when defining target, which also prevents infinite
loops as make is able to detect these circular dependencies.

Moreover calling 'make clean' is supposed to be done by user when
configuration is changing.

So remove calling 'make clean' in 'all' target and define dependency for
'${PROJECT}' at correct place.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I70e7fd2b04b02f6a0650c82df91d58c9a4cb24d9

* changes:
  drivers: marvell: comphy-a3700: Set TXDCLK_2X_SEL bit during PCIe initialization
  drivers: marvell: comphy-a3700: Set mask parameter for every reg_set call
  drivers: marvell: comphy-a3700: Fix configuring polarity invert bits

* changes:
  plat: imx8mm: Add image load logic for TBBR FIP booting
  plat: imx8mm: Add initial defintions to facilitate FIP layout
  plat: imx8mm: Add image io-storage logic for TBBR FIP booting
  plat: imx8mm: Add imx8mm_private.h to the build

Since there is a secure and non-secure version of the timer registers
there is no need to preserve their context in EL3.
With that, following registers were removed from EL3 save/restore
routine:
	cnthps_ctl_el2
	cnthps_tval_el2
	cnthps_cval_el2
	cnthvs_ctl_el2
	cnthvs_tval_el2
	cnthvs_cval_el2
	cnthp_ctl_el2
	cnthp_cval_el2
	cnthp_tval_el2
	cnthv_ctl_el2
	cnthv_cval_el2
	cnthv_tval_el2
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
Change-Id: I6e2fc09c74a7375c4fccc11f12af4e39e6dc616b

* changes:
  plat/arm/arm_image_load: refine plat_add_sp_images_load_info
  plat/arm/arm_image_load: fix bug of overriding the last node

Marvell Armada 3700 Functional Specifications, section 52.2 PCIe Link
Initialization says that TXDCLK_2X_SEL bit needs to be enabled for PCIe
Root Complex mode. Both U-Boot and Linux kernel support only Root Complex
mode. Set this bit.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: Id2a538c379b911b62597f9463b4842b7b5c24df7

The third argument of the reg_set() function has name 'mask', which
indicates that it is a mask applied to the register value which is
going to be updated. But the implementation of this function uses
this argument to clear prior value of the register, i.e. instead of
  new_val = (old_val & ~mask) | (data & mask);
it does
  new_val = (new_val & ~mask) | data;

(The more proper name for this function should be reg_clrsetbits(),
 since internally it calls mmio_clrsetbits_32().)

To make code more readable set 'mask' argument to real mask, i.e. bits
of register values which are going to be updated.

This patch does not make any functional change, only cosmetic, due to
how 'mask' is interpreted.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: Ifa0339e79c07d1994c7971b65d966b92cb735f65

TXD_INVERT_BIT or RXD_INVERT_BIT needs to be set only in case when
appropriate polarity is inverted. Otherwise these bits should be
cleared.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I8b09fab883a7b995fd72a7d8ae6233f0fa07011b

Refine the function plat_add_sp_images_load_info() by saving the
previous node and only setting its next link when the current node is
valid. This can reduce the check for the next node and simply the
total logic.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: I4061428bf49ef0c3816ac22aaeb2e50315531f88

The traverse flow in function plat_add_sp_images_load_info() will find
the last node in the main load info list, with its
next_load_info==NULL. However this node is still useful and should not
be overridden with SP node info.

The bug will cause below error on RDN2 for spmd enabled:

ERROR:   Invalid NT_FW_CONFIG DTB passed

Fix the bug by only setting the next_load_info of the last node in the
original main node list.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: Icaee5da1f2d53b29fdd6085a8cc507446186fd57

Cortex A77 erratum 1946167 is a Cat B erratum that applies to revisions
<= r1p1. This erratum is avoided by inserting a DMB ST before acquire
atomic instructions without release semantics through a series of
writes to implementation defined system registers.

SDEN can be found here:
https://documentation-service.arm.com/static/600057a29b9c2d1bb22cd1be?token=

Signed-off-by: Lauren Wehrmeister <lauren.wehrmeister@arm.com>
Change-Id: I53e3b4fb7e7575ec83d75c2f132eda5ae0b4f01f

As per the new multi-console framework, updating the JTAG DCC support.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: I77994ce387caf0d695986df3d01d414a920978d0

As per the new multi-console framework, updating the JTAG DCC support.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: I62cfbb57ae7e454fbc91d1c54aafa6e99f9a35c8

The legacy console is gone. Re-add DCC console support based
on the multi-console framework.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: Ia8388721093bc1be3af40974530d7c9a9ae5f43e