Skip to content

GitLab

Switch branch/tag
  1. 20 Jan, 2020 6 commits
  3. 15 Jan, 2020 11 commits
  5. 13 Jan, 2020 1 commit
  7. 12 Jan, 2020 2 commits
  9. 10 Jan, 2020 2 commits
    • Deepika Bhavnani's avatar
      Unify type of "cpu_idx" across PSCI module. · 5b33ad17
      Deepika Bhavnani authored 
      

NOTE for platform integrators:
   API `plat_psci_stat_get_residency()` third argument
   `last_cpu_idx` is changed from "signed int" to the
   "unsigned int" type.

Issue / Trouble points
1. cpu_idx is used as mix of `unsigned int` and `signed int` in code
with typecasting at some places leading to coverity issues.

2. Underlying platform API's return cpu_idx as `unsigned int`
and comparison is performed with platform specific defines
`PLAFORM_xxx` which is not consistent

Misra Rule 10.4:
The value of a complex expression of integer type may only be cast to
a type that is narrower and of the same signedness as the underlying
type of the expression.

Based on above points, cpu_idx is kept as `unsigned int` to match
the API's and low-level functions and platform defines are updated
where ever required
Signed-off-by: default avatarDeepika Bhavnani <deepika.bhavnani@arm.com>
Change-Id: Ib26fd16e420c35527204b126b9b91e8babcc3a5c
      5b33ad17
    • Alexei Fedorov's avatar
      FVP: Remove re-definition of topology related build options · 94f1c959
      Alexei Fedorov authored 
      

This patch removes re-definition of the following FVP build
options from plat\arm\board\fvp\fvp_def.h:
 'FVP_CLUSTER_COUNT'
 'FVP_MAX_CPUS_PER_CLUSTER'
 'FVP_MAX_PE_PER_CPU'
which are set in platform.mk.

This fixes a potential problem when a build option set in
platform.mk file can be re-defined in fvp_def.h header file
used by other build component with a different makefile which
does not set this option.
Ref. GENFW-3505.

Change-Id: I4288629920516acf2c239c7b733f92a0c5a812ff
Signed-off-by: default avatarAlexei Fedorov <Alexei.Fedorov@arm.com>
      94f1c959
  11. 09 Jan, 2020 3 commits
  13. 08 Jan, 2020 1 commit
  15. 07 Jan, 2020 10 commits
  17. 06 Jan, 2020 2 commits
  19. 03 Jan, 2020 1 commit
    • Vishnu Banavath's avatar
      drivers: add a driver for snoop control unit · c20c0525
      Vishnu Banavath authored 
      

The SCU connects one to four Cortex-A5/Cortex-A9 processors
to the memory system through the AXI interfaces.

The SCU functions are to:
- maintain data cache coherency between the Cortex-A5/Cortex-A9
  processors
- initiate L2 AXI memory accesses
- arbitrate between Cortex-A5/Cortex-A9 processors requesting
  L2 accesses
- manage ACP accesses.

Snoop Control Unit will enable to snoop on other CPUs caches.
This is very important when it comes to synchronizing data between
CPUs. As an example, there is a high chance that data might be
cache'd and other CPUs can't see the change. In such cases,
if snoop control unit is enabled, data is synchoronized immediately
between CPUs and the changes are visible to other CPUs.

This driver provides functionality to enable SCU as well as enabling
user to know the following
- number of CPUs present
- is a particular CPU operating in SMP mode or AMP mode
- data cache size of a particular CPU
- does SCU has ACP port
- is L2CPRESENT

Change-Id: I0d977970154fa60df57caf449200d471f02312a0
Signed-off-by: default avatarVishnu Banavath <vishnu.banavath@arm.com>
      c20c0525
  21. 30 Dec, 2019 1 commit
    • Andre Przywara's avatar
      plat: rpi4: Skip UART initialisation · 0eda713b
      Andre Przywara authored 
      

So far we have seen two different clock setups for the Raspberry Pi 4
board, with the VPU clock divider being different. This was handled by
reading the divider register and adjusting the base clock rate
accordingly.
Recently a new GPU firmware version appeared that changed the clock rate
*again*, though this time at a higher level, so the VPU rate (and the
apparent PLLC parent clock) did not seem to change, judging by reading
the clock registers.
So rather than playing cat and mouse with the GPU firmware or going
further down the rabbit hole of exploring the whole clock tree, let's
just skip the baud rate programming altogether. This works because the
GPU firmware actually sets up and programs the debug UART already, so
we can just use it.

Pass 0 as the base clock rate to let the console driver skip the setup,
also remove the no longer needed clock code.
Signed-off-by: default avatarAndre Przywara <andre.przywara@arm.com>
Change-Id: Ica88a3f3c9c11059357c1e6dd8f7a4d9b1f98fd7
      0eda713b