GitLab

In order to access MG SRAM, the amb bridge needs to be configured which is
done in bl2 platform init.

For MG CM3, the image is only loaded to its SRAM and the CM3 itself is
left in reset. It is because the next stage bootloader (e.g. u-boot)
will trigger action which will take it out of reset when needed. This
can happen e.g. when appropriate device-tree setup (which has enabled
802.3 auto-neg) will be chosen. In other cases the MG CM3 should not be
running.

Change-Id: I816ea14e3a7174eace068ec44e3cc09998d0337e
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>

* changes:
  Introduce COT build option
  cert_create: Remove references to TBBR in common code
  cert_create: Introduce COT build option
  cert_create: Introduce TBBR CoT makefile

Allows to select the chain of trust to use when the Trusted Boot feature
is enabled. This affects both the cert_create tool and the firmware
itself.

Right now, the only available CoT is TBBR.

Change-Id: I7ab54e66508a1416cb3fcd3dfb0f055696763b3d
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

In preparation of supporting alternate chains of trust, reword comments
and error messages that explicitly mentioned TBBR.

Change-Id: I85a0b08e16d0cd82f3b767fcc092d1f20f45939f
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

It allows to select the desired chain of trust. Right now, only the TBBR
CoT is available.

At this stage, this build option only affects the tool itself. It is not
plugged into the rest of the build system yet. To use it:

 > make -C tools/cert_create COT=tbbr

Change-Id: I4484418f76d3c7b330d8653c978499a181534dcd
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

Move all TBBR-specific stuff out of the tool's makefile into a
sub-makefile. This will make it easier to define and select an alternate
chain of trust in the future.

Change-Id: I92e366a1999b74cf51127d1771b64b807cd94b29
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

This is based on the rpi implementation from
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/2746

.
Signed-off-by: Andrew Walbran <qwandor@google.com>
Change-Id: I5fe324fcd9d5e232091e01267ea12147c46bc9c1

* changes:
  qemu: Implement qemu_system_off via semihosting.
  qemu: Support ARM_LINUX_KERNEL_AS_BL33 to pass FDT address.

This flag warns if anything is declared more than once in the same
scope, even in cases where multiple declaration is valid and changes
nothing.

Consequently, this patch also fixes the issues reported by this
flag. Consider the following two lines of code from two different source
files(bl_common.h and bl31_plat_setup.c):

IMPORT_SYM(uintptr_t, __RO_START__, BL_CODE_BASE);
IMPORT_SYM(unsigned long, __RO_START__, BL2_RO_BASE);

The IMPORT_SYM macro which actually imports a linker symbol as a C expression.
The macro defines the __RO_START__ as an extern variable twice, one for each
instance. __RO_START__ symbol is defined by the linker script to mark the start
of the Read-Only area of the memory map.

Essentially, the platform code redefines the linker symbol with a different
(relevant) name rather than using the standard symbol. A simple solution to
fix this issue in the platform code for redundant declarations warning is
to remove the second IMPORT_SYM and replace it with following assignment

static const unsigned long BL2_RO_BASE = BL_CODE_BASE;

Change-Id: If4835d1ee462d52b75e5afd2a59b64828707c5aa
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

This patch adds 'calc_hash' function using Mbed TLS library
required for Measured Boot support.

Change-Id: Ifc5aee0162d04db58ec6391e0726a526f29a52bb
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

The Secure Configuration Register is 64-bits in AArch64 and 32-bits in
AArch32. Use u_register_t instead of unsigned int to reflect this.

Change-Id: I51b69467baba36bf0cfaec2595dc8837b1566934
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

* changes:
  ti: k3: drivers: ti_sci: Put sequence number in coherent memory
  ti: k3: drivers: ti_sci: Remove indirect structure of const data
  ti: k3: common: Enable ARM cluster power down
  ti: k3: common: Rename device IDs to be more consistent

This patch enables the config to switch to the console provided
by the SPE firmware.

Change-Id: I5a3bed09ee1e84f958d0925501d1a79fb7f694de
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

The current message sequence number is accessed both with caches on and
off so put this memory in the un-cached coherent section so accesses
are consistent and coherency is maintained.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Change-Id: Ieeefefeaffc691e4e4c4de7c74490d50ff9de807

The 'info' structure contained what is only static data for this
implementation of TI-SCI. Remove this indirection and remove the
struct.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Change-Id: I2328fddf388bf7d56a56bd673c080e78c86fe072

When all cores in a cluster are powered down the parent cluster can
be also powered down. When the last core has requested powering down
follow by sending the cluster power down sequence to the system
power controller firmware.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Change-Id: I0ffeb339852c66ef62743aecd3e17ca20bad6216

The core number is called 'core_id' but the processor and device IDs are
called 'proc' and 'device'. Rename these to make them less confusing.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Change-Id: I3d7c6dddd7aa37b5dee1aa9689ce31730e9c3b59

bakery_lock_get() uses DMB LD after lock acquisition and
bakery_lock_release() uses DMB ST before releasing the lock. This is
insufficient in both cases. With just DMB LD, stores in the critical
section can be reordered before the DMB LD which could mean writes in
the critical section completing before the lock has been acquired
successfully. Similarly, with just DMB ST, a load in the critical section
could be reordered after the the DMB ST. DMB is the least expensive
barrier that can provide the required ordering.
Signed-off-by: Raghu Krishnamurthy <raghu.ncstate@icloud.com>
Change-Id: Ieb74cbf5b76b09e1789331b71f37f7c660221b0e

* changes:
  uniphier: make all BL images completely position-independent
  uniphier: make uniphier_mmap_setup() work with PIE
  uniphier: pass SCP base address as a function parameter
  uniphier: set buffer offset and length for io_block dynamically
  uniphier: use more mmap_add_dynamic_region() for loading images
  bl_common: add BL_END macro
  uniphier: turn on ENABLE_PIE
  TSP: add PIE support
  BL2_AT_EL3: add PIE support
  BL31: discard .dynsym .dynstr .hash sections to make ENABLE_PIE work
  PIE: pass PIE options only to BL31
  Build: support per-BL LDFLAGS

CPUECTLR_EL1.EXTLLC bit indicates the presense of internal or external
last level cache(LLC) in the system, the reset value is internal LLC.

To cater for the platforms(like N1SDP) which has external LLC present
introduce a new build option 'NEOVERSE_N1_EXTERNAL_LLC' which can be
enabled by platform port.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ibf475fcd6fd44401897a71600f4eafe989921363

The platform topology description of the upcoming Arm's RD platforms
have different topology than those listed in the sgi_topology.c file. So
instead of adding platform specific topology into existing
sgi_topology.c file, those can be added to respective board files. In
order to maintain consistency with the upcoming platforms, move the
existing platform topology description to respective board files.

Change-Id: I4689c7d24cd0c75a3dc234370c34a85c08598abb
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>

As on SGI platforms, SCPI is unsupported on SGM platforms.

Change-Id: I556ed095b9eb55b72447230ee2725d3c76160a08
Signed-off-by: Chris Kay <chris.kay@arm.com>

PLATFORM_CORE_COUNT - Unsigned int
PLATFORM_CLUSTER_COUNT - Unsigned int
PLATFORM_MAX_CPUS_PER_CLUSTER - Unsigned int
PLATFORM_CORE_COUNT_PER_CLUSTER - Unsigned int
Signed-off-by: Deepika Bhavnani <deepika.bhavnani@arm.com>
Change-Id: I76f5535f1cbdaf3fc1235cd824111d9afe8f7e1b

This platform supports multiple SoCs. The next SoC will still keep
quite similar architecture, but the memory base will be changed.

The ENABLE_PIE improves the maintainability and usability. You can reuse
a single set of BL images for other SoC/board without re-compiling TF-A
at all. This will also keep the code cleaner because it avoids #ifdef
around various base addresses.

By defining ENABLE_PIE, BL2_AT_EL3, BL31, and BL32 (TSP) are really
position-independent now. You can load them anywhere irrespective of
their link address.

Change-Id: I8d5e3124ee30012f5b3bfa278b0baff8efd2fff7
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

BL2_BASE, BL31_BASE, and BL32_BASE are defined in platform_def.h,
that is, determined at link-time.

On the other hand, BL2_END, BL31_END, and BL32_END are derived from
the symbols produced by the linker scripts. So, they are fixed-up
at run-time if ENABLE_PIE is enabled.

To make it work in a position-indepenent manner, use BL_CODE_BASE and
BL_END, both of which are relocatable.

Change-Id: Ic179a7c60eb64c5f3024b178690b3ac7cbd7521b
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Currently, UNIPHIER_SCP_BASE is hard-coded in uniphier_scp_start(),
which is not handy for PIE.

Towards the goal of making this really position-independent, pass in
image_info->image_base.

Change-Id: I88e020a1919c607b1d5ce70b116201d95773bb63
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Currently, the .buffer field in io_block_dev_spec is statically set,
which is not handy for PIE.

Towards the goal of making this really position-independent, set the
buffer length and length in the uniphier_io_block_setup() function.

Change-Id: I22b20d7b58d6ffd38f64f967a2820fca4bd7dade
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Currently, uniphier_bl2_mmap hard-codes the memory region needed for
loading other images.

Towards the goal of making this really position-independent, call
mmap_add_dynamic_region() before that region gets accessed.

Change-Id: Ieb505b91ccf2483e5f1a280accda564b33f19f11
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Currently, the end address macros are defined per BL, like BL2_END,
BL31_END, BL32_END. They are not handy in the common code shared
between multiple BL stages.

This commit introduces BL_END, which is equivalent to BL{2,31,32}_END,
and will be useful for the BL-common code.

Change-Id: I3c39bf6096d99ce920a5b9fa21c0f65456fbfe8a
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>