plat/arm: Migrate AArch64 port to the multi console driver

xlat_v2: add a check on mm_cursor->size to avoid infinite loop

The old API is deprecated and will eventually be removed.

Arm platforms now use the multi console driver for boot and runtime
consoles. However, the crash console uses the direct console API because
it doesn't need any memory access to work. This makes it more robust
during crashes.

The AArch32 port of the Trusted Firmware doesn't support this new API
yet, so it is only enabled in AArch64 builds. Because of this, the
common code must maintain compatibility with both systems. SP_MIN
doesn't have to be updated because it's only used in AArch32 builds.
The TSP is only used in AArch64, so it only needs to support the new
API without keeping support for the old one.

Special care must be taken because of PSCI_SYSTEM_SUSPEND. In Juno, this
causes the UARTs to reset (except for the one used by the TSP). This
means that they must be unregistered when suspending and re-registered
when resuming. This wasn't a problem with the old driver because it just
re...

Allwinner platform support

SPM: Refactor entry and exit of the SP

Genmask

Only use synchronous calls to enter the Secure Partition in order to
simplify the SMC handling code.

Change-Id: Ia501a045585ee0836b9151141ad3bd11d0971be2
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Some peripherals are TrustZone aware, so they need to be configured to
be accessible from non-secure world, as we don't need any of them being
exclusive to the secure world.
This affects some clocks, DMA channels and the Secure Peripheral
Controller (SPC). The latter controls access to most devices, but is not
active unless booting with the secure boot fuse burnt.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The reset vector entry point is preserved across CPU resets, so it only
needs to be set once at boot.

Hotplugged CPUs are not actually powered down, but are put in a wfi with
the GIC disconnected.

With this commit, Linux is able to enable, hotplug and use all four CPUs.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

sun50i_cpu_on will be used by the PSCI implementation to initialize
secondary cores for SMP. Unfortunately, sun50i_cpu_off is not usable by
PSCI directly, because it is not possible for a CPU to use this function
to power itself down. Power cannot be shut off until the outputs are
clamped, and MMIO does not work once the outputs are clamped.

But at least CPU0 can shutdown the other cores early in the BL31 boot
process and before shutting down the system.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The Allwinner A64 SoC is quite popular on single board computers.
It comes with four Cortex-A53 cores in a singe cluster and the usual
peripherals for set-top box/tablet SoC.

The ATF platform target is called "sun50i_a64".

[Andre: adapted to amended directory layout, removed unneeded definitions ]
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

This platform supports Allwinner's SoCs with ARMv8 cores. So far they
all sport a single cluster of Cortex-A53 cores.

"sunxi" is the original code name used for this platform, and since it
appears in the Linux kernel and in U-Boot as well, we use it here as a
short file name prefix and for identifiers.

This port includes BL31 support only. U-Boot's SPL takes the role of the
primary loader, also doing the DRAM initialization. It then loads the
rest of the firmware, namely ATF and U-Boot (BL33), then hands execution
over to ATF.

This commit includes the basic platform code shared across all SoCs.
There is no platform.mk yet.

[Andre: moved files into proper directories, supported RESET_TO_BL31,
	various clean ups and simplifications ]
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

When applying some MISRA rules, lots of issues are raised with BIT macro
on AARCH32, and cast on uint32_t would be required (Rule 10.3).
The macros BIT_32 and BIT_64 are then created for 32bit and 64bit.
Then the BIT macro defaults on BIT_64 on AARCH64,
and on BIT_32 on AARCH32.
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Import GENMASK_32 and GENMASK_64 macros from optee-os (permissive license).
And default GENMASK is set to GENMASK_32 for AARCH32,
and to GENMASK_64 for 64bit arch.

fixes arm-software/tf-issues#596
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>

rpi3: Fix kernel boot documentation

Correct ordering of log levels in documentation

rockchip: Move stdint header to the offending header file

Minor fixes to SPM

uniphier: fix CCI-500 connection for LD20

The issue can occur if end_va is equal to the max architecture address,
and when mm_cursor point to the last entry of mmap_region_t table: {0}.
The first line of the while will then be true, e.g. on AARCH32, we have:
mm_cursor->base_va (=0) + mm_cursor->size (=0) - 1 == end_va (=0xFFFFFFFF)
And the mm_cursor->size = 0 will be lesser than mm->size

A check on mm_cursor->size != 0 should be done as in the previous while,
to avoid such kind of infinite loop.

fixes arm-software/tf-issues#594
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Changed the ordering of the log levels in the documentation to
mate the code

Change-Id: Ief1930b73d833fdf675b039c98046591c0c264c1
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

The stdint header was introduced to rk3399's plat_sip_calls.c in order
to fix missing stdint definitions. However, ordering headers
alphabetically caused the fix to be ineffective, as stint was then
included after the offending header file (dfs.h).

Move the stdint include to that header to properly fix the issue.

Change-Id: Ieaad37a7932786971488ab58fc5b169bfa79e197
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>

The order of the arguments of memmap was swapped. The old command was
reserving 256 MiB from the 16 MiB barrier, it should be reserving only
16 MiB at the 256 MiB barrier.

It worked because the memory used by the Trusted Firmware was reserved
anyway.

Change-Id: I3fefcfc0105ecf05ba5606517bc3236f4eb24ceb
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

drivers: ti: uart: Add TI specific 16550 initialization

MISRA 5.1, 5.3 & 5.7 compliance changes

The translation tables allocated for the Secure Partition do not need
to be treated as a special case. They can be put amongst the other
tables mapping BL31's general purpose memory. They will be mapped with
the same attributes as them, which is fine.

The explicit alignment constraint in BL31's linker script to pad the
last page of memory allocated to the Secure Partition's translation
tables is useless too, as page tables are per se pages, thus their
end address is naturally aligned on a page-boundary.

In fact, this patch does not change the existing behaviour. Since
patch 22282bb6

 ("SPM: Move all SP-related info to SP context
struct"), the secure_partition.c file has been renamed into sp_xlat.c
but the linker script has not been properly updated. As a result, the
SP translation tables are not specifically put at the start of the
xlat_table linker section, the __SP_IMAGE_XLAT_TABLES_START__/_END__
symbols have the same value, the size of the resulting mmap_region
covering these xlat tables is 0 and so it is ignored.

Change-Id: I4cf0a4cc090298811cca53fc9cee74df0f2b1512
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

The function xlat_arch_is_granule_size_supported() can be used to check
if a specific granule size is supported. In Armv8, AArch32 only supports
4 KiB pages. AArch64 supports 4 KiB, 16 KiB or 64 KiB depending on the
implementation, which is detected at runtime.

The function xlat_arch_get_max_supported_granule_size() returns the max
granule size supported by the implementation.

Even though right now they are only used by SPM, they may be useful in
other places in the future. This patch moves the code currently in SPM
to the xlat tables lib so that it can be reused.

Change-Id: If54624a5ecf20b9b9b7f38861b56383a03bbc8a4
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

In the context management library, cm_setup_context() takes the
information in ep_info to fill the registers x0-x7. This patch replaces
the current code that sets them manually by the correct initialization
code.

Change-Id: Id1fdf4681b154026c2e3af1f9b05b19582b7d16d
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

In LOAD_IMAGE_V1 (i.e when LOAD_IMAGE_V2=0) the bl2_tzram_layout is,
by default, assigned to the bl1_tzram_layout->free_base which is
dynamically calculated based on the images loaded in memory. There is a
chance that the bl2_tzram_layout will be assigned a value not aligned to
8 bytes. This patch rounds up the free_base value for the required
alignment.

This doesn't happen in LOAD_IMAGE_V2 because the bl2_tzram_layout is
assigned by default to the bl1_tzram_layout->total_base, which is
aligned.

Change-Id: Idc583e7dad993d02ac6791797406118c96f83fa1
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Rule 5.7: A tag name shall be a unique identifier

Follow convention of shorter names for smaller scope to fix
violations of MISRA rule 5.7

Fixed For:
    make ARM_TSP_RAM_LOCATION=tdram LOG_LEVEL=50 PLAT=fvp SPD=opteed

Change-Id: I5fbb5d6ebddf169550eddb07ed880f5c8076bb76
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

Follow convention of shorter names for smaller scope to fix
violations of MISRA rule 5.7

To prevent violation of directive 4.5 having variable name channel
in css_pm_scmi.c not being typographically ambiguous change macro
argument CHANNEL in css_mhu_doorbell.h change argument to _channel
to fit with our convention which is a permitted exception of
directive 4.5 for this project

Rule 5.7: A tag name shall be a unique identifier

Fixed for:
    make LOG_LEVEL=50 PLAT=juno

Change-Id: I147cdb13553e83ed7df19149b282706db115d612
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

Rule 5.7: A tag name shall be a unique identifier

There were 2 amu_ctx struct type definitions:
    - In lib/extensions/amu/aarch64/amu.c
    - In lib/cpus/aarch64/cpuamu.c

Renamed the latter to cpuamu_ctx to avoid this name clash

To avoid violation of Rule 8.3 also change name of function
amu_ctxs to unique name (cpuamu_ctxs) since it now returns a
different type (cpuamu_ctx) than the other amu_ctxs function

Fixed for:
    make LOG_LEVEL=50 PLAT=fvp

Change-Id: Ieeb7e390ec2900fd8b775bef312eda93804a43ed
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

Use a _ prefix for macro arguments to prevent that argument from
hiding variables of the same name in the outer scope

Rule 5.3: An identifier declared in an inner scope shall not
          hide an identifier declared in an outer scope

Fixed For:
    make LOG_LEVEL=50 PLAT=juno

Change-Id: I575fbc96e8267f2b075e88def1f6e3185394613a
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

Use a _ prefix for macro arguments to prevent that argument from
hiding variables of the same name in the outer scope

Rule 5.3: An identifier declared in an inner scope shall not
          hide an identifier declared in an outer scope

Fixed For:
    make PLAT=fvp USE_COHERENT_MEM=0

Change-Id: If50c583d3b63799ee6852626b15be00c0f6b10a0
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

Use a _ prefix for macro arguments to prevent that argument from
hiding variables of the same name in the outer scope

Rule 5.3: An identifier declared in an inner scope shall not
          hide an identifier declared in an outer scope

Fixed For:
    make PLAT=fvp SPD=tspd

Change-Id: I2d711b9584c4cb9ba3814ecd2ca65a42b7e24179
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

Use a _ prefix for Macro arguments to prevent that argument from
hiding variables of the same name in the outer scope

Rule 5.3: An identifier declared in an inner scope shall not
          hide an identifier declared in an outer scope

Fixed For:
    make LOG_LEVEL=50 PLAT=fvp

Change-Id: I67b6b05cbad4aeca65ce52981b4679b340604708
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

Conflict with function name and variable name within that function.
Change the name of the function from image_size to get_image_size
to remove conflict and make the function fit the normal project
naming convention.

Rule 5.3:  An identifier declared in an inner scope shall not
           hide an identifier declared in an outer scope

Fixed For:
    make LOG_LEVEL=50 PLAT=fvp

Change-Id: I1a63d2730113e2741fffa79730459c584b0224d7
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

Rule 5.1: External identifiers shall be distinct

Some of the identifier names in the GICv3 driver were so long that the
first 31 characters were identical. This patch shortens these names to
make sure they are different.

Fixed for:
    LOG_LEVEL=50 PLAT=fvp

Change-Id: Iecd551e3a015d144716b87b42c83dd3ab8c34d90
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

MISRA rule 21.15 fix

The slave ports of LD20 CCI-500 are connected as follows:

  S0: CA53
  S1: CA72

Be careful because the slave interface is not arranged in the
cluster number order (CA72: cluster 0, CA53: cluster 1).
Root-caused-by: Tetsuya Yoshizaki <yoshizaki.tetsuya@socionext.com>
Signed-off-by: Satoshi Ikawa <ikawa.satoshi@socionext.com>