GitLab

These source file definitions should be defined in generic
Makefiles so that all platforms can benefit. Ensure that the
symbols are properly marked as weak so they can be overridden
by platforms.

NOTE: This change is a potential compatibility break for
non-upstream platforms.

Change-Id: I7b892efa9f2d6d216931360dc6c436e1d10cffed
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

Replace all use of memset by zeromem when zeroing moderately-sized
structure by applying the following transformation:
memset(x, 0, sizeof(x)) => zeromem(x, sizeof(x))

As the Trusted Firmware is compiled with -ffreestanding, it forbids the
compiler from using __builtin_memset and forces it to generate calls to
the slow memset implementation. Zeromem is a near drop in replacement
for this use case, with a more efficient implementation on both AArch32
and AArch64.

Change-Id: Ia7f3a90e888b96d056881be09f0b4d65b41aa79e
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

We have lots of duplicated defines (and comment blocks too).
Move them to include/plat/common/common_def.h.

While we are here, suffix the end address with _END instead of
_LIMIT.  The _END is a better fit to indicate the linker-derived
real end address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The usage of _LIMIT seems odd here, so rename as follows:
  BL_CODE_LIMIT     --> BL_CODE_END
  BL_RO_DATA_LIMIT  --> BL_RO_DATA_END
  BL1_CODE_LIMIT    --> BL1_CODE_END
  BL1_RO_DATA_LIMIT --> BL1_RO_DATA_END

Basically, we want to use _LIMIT and _END properly as follows:
  *_SIZE + *_MAX_SIZE = *_LIMIT
  *_SIZE + *_SIZE     = *_END

The _LIMIT is generally defined by platform_def.h to indicate the
platform-dependent memory constraint.  So, its typical usage is
  ASSERT(. <= BL31_LIMIT, "BL31 image has exceeded its limit.")
in a linker script.

On the other hand, _END is used to indicate the end address of the
compiled image, i.e. we do not know it until the image is linked.

Here, all of these macros belong to the latter, so should be
suffixed with _END.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Commit 0029624f

 ("Add
PLAT_xxx_ADDR_SPACE_SIZE definition") deprecates 'ADDR_SPACE_SIZE' in
favor of PLAT_(PHY|VIRT)_ADDRESS_SPACE_SIZE. Migrate the zynqmp platform
to use the new interface.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>

The platform.mk sets build options required for ZynqMP, but users
can still change them from the command line, like:

  make PLAT=zynqmp RESET_TO_BL31=0 CROSS_COMPILE=...

Then, the makefile shows an error message in that case:
  Using BL31 as the reset vector is only one option supported on ZynqMP.
  Please set RESET_TO_BL31 to 1.

If the option is not user-configurable, the makefile can specify
"override" to prevent users from changing it.  We do not need the
error message for the case that never happens.

Likewise, ENABLE_PLAT_COMPAT := 0 and PROGRAMMABLE_RESET_ADDRESS := 1
are mandatory to avoid build error.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>

Some files have incorrect copyright notices, this patch fixes all
files with deviations from the standard notice.

Change-Id: I66b73e78a50a235acb55f1e2ec2052a42c0570d2
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

There are many instances in ARM Trusted Firmware where control is
transferred to functions from which return isn't expected. Such jumps
are made using 'bl' instruction to provide the callee with the location
from which it was jumped to. Additionally, debuggers infer the caller by
examining where 'lr' register points to. If a 'bl' of the nature
described above falls at the end of an assembly function, 'lr' will be
left pointing to a location outside of the function range. This misleads
the debugger back trace.

This patch defines a 'no_ret' macro to be used when jumping to functions
from which return isn't expected. The macro ensures to use 'bl'
instruction for the jump, and also, for debug builds, places a 'nop'
instruction immediately thereafter (unless instructed otherwise) so as
to leave 'lr' pointing within the function range.

Change-Id: Ib34c69fc09197cfd57bc06e147cc8252910e01b0
Co-authored-by: Douglas Raillard <douglas.raillard@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The callback IRQ is delivered to the NS OS. Provide an interface to
allow the NS OS to obtain the callback data from the secure HW.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>

The IPI hardware is secure and managed by ATF, nevertheless we deliver
the IRQ to the rich OS. The IRQ is needed to receive PM callbacks.
Enable the IPI interrupt when the rich OS probes the API version.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>

Remove dead code pieces and stale comments.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>

Cc: Michal Simek <michal.simek@xilinx.com>
Reported-by: Jonas Karlsson <jonas.karlsson@atero.se>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>

Use the PMUFW get_chipid call to obtain IDCODE and version register.

Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>

Allow reading more than just a single value from the message buffer.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>

On ZynqMP the FSBL will configure the system counter. Hence, remove the
initialization of the system counter with hardcoded values from the ATF
and use the setup provided by the bootloader.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>

The silicon ID does not change at runtime. Skip the IO access if the
ID has been read before.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>

We must guarantee that writes have become effective before returning to
the caller. Hence, wait for PMUFW signaling completion of the FW call
before returning to the rich OS.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>

Add support to provide silicon id to non-secure
software through SMC.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>

[ sb
Move zynqmp_get_silicon_id outside of compile guards to avoid build
errors.
]
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>

This patch adds pm_fpga_load() and pm_fpga_get_status() API's to provide
the Access to the xilfpga library to load the bitstream into zynqmp
PL region.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>

This patch adds a new pm ID to sync with PMUFW ID numbers.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>

During system suspend, identify slaves which are configured
as wake sources and call pm_set_wakeup_source API for each of them.

Identifying if device may wake the system is done by checking if any
interrupt of that device is enabled in GICD_ISENABLER when the APU is
about to enter SUSPEND_TO_RAM state. If such interrupt is found,
pm_set_wakeup_source is called with corresponding PM node ID as
argument.
Signed-off-by: Filip Drazic <filip.drazic@aggios.com>

Signed-off-by: Filip Drazic <filip.drazic@aggios.com>

The state argument of the pm_self_suspend API encodes the state to
which the APU intends to suspend. The state can be:
- PM_APU_STATE_CPU_IDLE - processor power down, all memories remain
  on
- PM_APU_STATE_SUSPEND_TO_RAM - all processors powered down, L2$
  powered down, all OCM banks in retention and DDR in
  self-refresh.
The calls for setting requirements for L2$ and OCM banks are now
redundant and removed.
Signed-off-by: Filip Drazic <filip.drazic@aggios.com>
[ sb
 - remove redundant #defines
]
Signed-off-by: Sören Brinkmann <soren.brinkmann@xilinx.com>

Implementation is based on arm_validate_power_state().
This function is called during CPU_SUSPEND PSCI call to validate
power_state parameter. If state is valid this function populate it
in req_state array as power domain level specific local state.
ATF platform migration guide chapter 2.2 defines this function as
mandatory for PSCIv1.0 CPU_SUSPEND support.
Signed-off-by: Stefan Krsmanovic <stefan.krsmanovic@aggios.com>

When moving the ATF into the DRAM address space an additional
translation table is required.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>

The OCM space was reorganized to use the space more efficiently. Adjust
the default ATF location to be aligned with other ZynqMP software
components.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>

Arm provided error injection support. To enable this error injection,
we need to set L2DEIEN in L2ACTLR_EL1 register and L1DEIEN in
CPUACTLR_EL1 register.

This is needed for our cortexa53 edac linux driver testing.
These registers need write access from non secure EL1 i.e linux
at the time of setting the above bits.
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>

ZynqMP only supports builds with RESET_TO_BL31=1. Set this option
through the platform makefile on default.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>

Nodes represent IPI dedicated to the RPU (not accessible by APU)
Signed-off-by: Mirela Simonovic <mirela.simonovic@aggios.com>

Initialize the generic_delay_timer in the zynqmp port.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>

This patch migrates the upstream platform makefiles to include the
console drivers from the new location in ARM Trusted Firmware code
base.

Change-Id: I866d6c4951e475de1f836ce8a8c1d5e6da9577e3

This patch moves the `arm_common.c` file from `plat/arm/common/aarch64/`
to the parent directory since the functions implemented in the file are
not AArch64 specific. The platform makefiles are also modified for this
change.

Change-Id: I776d2e4958f59041476cf2f53a9adb5b2d304ee0

The `plat_psci_common.c` was moved to the new location `plat/common`
and a stub file was retained at previous location for compatibility. This
patch modifies the platform makefiles to include the file from the new
location.

Change-Id: Iabddeeb824e9a5d72d176d7c644735966c8c0699

Set the SEPARATE_CODE_AND_RODATA build flag to map read-only data as
execute never.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>

The arm_setup_page_tables() function used to expect a single set of
addresses defining the extents of the whole read-only section, code
and read-only data mixed up, which was mapped as executable.

This patch changes this behaviour. arm_setup_page_tables() now
expects 2 separate sets of addresses:

 - the extents of the code section;
 - the extents of the read-only data section.

The code is mapped as executable, whereas the data is mapped as
execute-never. New #defines have been introduced to identify the
extents of the code and the read-only data section. Given that
all BL images except BL1 share the same memory layout and linker
script structure, these #defines are common across these images.
The slight memory layout differences in BL1 have been handled by
providing values specific to BL1.

Note that this patch also affects the Xilinx platform port, which
uses the arm_setup_page_tables() function. It has been updated
accordingly, such that the memory mappings on this platform are
unchanged. This is achieved by passing null values as the extents
of the read-only data section so that it is ignored. As a result,
the whole read-only section is still mapped as executable.

Fixes ARM-software/tf-issues#85

Change-Id: I1f95865c53ce6e253a01286ff56e0aa1161abac5

This patch introduces a new header file: include/lib/utils.h.
Its purpose is to provide generic macros and helper functions that
are independent of any BL image, architecture, platform and even
not specific to Trusted Firmware.

For now, it contains only 2 macros: ARRAY_SIZE() and
IS_POWER_OF_TWO(). These were previously defined in bl_common.h and
xlat_tables.c respectively.

bl_common.h includes utils.h to retain compatibility for platforms
that relied on bl_common.h for the ARRAY_SIZE() macro. Upstream
platform ports that use this macro have been updated to include
utils.h.

Change-Id: I960450f54134f25d1710bfbdc4184f12c049a9a9

This patch introduces the arm_setup_page_tables() function to
set up page tables on ARM platforms. It replaces the
arm_configure_mmu_elx() functions and does the same thing except
that it doesn't enable the MMU at the end. The idea is to reduce
the amount of per-EL code that is generated by the C preprocessor
by splitting the memory regions definitions and page tables creation
(which is generic) from the MMU enablement (which is the only per-EL
configuration).

As a consequence, the call to the enable_mmu_elx() function has been
moved up into the plat_arch_setup() hook. Any other ARM standard
platforms that use the functions `arm_configure_mmu_elx()` must be
updated.

Change-Id: I6f12a20ce4e5187b3849a8574aac841a136de83d

Add build time option 'cadence1' for ZYNQMP_CONSOLE to select the 2nd
UART available in the SoC.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>