GitLab

We previously left our caches on during power-down to prevent any
non-caching accesses to memory that is cached by other cores. Now with
the last accessed areas all being marked as non-cached by
USE_COHERENT_MEM we can rely on that to workaround our interconnect
issues. Remove the old workaround.

Change-Id: Idadb7696d1449499d1edff4f6f62ab3b99d1efb7
Signed-off-by: Andrew F. Davis <afd@ti.com>

HW_ASSISTED_COHERENCY implies something stronger than just hardware
coherent interconnect, specifically a DynamIQ capable ARM core.

For K3, lets use WARMBOOT_ENABLE_DCACHE_EARLY to enable caches early
and then let the caches get shut off on powerdown, to prevent data
corruption we also need to USE_COHERENT_MEM so that any accesses to
shared memory after this point is only to memory that is set as
non-cached for all cores.

Change-Id: Ib9337f012df0e0388237942607c501b6f3e2a949
Signed-off-by: Andrew F. Davis <afd@ti.com>

In the rockchip bl31 setup the __RO_START__ and __RO_END__ symbols are
currently imported into special BL31_RO_* constants while the general
code also imports them as BL_CODE_BASE and BL_CODE_END.

So we can just use the general symbols and can drop the duplication.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Change-Id: Ibf1b48ad80bed897247a1690a32711030479262d

The Cortex-A72 based cores on K3 platforms can be clocked fast
enough that an extra latency cycle is needed to ensure correct
L2 access. Set the latency here for all A72 cores.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Change-Id: Id534316dec1c1f326908efbfd964f219cda7386a

Enable Cortex-A72 support for J721E.

Change-Id: I5bea5fb6ec45d1a9f8f2192d42da2cc03ae0f7ec
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>

AIPSTZ provide access control for all the peripherals connected
to it. In this patch all the perperals are configured accessible
to all the master. it can be customized based the actual use
case.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Change-Id: I5ef5baa1da6906f13a60923d27ede336c61e319a

Platform defines are already provided by the build system so let's not
duplicate them.

Change-Id: Icf1ea76c3c3213e27b447c95e2b22b961fa7693e
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>

The manual documents that 0x3036006c should contains the soc revision
for imx8mq but this always reports A0. Work around this by parsing the
ROM header and checking if OCOTP register 0x40 is stuck at 0xff0055aa.

Determining this inside TF-A makes life easier for OS, see for example
this linux discussion: https://lkml.org/lkml/2019/5/3/465



The soc revision can also be useful inside TF-A itself, for example for
the non-upstream DDR DVFS "busfreq" feature is affected by 8mq erratas.

The clock for OCOTP block can be disabled by OS so only initialize soc
revision once at boot time.

Change-Id: I9ca3f27840229ce8a28b53870e44da29f63c73aa
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>

Remove an assert() that assumes a specific value being passed from
BL2.  This value is dependent on BL2 version, so makes this assert()
not portable.
Suggested-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Change-Id: Ife3d934b2fa37fc1c66963dd4eb1afe2ca17d740

N1SDP exhibits the behavior similar to Juno wherein CNTBaseN.CNTFRQ
can be written but does not reflect the value of the CNTFRQ register
in CNTCTLBase frame. This doesn't follow ARM ARM in that the value
updated in CNTCTLBase.CNTFRQ is not reflected in CNTBaseN.CNTFRQ.

Hence enable the workaround (applied to Juno) for N1SDP that updates
the CNTFRQ register in the Non Secure CNTBaseN frame.

Change-Id: Id89ee1bca0f25c9d62f8f794f2c4f4e618cdf092
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>

The default DRAM2 start address for Arm platforms
is 0x880000000. However, for N1SDP platform this is
0x8080000000.

Fix the DRAM2 start address by initialising
PLAT_ARM_DRAM2_BASE.

Without this fix there is a mismatch of the System
memory region view as seen by the BL31 runtime
firmware (PSCI) versus the view of the OS (which
is based on the description provided by UEFI. In
this case UEFI is correctly describing the DRAM2
start address).

This implicates in secondary cores failing to start
on some Operating Systems if the OS decides to place
the secondary start address in the mismatched region.

Change-Id: I57220e753219353dda429868b4c5e1a69944cc64
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>

The default DRAM2 base address for Arm platforms
is 0x880000000. However, on some platforms the
firmware may want to move the start address to
a different value.

To support this introduce PLAT_ARM_DRAM2_BASE that
defaults to 0x880000000; but can be overridden by
a platform (e.g. in platform_def.h).

Change-Id: I0d81195e06070bc98f376444b48ada2db1666e28
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>

Remove duplicated linker symbols, resue the symbols
defined in bl_common.h

Change-Id: I10de450eccc78c09b61a8ae7126bf4f4029fa682
Signed-off-by: Jacky Bai <ping.bai@nxp.com>

For security DMA should be blocked at the SMMU by default
unless explicitly enabled for a device. SMMU is disabled
after reset with all streams bypassing the SMMU, and
abortion of all incoming transactions implements a default
deny policy on reset.
This patch also moves "bl1_platform_setup()" function from
arm_bl1_setup.c to FVP platforms' fvp_bl1_setup.c and
fvp_ve_bl1_setup.c files.

Change-Id: Ie0ffedc10219b1b884eb8af625bd4b6753749b1a
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

- Add basic platform setup
- Add generic CPU helper functions
- Add delay timer platform implementation
- Use TI 16550 uart driver

Change-Id: I1c29569c68fe9fca5e10e88a22a29690bab7141f
Signed-off-by: kenny liang <kenny.liang@mediatek.com>

The IMX_SIP_BUILDINFO call was implemented for imx8qm and imx8qx but
it's also applicable to imx8m.

This fixes U-Boot not printing commit hash on 8m with upstream TF-A.

Change-Id: Idcfd9729eaaccf329c24e241da325f1f6cd3c880
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>

Only IRQ 32 (SPI 0) needs to be kept unmasked, not everything divisible
by 32.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Change-Id: I286b925eead89218cfeddd82f53a634f3447d212

This is similar to imx8mm and allows uboot to run fastboot over USB otg.

There is a different set of power domains on 8mq but same bits covers
all off them.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Change-Id: I1151c2bc2d32b1e02b4db16285b3d30cabc0d64d

This patch fixes this issue:
https://github.com/ARM-software/tf-issues/issues/660



The introduced changes are the following:

1) Some cores implement cache coherency maintenance operation on the
hardware level. For those cores, such as - but not only - the DynamIQ
cores, it is mandatory that TF-A is compiled with the
HW_ASSISTED_COHERENCY flag. If not, the core behaviour at runtime is
unpredictable. To prevent this, compile time checks have been added and
compilation errors are generated, if needed.

2) To enable this change for FVP, a logical separation has been done for
the core libraries. A system cannot contain cores of both groups, i.e.
cores that manage coherency on hardware and cores that don't do it. As
such, depending on the HW_ASSISTED_COHERENCY flag, FVP includes the
libraries only of the relevant cores.

3) The neoverse_e1.S file has been added to the FVP sources.

Change-Id: I787d15819b2add4ec0d238249e04bf0497dc12f3
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

This patch is a preparation for the subsequent changes in
SMMUv3 driver. It introduces a new "smmuv3_poll" function
and replaces inline functions for accessing SMMU registers
with mmio read/write operations. Also the infinite loop
for the poll has been replaced with a counter based timeout.

Change-Id: I7a0547beb1509601f253e126b1a7a6ab3b0307e7
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

All supported Rockchip SoCs (RK3288, RK3328, RK3368 and RK3399)
have non-continuous memory areas in the linker script with a huge
gap between them. This results in extremely padded binary images
with a size of about 4 GiB.

E.g. on the RK3399 we have the following memory areas (and base addresses):
RAM (0x1000), SRAM (0xFF8C0000), and PMUSRAM (0xFF3B0000).

Consumers of the TF-A project (e.g. coreboot or U-Boot) therefore
use the ELF image instead, which has a size of a few hundred kBs.

In order to prevent the generation of a huge and useless file,
this patch disables the binary generation for all affected Rockchip
SoCs.
Signed-off-by: Christoph Müllner <christophm30@gmail.com>
Change-Id: I4ac65bdf1e598c3e1a59507897d183aee9a36916

Currently the compile-time constant PLAT_RK_UART_BASE defines
which UART is used as console device. E.g. on RK3399 it is set
to UART2. That means, that a single bl31 image can not be used
for two boards, which just differ on the UART console.

This patch addresses this limitation by parsing the "stdout-path"
property from the "chosen" node in the DTB. The expected property
string is expected to have the form "serialN:XXX", with
N being either 0, 1, 2, 3 or 4. When the property is found, it will
be used to override PLAT_RK_UART_BASE.

Tested on RK3399-Q7, with a stdout-path of "serial0:115200n8".
Signed-off-by: Christoph Müllner <christophm30@gmail.com>
Change-Id: Iafe1320e77ab006c121f8d52745d54cef68a48c7

params_setup.c provides the function params_early_setup, which
takes care of parsing ATF parameters (bl31_plat_param array,
fdt or coreboot table). As params_early_setup is defined as weak
symbol in bl31_plat_setup.c, providing a platform-specific
bl31_plat_setup implementation is optional.

This patch adds the rockchip-common params_setup.c to the sources
for RK3328. This streamlines the parameter handling for all supported
rockchip SoCs.
Signed-off-by: Christoph Müllner <christophm30@gmail.com>
Change-Id: I071c03106114364ad2fc408e49cc791fe5b35925

In order to set the UART base during bootup in common code of
plat/rockchip, we need to streamline the way the UART base addresses
are defined and add the missing definitions and mappings.

This patch does so by following the pattern UARTn_BASE, which is
already in use on RK3399 and RK3328. The numbering itself is derived
from the upstream Linux DTS files of the individual SoCs.
Signed-off-by: Christoph Müllner <christophm30@gmail.com>
Change-Id: I341a1996f4ceed5f82a2f6687d4dead9d7cc5c1f

Security sources are required if stack-protector is enabled.

Change-Id: Ia0071f60cf03d48b200fd1facbe50bd9e2f8f282
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

The MSMC port defines were added to help in the case when some ports
are not connected and have no cores attached. We can get the same
functionality by defined the number of cores on that port to zero.
This simplifies several code paths, do this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Change-Id: I3247fe37af7b86c3227e647b4f617fab70c8ee8a

While mainline u-boot always expects to submit the devicetree
as platform param, coreboot always uses the existing parameter
structure. As libfdt is somewhat big, it makes sense to limit
its inclusion to where necessary and thus only to non-coreboot
builds.

libfdt itself will get build in all cases, but only the non-
coreboot build will actually reference and thus include it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Change-Id: I4c5bc28405a14e6070917e48a526bfe77bab2fb7

These sections of code are only needed for the coherency workaround
used for AM65x, if this workaround is not needed then this code
is not either. Mark it off to keep it separated from the rest of
the PSCI implementation.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Change-Id: I113ca6a2a1f7881814ab0a64e5bac57139bc03ef

To make the USE_COHERENT_MEM option work we need to add an entry for the
area to our memory map table. Also fixup the alignment here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Change-Id: I1c05477a97646ac73846a711bc38d3746628d847

The size of the RO data area was calculated by subtracting the area end
address from itself and not the base address due to a typo. Fix this
here.

Note, this was noticed at a glance thanks to the new aligned formating
of this table.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Change-Id: I994022ac9fc95dc5e37a420714da76081c61cce7

This macro was used when many of these functions were stubbed out,
the macro is not used anymore, remove it.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Change-Id: Ida33f92fe3810a89e6e51faf6e93c1d2ada1a2ee

Change-Id: I54869151bfc434df66933bd418c70cca9c3d0861
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>

The rk3288 is a 4-core Cortex-A12 SoC and shares a lot of features
with later SoCs.

Working features are general non-secure mode (the gic needs special
love for that), psci-based smp bringing cpu cores online and also
taking them offline again, psci-based suspend (the simpler variant
also included in the linux kernel, deeper suspend following later)
and I was also already able to test HYP-mode and was able to boot
a virtual kernel using kvm.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Change-Id: Ibaaa583b2e78197591a91d254339706fe732476a

There are a number or ARMv7 Rockchip SoCs that are very similar in their
bringup routines to the existing arm64 SoCs, so there is quite a high
commonality possible here.

Things like virtualization also need psci and hyp-mode and instead of
trying to cram this into bootloaders like u-boot, barebox or coreboot
(all used in the field), re-use the existing infrastructure in TF-A
for this (both Rockchip plat support and armv7 support in general).

So add core support for aarch32 Rockchip SoCs, with actual soc support
following in a separate patch.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Change-Id: I298453985b5d8434934fc0c742fda719e994ba0b

The cpuson_entry_point and cpuson_flags are already declared in
plat_private.h so there is no need to have it again declared in
the local pmu.h, especially as it may cause conflicts when the
other type changes.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Change-Id: I80ae0e23d22f67109ed96f8ac059973b6de2ce87

Some older socs like the rk3288 do not have the necessary registers
to check the wfi/wfe state of the cpu cores. Allow this case an "just"
do an additional delay similar to how the Linux kernel handles smp
right now.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Change-Id: I0f67af388b06b8bfb4a9bac411b4900ac266a77a

The current code doing power-management from sram is highly
arm64-specific so should live in a corresponding subdirectory
and not in the common area.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Change-Id: I3b79ac26f70fd189d4d930faa6251439a644c5d9

GCC complains for quite some versions, when compiling the M0 firmware
for Rockchip's rk3399 platform, about an invalid type of function 'main':

  warning: return type of 'main' is not 'int' [-Wmain]

This patch addresses this, by renaming the function to 'm0_main'.
Signed-off-by: Christoph Müllner <christophm30@gmail.com>
Change-Id: I10887f2bda6bdb48c5017044c264139004f7c785

Change-Id: Ie649b3c367a93db057eeaee7e83fa3e43f8c2607
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>

When we get a sequence ID that does not match what we expect then the we
are looking at is not the one we are expecting and so we error out. We
can also assume this message is a stale message left in the queue, in
this case we can read in the next message and check again for our
message. Switch to doing that here. We only retry a set number of times
so we don't lock the system if our message is actually lost and will
never show up.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Change-Id: I6c8186ccc45e646d3ba9d431f7d4c451dcd70c5c