GitLab

This patch adds capability to FVP to disable authentication dynamically
via the `disable_auth` property in TB_FW_CONFIG. Both BL1 and BL2 parses
the TB_FW_CONFIG for the `disable_auth` property and invokes the
`load_dyn_disable_auth()` API to disable authentication if the
property is set to 1. The DYN_DISABLE_AUTH is enabled by default for
FVP as it is a development platform. Note that the TB_FW_CONFIG has to
be authenticated by BL1 irrespective of these settings.

The arm_bl2_dyn_cfg_init() is now earlier in bl2_plat_preload_setup()
rather than in bl2_platform_setup() as we need to get the value of
`disable_auth` property prior to authentication of any image by BL2.

Change-Id: I734acd59572849793e5020ec44c6ac51f654a4d1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Previously mem_protect used to be only supported from BL2. This is not
helpful in the case when ARM TF-A BL2 is not used. This patch demonstrates
mem_protect from el3_runtime firmware on ARM Platforms specifically
when RESET_TO_BL31 or RESET_TO_SP_MIN flag is set as BL2 may be absent
in these cases. The Non secure DRAM is dynamically mapped into EL3 mmap
tables temporarily and then the protected regions are then cleared. This
avoids the need to map the non secure DRAM permanently to BL31/sp_min.

The stack size is also increased, because DYNAMIC_XLAT_TABLES require
a bigger stack.

Change-Id: Ia44c594192ed5c5adc596c0cff2c7cc18c001fde
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Rule 8.4: A compatible declaration shall be visible when
          an object or function with external linkage is defined

Fixed for:
	make DEBUG=1 PLAT=fvp SPD=tspd all

Change-Id: I0a16cf68fef29cf00ec0a52e47786f61d02ca4ae
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

This patch allows the ARM Platforms to specify the TZC regions to be
specified to the ARM TZC helpers in arm_tzc400.c and arm_tzc_dmc500.c.
If the regions are not specified then the default TZC region will be
configured by these helpers.

This override mechanism allows specifying special regions for TZMP1
usecase.
Signed-off-by: Summer Qin <summer.qin@arm.com>

The current AArch32 version of plat_arm_calc_core_pos uses an incorrect
algorithm to calculate the linear position of a core / PE from its
MPIDR.

This patch corrects the algorithm to:

(ClusterId * FVP_MAX_CPUS_PER_CLUSTER) * FVP_MAX_PE_PER_CPU
+ (CPUId * FVP_MAX_PE_PER_CPU)
+ ThreadId

which supports cores where there are more than 1 PE per CPU.

NOTE: the AArch64 version was fixed in 39b21d19



Change-Id: I72aea89d8f72f8b1fef54e2177a0fa6fef0f5513
Signed-off-by: David Cunado <david.cunado@arm.com>

Ensure (where possible) that switch statements in plat comply with MISRA
rules 16.1 - 16.7.

Change-Id: Ie4a7d2fd10f6141c0cfb89317ea28a755391622f
Signed-off-by: Jonathan Wright <jonathan.wright@arm.com>

x3 will be assigned by the folloing instructions.
So the first instruction is not needed any more.

old method:
  (ClusterId * FVP_MAX_CPUS_PER_CLUSTER)
+ (CPUId * FVP_MAX_PE_PER_CPU)
+ ThreadId

it should be
  (ClusterId * FVP_MAX_CPUS_PER_CLUSTER) * FVP_MAX_PE_PER_CPU
+ (CPUId * FVP_MAX_PE_PER_CPU)
+ ThreadId

which can be simplified as:
(ClusterId * FVP_MAX_CPUS_PER_CLUSTER + CPUId) * FVP_MAX_PE_PER_CPU + ThreadId
Signed-off-by: Wang Feng <feng_feng.wang@spreadtrum.com>

The FVP platform port for SP_MIN (BL32) didn't map the flash memory
in BL32 for stroring the mem_protect enable state information leading
to synchronous exception. The patch fixes it by adding the region to
the BL32 mmap tables.

Change-Id: I37eec83c3e1ea43d1b5504d3683eebc32a57eadf
Signed-off-by: Joel Hutton <Joel.Hutton@Arm.com>

Previously, Juno used to depend on the SSC_GPRETN register to inform
about the reset syndrome. This method was removed when SCP migrated
to the SDS framework. But even the SDS framework doesn't report the
reset syndrome correctly and hence Juno failed to enter Firmware
update mode if BL2 authentication failed.

In addition to that, the error code populated in V2M_SYS_NVFLAGS register
does not seem to be retained any more on Juno across resets. This could
be down to the motherboard firmware not doing the necessary to preserve
the value.

Hence this patch modifies the Juno platform to use the same mechanism to
trigger firmware update as FVP which is to corrupt the FIP TOC on
authentication failure. The implementation in `fvp_err.c` is made common
for ARM platforms and is moved to the new `arm_err.c` file in
plat/arm/common folder. The BL1 and BL2 mmap table entries for Juno
are modified to allow write to the Flash memory address.

Change-Id: Ica7d49a3e8a46a90efd4cf340f19fda3b549e945
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch removes default platform implementations of sp_min
platform APIs from plat/common/aarch32/plat_common.c. The APIs
are now implemented in `plat_sp_min_common.c` file within the
same folder.

The ARM platform layer had a weak definition of sp_min_platform_setup2()
which conflicted with the weak definition in the common file. Hence this
patch fixes that by introducing a `plat_arm_` version of the API thus
allowing individual boards within ARM platforms to override it if they
wish to.

Fixes ARM-software/tf-issues#559

Change-Id: I11a74ecae8191878ccc7ea03f12bdd5ae88faba5
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This was correct according to the model specifications , but it seems
that FVP doesn't implement it. It is safer to use the size exposed by
the DTB which is currently used by Linux.

Change-Id: I9aabe3284a50ec2a36ed94966eb7e4ddf37cec3b
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Rule 8.4: A compatible declaration shall be visible when
          an object or function with external linkage is defined

Fixed for:
	make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all

Change-Id: I7c2ad3f5c015411c202605851240d5347e4cc8c7
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Rule 8.3: All declarations of an object or function shall
          use the same names and type qualifiers.

Fixed for:

	make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all

Change-Id: I48201c9ef022f6bd42ea8644529afce70f9b3f22
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

FVPs that model DynamIQ configuration implements all CPUs in a single
cluster. I.e., such models have a single cluster with more than 4 CPUs.
This differs from existing default build configuration for FVP where up
to 4 CPUs are assumed per cluster.

To allow building for DynamIQ configuration, promote the macro
FVP_MAX_CPUS_PER_CLUSTER as a build option to have it set from the build
command line. The value of the build option defaults to 4.

Change-Id: Idc3853bc95f680869b434b011c2dbd733e40c6ce
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

MISRA C-2012 Rule 7.3 violation: lowercase l shall not be used as literal suffixes.

This patch resolves this for the ULL() macro by using ULL suffix instead
of the ull suffix.

Change-Id: Ia8183c399e74677e676956e8653e82375d0e0a01
Signed-off-by: David Cunado <david.cunado@arm.com>

This patch restricts building the dynamic config DTBs to the Unix
build environment as the Device Tree compiler may not be available
on other build environments.

Change-Id: Ie690e80010a174300e966240fd977b37561156e0
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch also fixes the assumption that the counters are disabled on
the resume path.  This is incorrect as the AMU counters are enabled
early in the CPU reset function before `cpuamu_context_restore()`
runs.

Change-Id: I38a94eb166a523f00de18e86860434ffccff2131
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

This patch also fixes `cpuamu_write_cpuamcntenclr_el0()` to use an MSR
instruction instead of an MRS instruction.

Change-Id: Ia6531f64b5ebc60ba432124eaa8d8eaccba40ed0
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Change-Id: I1d85b76af002b8b672fcaeca94939b7420bc8243
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch adds TB_FW_CONFIG for FVP and allows FVP
to select the appropriate HW_CONFIG to include in the
fip. The HW_CONFIG for FVP is selected via `FVP_HW_CONFIG_DTS`
build option. The TB_FW_CONFIG specifies the load address of
HW_CONFIG to BL2. Since currently the load address is different
between AARCH32 and AARCH64, 2 separate TB_FW_CONFIGs are
maintained for the 2 modes.

Change-Id: Ide8581e752dfa900087f5895c775073c841c0daf
Signed-Off-By: Soby Mathew <soby.mathew@arm.com>

The patch adds the necessary changes to load HW_CONFIG in BL2 for
ARM Platforms :

1. The load address of HW_CONFIG is specified via the `hw_config_addr`
property in TB_FW_CONFIG is loaded by BL1. The `hw_config_max_size`
property defines the maximum size to be expected for the HW_CONFIG.
The `arm_dyn_cfg_helpers.c` and corresponding header implements
utility functions to parse these DT properties defined.
The `arm_dyn_cfg.c` implements wrappers to these helpers to enable
them to be invoked from ARM platform layer.

2. `HW_CONFIG` is added to the `bl2_mem_params_descs[]` array which is
the list of images to be loaded by BL2.

3. The `libfdt` sources are now included when BL2 is built

4. A new helper `populate_next_bl_params_config()` is introduced in
desc_image_load.c to populate the subsequent executable BL images
with the `hw_config` and the corresponding `fw_config` if available.
The `plat_get_next_bl_params()` API for ARM platforms is modified to
invoke this new helper.

5. The implementation of `bl2_early_platform_setup2()` is modified to
consider `arg0` as well in addition to `arg1` passed from BL1.

6. Bump up the BL2 size for Juno to accommodate the inclusion of libfdt.

Change-Id: I80f1554adec41753e0d179a5237364f04fe13a3f
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch modifies the bl1_platform_setup() API to load and authenticate
TB_FW_CONFIG in BL1. The load address of the same is passed on to BL2 in
`arg0` of entrypoint info. The fvp_io_storage.c and arm_io_storage.c also
adds entries corresponding to TB_FW_CONFIG. A helper function
`arm_load_tb_fw_config()` is added to load and authenticate TB_FW_CONFIG
if present.

Change-Id: Ie7bce667b3fad2b1a083bbcbc0a773f9f04254b1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch migrates the ARM Standard platforms to the new BL
handover interface. The arm_blx_early_platform_setup() functions
are also modified to take in 4 arguments. The `ARM_BL31_PLAT_PARAM_VAL`
value passed to BL31 from BL2 is now in arg3 in preparation of dynamic
configuration arguments.

Change-Id: I33e8e61325a19e7a7127b1ff203c3b86921bf153
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This patch maps the devices in the first GB of the system address map
on the FVP into the S-EL1&0 translation regime when SPM support is
enabled. This grants the Secure Partition access to the devices in
this region, for example the memory-mapped Generic Timer device.

Change-Id: I3aeea65f859ecbe83efde2acee20c55500c451bc
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

This patch modifies the makefiles to avoid the definition
of BL1_SOURCES and BL2_SOURCES in the tbbr makefiles, and
it lets to the platform makefiles to define them if they
actually need these images. In the case of BL2_AT_EL3
BL1 will not be needed usually because the Boot ROM will
jump directly to BL2.

Change-Id: Ib6845a260633a22a646088629bcd7387fe35dcf9
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

This patch add supports for the new API added for BL2 at EL3 for
FVP. We don't have a non-TF Boot ROM for FVP, but this option can be
tested setting specific parameters in the model.

The bl2 image is loaded directly in memory instead of being loaded
by a non-TF Boot ROM and the reset address is changed:

	--data cluster0.cpu0=bl2.bin@0x4001000
	-C cluster0.cpu0.RVBAR=0x4001000

These parameters mean that in the cold boot path the processor will
jump to BL2 again. For this reason, BL2 is loaded in dram in this
case, to avoid other images reclaiming BL2 memory.

Change-Id: Ieb2ff8535a9e67ccebcd8c2212cad366e7776422
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Change-Id: I504d3f65ca5829bc1f4ebadb764931f8379ee81f
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

With this patch, ARM platforms are expected to define the macros
PLAT_ARM_SDEI_PRIVATE_EVENTS and PLAT_ARM_SDEI_SHARED_EVENTS as a list
of private and shared events, respectively. This allows for individual
platforms to define their own events.

Change-Id: I66851fdcbff83fd9568c2777ade9eb12df284b49
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

After returning from SYSTEM_SUSPEND state, BL31 reconfigures the
TrustZone Controller during the boot sequence. If BL31 is placed in
TZC-secured DRAM, it will try to change the permissions of the memory it
is being executed from, causing an exception.

The solution is to disable SYSTEM_SUSPEND when the Trusted Firmware has
been compiled with ``ARM_BL31_IN_DRAM=1``.

Change-Id: I96dc50decaacd469327c6b591d07964726e58db4
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Common code mustn't include ARM platforms headers.

Change-Id: Ib6e4f5a77c2d095e6e8c3ad89c89cb1959cd3043
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Change-Id: I96de88f44c36681ad8a70430af8e01016394bd14
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Factor out SPE operations in a separate file.  Use the publish
subscribe framework to drain the SPE buffers before entering secure
world.  Additionally, enable SPE before entering normal world.

A side effect of this change is that the profiling buffers are now
only drained when a transition from normal world to secure world
happens.  Previously they were drained also on return from secure
world, which is unnecessary as SPE is not supported in S-EL1.

Change-Id: I17582c689b4b525770dbb6db098b3a0b5777b70a
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

The function arm_validate_ns_entrypoint() validates a given non-secure
physical address. This function however specifically returns PSCI error
codes.

Non-secure physical address validation is potentially useful across ARM
platforms, even for non-PSCI use cases. Therefore make this function
common by returning 0 for success or -1 otherwise.

Having made the function common, make arm_validate_psci_entrypoint() a
wrapper around arm_validate_ns_entrypoint() which only translates return
value into PSCI error codes. This wrapper is now used where
arm_validate_ns_entrypoint() was currently used for PSCI entry point
validation.

Change-Id: Ic781fc3105d6d199fd8f53f01aba5baea0ebc310
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

This initial port of the Secure Partitions Manager to FVP supports BL31
in both SRAM and Trusted DRAM.

A document with instructions to build the SPM has been added.

Change-Id: I4ea83ff0a659be77f2cd72eaf2302cdf8ba98b32
Co-authored-by: Douglas Raillard <douglas.raillard@arm.com>
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Co-authored-by: Achin Gupta <achin.gupta@arm.com>
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

An earlier patch added provision for the platform to provide secure
interrupt properties. ARM platforms already has a list of interrupts
that fall into different secure groups.

This patch defines macros that enumerate interrupt properties in the
same fashion, and points the driver driver data to a list of interrupt
properties rather than list of secure interrupts on ARM platforms.  The
deprecated interrupt list definitions are however retained to support
legacy builds.

Configuration applied to individual interrupts remain unchanged, so no
runtime behaviour change expected.

NOTE: Platforms that use the arm/common function
plat_arm_gic_driver_init() must replace their PLAT_ARM_G1S_IRQS and
PLAT_ARM_G0_IRQS macro definitions with PLAT_ARM_G1S_IRQ_PROPS and
PLAT_ARM_G0_IRQ_PROPS macros respectively, using the provided
INTR_PROP_DESC macro.

Change-Id: I24d643b83e3333753a3ba97d4b6fb71e16bb0952
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Provides GICv3 save/restore feature to arm_system_pwr_domain_resume and
arm_system_pwr_domain_save functions.

Introduce FVP PSCI power level 3 (System level) support. This is solely
done to provide example code on how to use the GICv3 save and restore
helpers.

Also make CSS GICv3 platforms power off the Redistributor on SYSTEM
SUSPEND as its state is saved and restored.

Change-Id: I0d852f3af8824edee1a17c085cf593ddd33a4e77
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Co-Authored-by: Douglas Raillard <douglas.raillard@arm.com>

Some recent enhancements to EL3 runtime firmware like support for
save and restoring GICv3 register context during system_suspend
necessitates additional data memory for the firmware. This patch
introduces support for creating a TZC secured DDR carveout for use
by ARM reference platforms. A new linker section `el3_tzc_dram` is
created using platform supplied linker script and data marked with
the attribute `arm_el3_tzc_dram` will be placed in this section.
The FVP makefile now defines the `PLAT_EXTRA_LD_SCRIPT` variable to
allow inclusion of the platform linker script by the top level BL31
linker script.

Change-Id: I0e7f4a75a6ac51419c667875ff2677043df1585d
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

During system suspend, the GICv3 Distributor and Redistributor context
can be lost due to power gating of the system power domain. This means
that the GICv3 context needs to be saved prior to system suspend and
restored on wakeup. Currently the consensus is that the Firmware should
be in charge of this. See tf-issues#464 for more details.

This patch introduces helper APIs in the GICv3 driver to save and
restore the Distributor and Redistributor contexts. The GICv3 ITS
context is not considered in this patch because the specification says
that the details of ITS power management is implementation-defined.
These APIs are expected to be appropriately invoked by the platform
layer during system suspend.

Fixes ARM-software/tf-issues#464

Change-Id: Iebb9c6770ab8c4d522546f161fa402d2fe02ec00
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

Commit 11ad8f20

 added supporting
multi-threaded CPUs on FVP platform, including modifications for
calculating CPU IDs. This patch imports the strong definition of the
same CPU ID calculation on FVP platform for TSP.

Without this patch, TSP on FVP was using the default CPU ID calculation,
which would end up being wrong on CPUs with multi-threading.

Change-Id: If67fd492dfce1f57224c9e693988c4b0f89a9a9a
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

On ARM platforms, the maximum size of the address space is limited
to 32-bits as defined in arm_def.h. In order to access DRAM2, which
is defined beyond the 32-bit address space, the maximum address space
is increased to 36-bits in AArch64. It is possible to increase the
virtual space for AArch32, but it is more difficult and not supported
for now.

NOTE - the actual maximum memory address space is platform dependent
and is checked at run-time by querying the PARange field in the
ID_AA64MMFR0_EL1 register.

Change-Id: I6cb05c78a63b1fed96db9a9773faca04a5b93d67
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>