GitLab

This patch enables choice of RSA version at run time to be used for
generating signatures by the cert_tool. The RSA PSS as defined in
PKCS#1 v2.1 becomes the default version and this patch enables to specify
the RSA PKCS#1 v1.5 algorithm to `cert_create` through the command line
-a option. Also, the build option `KEY_ALG` can be used to pass this
option from the build system. Please note that RSA PSS is mandated
by Trusted Board Boot requirements (TBBR) and legacy RSA support is
being added for compatibility reasons.

Fixes ARM-Software/tf-issues#499
Change-Id: Ifaa3f2f7c9b43f3d7b3effe2cde76bf6745a5d73
Co-Authored-By: Eleanor Bonnici <Eleanor.bonnici@arm.com>
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

The `KEY_ALG` variable is used to select the algorithm for key
generation by `cert_create` tool for signing the certificates. This
variable was previously undocumented and did not have a global default
value. This patch corrects this and also adds changes to derive the
value of `TF_MBEDTLS_KEY_ALG` based on `KEY_ALG` if it not set by the
platform. The corresponding assignment of these variables are also now
removed from the `arm_common.mk` makefile.
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Change-Id: I78e2d6f4fc04ed5ad35ce2266118afb63127a5a4

The internal synchronisation timings of the FVP model version
11.0 build 11.0.34 and version 8.5 build 0.8.5202 has been
changed compared to older version of the models.

This change may have an impact on how the model behaves depending
on the workload being run on the model. For example test failures
have been seen where the primary core has powered on a secondary
core but was then starved of host CPU time and so was not able to
update power status, resulting a test failure due to an incorrect
status. This, or similar behaviour, is not to be expected from
real hardware platforms.

This patch adds a usage note on how to launch these models so
that internal synchronisation timing matches that of the older
version of the models, specifically adding the -Q 100 option.

Change-Id: If922afddba1581b7246ec889b3f1598533ea1b7e
Signed-off-by: David Cunado <david.cunado@arm.com>

Add support for a minimal secure interrupt service in sp_min for
the AArch32 implementation. Hard code that only FIQs are handled.

Introduce bolean build directive SP_MIN_WITH_SECURE_FIQ to enable
FIQ handling from SP_MIN.

Configure SCR[FIQ] and SCR[FW] from generic code for both cold and
warm boots to handle FIQ in secure state from monitor.

Since SP_MIN architecture, FIQ are always trapped when system executes
in non secure state. Hence discard relay of the secure/non-secure
state in the FIQ handler.

Change-Id: I1f7d1dc7b21f6f90011b7f3fcd921e455592f5e7
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

Since Trusted OS firmware may have extra images, need to
assign new uuid and image id for them.
The TBBR chain of trust has been extended to add support
for the new images within the existing Trusted OS firmware
content certificate.

Change-Id: I678dac7ba1137e85c5779b05e0c4331134c10e06
Signed-off-by: Summer Qin <summer.qin@arm.com>

The documentation describes the design of the translation tables
library version 2 used by the ARM Trusted Firmware.

The diagram file has been created with Dia version 0.97.2. This tool
can be obtained from: https://wiki.gnome.org/Apps/Dia/Download



Inkscape has been used to generate the *.png file from the *.dia file
to work around a bug in the generation of *.png files in some versions
of Dia.

Change-Id: Ie67d9998d4ae881b2c060200a318ad3ac2fa5e91
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

The current build system and driver requires the CCI product to be
specified at build time. The device constraints can be determined at run
time from its ID registers, obviating the need for specifying them
ahead.

This patch adds changes to identify and validate CCI at run time. Some
global variables are renamed to be in line with the rest of the code
base.

The build option ARM_CCI_PRODUCT_ID is now removed, and user guide is
updated.

Change-Id: Ibb765e349d3bc95ff3eb9a64bde1207ab710a93d
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

ARM CPUs with multi-threading implementation has more than one
Processing Element in a single physical CPU. Such an implementation will
reflect the following changes in the MPIDR register:

  - The MT bit set;

  - Affinity levels pertaining to cluster and CPUs occupy one level
    higher than in a single-threaded implementation, and the lowest
    affinity level pertains to hardware threads. MPIDR affinity level
    fields essentially appear shifted to left than otherwise.

The FVP port henceforth assumes that both properties above to be
concomitant on a given FVP platform.

To accommodate for varied MPIDR formats at run time, this patch
re-implements the FVP platform-specific functions that translates MPIDR
values to a linear indices, along with required validation. The same
treatment is applied for GICv3 MPIDR hashing function as well.

An FVP-specific build option FVP_MAX_PE_PER_CPU is introduced which
specifies the maximum number of threads implemented per CPU. For
backwards compatibility, its value defaults to 1.

Change-Id: I729b00d3e121d16ce9a03de4f9db36dfac580e3f
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Commit d832aee9

, which added SPE support, got the alphabetical ordering
wrong for documentation and Makefile addition. This patch fixes that.

Change-Id: I061ecfba4db363902c9d7d577d2ce6c612cb9e1d
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Change-Id: I0cd355d9fc7f14fb4eabb443d596d6f0858f609e
Signed-off-by: Eleanor Bonnici <Eleanor.bonnici@arm.com>

ARM TF has been tested against Linaro Release 17.04 - the Linaro
binaries have been update and also the version of the compiler.

Linaro binaries: 17.01 --> 17.04
AArch64 & AArch32 compilers: 5.3-2015.05 (gcc 5.3) -> 6.2-2016.11 (gcc 6.2)

This patch updates the User Guide is to state that Linaro
release 17.04 is supported.

Additionally, the following fixes are made to the User Guide:
- Removed out of date reference to Linaro release 16.06.
- Updated the Juno variant coverage to include r2.

Change-Id: Iebbced3356f8c6b3c2bff2df62574db9f937ca7b
Signed-off-by: David Cunado <david.cunado@arm.com>

Trusted Firmware has been tested as part of its CI system against Cortex
and Foundation models in the 11.0 Model release available on
developer.arm.com. Trusted Firmware has also been tested against the v8.5
AEM model.

This patch updates the user guide documentation to reflect the version of
the Foundation, AEM and Cortex Models that Trusted Firmware has been
tested against.

Change-Id: I3b5b4d1e4220bda1dcc88aa9cfa01fa711ed92cd
Signed-off-by: David Cunado <david.cunado@arm.com>

Non-automated fixes to the converted documentation.

Change-Id: I61f3d37c7a8d6a56a7351048060b970c5b3751e4
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

Due to recent issues in the rendering of the documentation on GitHub and
some long-standing issues like the lack of automatic table of content in
Markdown, the documentation has been converted to reStructuredText.
Basic constructs looks pretty similar to Markdown.

Automatically convert GitHub markdown documentation to reStructuredText
using pandoc.

Change-Id: If20b695acedc6d1b49c8d9fb64efd6b6ba23f4a9
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>