GitLab

It is desired to have the peripheral writes completed to clear the
interrupt condition and de-assert the interrupt request to GIC before
EOI write. Failing which spurious interrupt will occurred.

A barrier is needed to ensure peripheral register write transfers are
complete before EOI is done.

GICv2 memory mapped DEVICE nGnR(n)E writes are ordered from core point
of view. However these writes may pass over different interconnects,
bridges, buffers leaving some rare chances for the actual write to
complete out of order.

GICv3 ICC EOI system register writes have no ordering against nGnR(n)E
memory writes as they are over different interfaces.

Hence a dsb can ensure from core no writes are issued before the previous
writes are *complete*.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Change-Id: Ie6362009e2f91955be99dca8ece14ade7b4811d6

This patch provides the platform level support to enable GICv3
drivers on future Tegra platforms.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I966a4502b2a4a7bd1ce66da843997c9ed605c59f

* changes:
  ddr: a80x0: add DDR 32-bit ECC mode support
  ble: ap807: improve PLL configuration sequence
  ble: ap807: clean-up PLL configuration sequence
  ddr: a80x0: add DDR 32-bit mode support
  plat: marvell: mci: perform mci link tuning for all mci interfaces
  plat: marvell: mci: use more meaningful name for mci link tuning
  plat: marvell: a8k: remove wrong or unnecessary comments
  plat: marvell: ap807: enable snoop filter for ap807
  plat: marvell: ap807: update configuration space of each CP
  plat: marvell: ap807: use correct address for MCIx4 register
  plat: marvell: add support for PLL 2.2GHz mode
  plat: marvell: armada: make a8k_common.mk and mss_common.mk more generic
  marvell: armada: add extra level in marvell platform hierarchy

Load address of tb_fw_config is incorrectly mentioned
in below device trees:
1. rdn1edge_fw_config.dts
2. tc0_fw_config.dts

Till now, tb_fw_config load-address is not being retrieved from
device tree and hence never exeprienced any issue for tc0 and
rdn1edge platform.

For tc0 and rdn1edge platform, Load-address of tb_fw_config should
be the SRAM base address + 0x300 (size of fw_config device tree)
Hence updated these platform's fw_config.dts accordingly to reflect
this load address change.

Change-Id: I2ef8b05d49be10767db31384329f516df11ca817
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>

* changes:
  Tegra194: ras: verbose prints for SErrors
  Prevent RAS register access from lower ELs
  Tegra194: SiP: clear RAS corrected error records
  Tegra194: add RAS exception handling

* changes:
  tbbr: add chain of trust for Secure Partitions
  cert_create: extend Secure partition support for tbbr CoT

Change-Id: I3726f42f8f3de0cd88bd77a0f9d92a710649d18c
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

with sha 44f1aa8e

, support for Silicon Provider(SiP) owned Secure
Partition(SP) was added for dualroot CoT. This patch extends this
support for tbbr CoT.

Earlier tbbr CoT for SPs was left to avoid adding new image types in
TBBR which could possibly be seen as deviation from specification.
But with further discussions it is understood that TBBR being a
*minimal* set of requirements that can be extended as long as we don't
violate any of the musts, which is the case with adding SP support.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I1b9e3ebdd7d653f1fd4cc3bd910a69871b55ecbb

This patch provides verbose prints for RAS SErrors handled by the
firmware, for improved debugging.

Change-Id: Iaad8d183054d884f606dc4621da2cc6b2375bcf9
Signed-off-by: David Pu <dpu@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds a build config 'RAS_TRAP_LOWER_EL_ERR_ACCESS' to set
SCR_EL3.TERR during CPU boot. This bit enables trapping RAS register
accesses from EL1 or EL2 to EL3.

RAS_TRAP_LOWER_EL_ERR_ACCESS is disabled by default.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: Ifb0fb0afedea7dd2a29a0b0491a1161ecd241438

This patch introduces a function ID to clear all the RAS error
records for corrected errors.

Per latest requirement, ARM RAS corrected errors will be reported to
lower ELs via interrupts and cleared via SMC. This patch provides
required function to clear RAS error status.

This patch also sets up all required RAS Corrected errors in order to
route RAS corrected errors to lower ELs.

Change-Id: I554ba1d0797b736835aa27824782703682c91e51
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Signed-off-by: David Pu <dpu@nvidia.com>

This patch adds all Tegra194 RAS nodes definitions and support to
handle all uncorrectable RAS errors.

Change-Id: I109b5a8dbca91d92752dc282c4ca30f273c475f9
Signed-off-by: David Pu <dpu@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

with sha 0792dd7d

, support to generate certificate for Secure
Partitions was added for dualroot CoT only, this patch extends
this support for tbbr CoT.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I451c0333536dd1cbe17861d454bdb0dc7a17c63f

The RK3368 has two clusters of 4 cores and it's cluster id starts at
bit 8 of the MPIDR.  To convert from the cluster id (0 or 1) to the
lowest CPU-ID in the respective cluster, we thus need to shift by 6
(i.e. shift by 8 to extract the cluster-id and multiply by 4).

This change is required to ensure the PSCI support can index the
per-cpu entry-address array correctly.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Change-Id: I64a76038f090a85a47067f09f750e96e3946e756

The Denver CPUs implement support for PMUv3 for ARMv8.1 and expect the
PMCR_EL0 to be saved in non-secure context.

This patch disables cycle counter when event counting is prohibited
immediately on entering the secure world to avoid leaking useful
information about the PMU counters. The context saving code later
saves the value of PMCR_EL0 to the non-secure world context.

Verified with 'PMU Leakage' test suite.

 ******************************* Summary *******************************
 > Test suite 'PMU Leakage'
                                                                 Passed
 =================================
 Tests Skipped : 2
 Tests Passed  : 2
 Tests Failed  : 0
 Tests Crashed : 0
 Total tests   : 4
 =================================
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I3675e2b99b44ed23d86e29a5af1b496e80324875

* changes:
  dualroot: add chain of trust for secure partitions
  sptool: append cert_tool arguments.
  cert_create: add SiP owned secure partitions support

Using the fconf framework, the Group 0 and Group 1 secure interrupt
descriptors are moved to device tree and retrieved in runtime. This
feature is enabled by the build flag SEC_INT_DESC_IN_FCONF.

Change-Id: I360c63a83286c7ecc2426cd1ff1b4746d61e633c
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

The only difference between GIC-500 and GIC-600 relevant to TF-A is the
differing power management sequence.
A certain GIC implementation is detectable at runtime, for instance by
checking the IIDR register. Let's add that test before initiating the
GIC-600 specific sequence, so the code can be used on both GIC-600 and
GIC-500 chips alike, without deciding on a GIC chip at compile time.

This means that the GIC-500 "driver" is now redundant. To allow minimal
platform support, add a switch to disable GIC-600 support.

Change-Id: I17ea97d9fb05874772ebaa13e6678b4ba3415557
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

A new certificate "sip-sp-cert" has been added for Silicon Provider(SiP)
owned Secure Partitions(SP). A similar support for Platform owned SP can
be added in future. The certificate is also protected against anti-
rollback using the trusted Non-Volatile counter.

To avoid deviating from TBBR spec, support for SP CoT is only provided
in dualroot.
Secure Partition content certificate is assigned image ID 31 and SP
images follows after it.

The CoT for secure partition look like below.
+------------------+       +-------------------+
| ROTPK/ROTPK Hash |------>| Trusted Key       |
+------------------+       | Certificate       |
                           | (Auth Image)      |
                          /+-------------------+
                         /                   |
                        /                    |
                       /                     |
                      /                      |
                     L                       v
+------------------+       +-------------------+
| Trusted World    |------>| SiP owned SPs     |
| Public Key       |       | Content Cert      |
+------------------+       | (Auth Image)      |
                        /   +-------------------+
                       /                      |
                      /                      v|
+------------------+ L     +-------------------+
| SP_PKG1 Hash     |------>| SP_PKG1           |
|                  |       | (Data Image)      |
+------------------+       +-------------------+
        .                           .
        .                           .
        .                           .
+------------------+       +-------------------+
| SP_PKG8 Hash     |------>| SP_PKG8           |
|                  |       | (Data Image)      |
+------------------+       +-------------------+
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ia31546bac1327a3e0b5d37e8b99c808442d5e53f

* changes:
  plat: intel: Additional instruction required to enable global timer
  plat: intel: Fix CCU initialization for Agilex
  plat: intel: Add FPGAINTF configuration to when configuring pinmux
  plat: intel: set DRVSEL and SMPLSEL for DWMMC
  plat: intel: Fix clock configuration bugs

There are additional instruction needed to enable the global timer.
This fixes the global timer initialization
Signed-off-by: Tien Hock Loh <tien.hock.loh@intel.com>
Change-Id: Idaf2d23359aacc417e2b7d8cdf1688b5cd17ca98

The CCU initialization loop uses the wrong units, this fixes that. This
also fixes snoop filter register set bits should be used instead of
overwriting the register
Signed-off-by: Tien Hock Loh <tien.hock.loh@intel.com>
Change-Id: Ia15eeeae5569b00ad84120182170d353ee221b31

The size of buffer currently used to store the FDT passed from U-Boot as
a platform parameter is not large enough to store some RK3399 device
trees. The largest RK3399 device tree currently in U-Boot (for the
Pinebook Pro) is about 70KB in size when passed to TF-A, so increase the
buffer size to 128K which gives some headroom for possibly larger FDTs
in future.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Change-Id: I414caf20683cd47c02ee470dfa988544f3809919

FPGAINTF wasn't enabled when configuring pinmux. This fixes the issue.
Signed-off-by: Tien Hock Loh <tien.hock.loh@intel.com>
Change-Id: I5a6aacd504901b8f7327b2f4854b8a77d0c37019

DRVSEL and SMPLSEL needs to be set so that it can properly go into full
speed mode. This needs to be done in EL3 as the registers are secured.
Signed-off-by: Tien Hock Loh <tien.hock.loh@intel.com>
Change-Id: Ia2f348e7742ff7b76da74d392ef1ce71e2f41677

This fixes a few issues on the Agilex clock configuration:
- Set clock manager into boot mode before configuring clock
- Fix wrong divisor used when calculating vcocalib
- PLL sync configuration should be read and then written
- Wait PLL lock after PLL sync configuration is done
- Clear interrupt bits instead of set interrupt bits after configuration
Signed-off-by: Tien Hock Loh <tien.hock.loh@intel.com>
Change-Id: I54c1dc5fe9b102e3bbc1237a92d8471173b8af70

To support secure boot of SP's update cert tool arguments while
generating sp_gen.mk which in turn is consumed by build system.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I2293cee9b7c684c27d387aba18e0294c701fb1cc

Add support to generate certificate "sip-sp-cert" for Secure
Partitions(SP) owned by Silicon provider(SiP).
To avoid deviation from TBBR specification the support is only added for
dualroot CoT and not for TBBR CoT.

A single certificate file is generated containing hash of individual
packages. Maximum 8 secure partitions are supported.

Following new options added to cert_tool:
 --sip-sp-cert --> SiP owned Secure Partition Content Certificate
 --sp-pkg1 --> Secure Partition Package1 file
 --sp-pkg2
 .....
 --sp-pkg8

Trusted world key pair is used for signing.

Going forward, this feature can be extended for Platfrom owned
Partitions, if required.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ia6dfbc1447cfb41b1fcbd12cf2bf7b88f409bd8d

As per "include/export/README", TF-A code should never include export
headers directly. Instead, it should include a wrapper header that
ensures the export header is included in the right manner.

"tbbr_img_def_exp.h" is directly included in TF-A code, this patch
replaces it with its  wrapper header "tbbr_img_def.h".
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I31c1a42e6a7bcac4c396bb17e8548567ecd8147d

Change a topology map from internal database
to SPD based for 32bit bus width mode

Change-Id: I803166893ddc2fd916fc8a1c27fffd34b6ec0c72
Signed-off-by: Alex Leibovich <alexl@marvell.com>

Update PLL configuration according to HW team guidelines.

Change-Id: I23cac4fb4a638e7416965a5399ce6947e08d0711
Signed-off-by: Alex Leibovich <alexl@marvell.com>