GitLab

This patch removes the unused header from the Tegra194
platform files. As a result, the TSA MMIO would be
removed from the memory map too.

Change-Id: I2d38b3da7a119f5dfd6cfd429e481f4e6ad3481e
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

After enabling the strict checking mode, verify that
the strict mode has really been enabled by querying
the MCE.

If the mode is found to be disabled, the code should
assert.

Change-Id: I113ec8decb737f8208059a2a3ba3076fad77890e
Signed-off-by: Anthony Zhou <anzhou@nvidia.com>

MMIO writes should verify that the writes actually went through.
Read the value back after the write operation, perform assert
if the read back value is not same as the write value.

Change-Id: Id2ceb014116f3aa6a9e86505ca1ae9911470a679
Signed-off-by: Anthony Zhou <anzhou@nvidia.com>

During boot the platform enables dual execution for Xavier CPUs.
This patch reads back the ACTLR_ELx register to verify that the bit
is actually set. It asserts if the bit is not set.

Change-Id: I5ba9491ced86285d307b95efa647a427ff77c79e
Signed-off-by: Kalyani Chidambaram Vaidyanathan <kalyanic@nvidia.com>

The firewall settings for the hardware resources are present in the
Security Configuration Registers. The firewall settings are programmed
by other software components and so must be verified for correctness
before touching the hardware resources they protect.

This patch reads the firewall settings during early boot and asserts
if the settings mismatch.

Change-Id: I53cc9aeadad32e54e460db0fa2c38e46bcc92066
Signed-off-by: Kalyani Chidambaram Vaidyanathan <kalyanic@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch removes the unused interrupt mapping for AON_WDT
for all Tegra194 platforms.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I475a1e83f809c740e62464b5b4e93cb0a2e33d6b

This patch verifies that the binary image is compatible with
chip ID of the platform.

Change-Id: I28db221b4442aa8827a092faadf32f110d7c5cb4
Signed-off-by: kalyanic <kalyanic@nvidia.com>

This patch adds all Tegra194 RAS nodes definitions and support to
handle all uncorrectable RAS errors.

Change-Id: I109b5a8dbca91d92752dc282c4ca30f273c475f9
Signed-off-by: David Pu <dpu@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch enables SDEI support for all Tegra platforms, with
the following configuration settings.

* SGI 8 as the source IRQ
* Special Private Event 0
* Three private, dynamic events
* Three shared, dynamic events
* Twelve general purpose explicit events

Verified using TFTF SDEI test suite.

******************************* Summary *******************************
 Test suite 'SDEI'                                               Passed
 =================================
 Tests Skipped : 0
 Tests Passed  : 5
 Tests Failed  : 0
 Tests Crashed : 0
 Total tests   : 5
 =================================
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I1922069931a7876a4594e53260ee09f2e4f09390

This patch enables the Exception Handling Framework to service the WDT
interrupts on all Tegra platforms.

Verified that the watchdog timer interrupt fires after migrating to
the EHF.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I6b2e33da7841aa064e3a8f825c26fadf168cd0d5

This patch enables dual execution optimized translations for EL2 and EL3
CPU exception levels.

Change-Id: I28fe98bb05687400f247e94adf44a1f3a85c38b1
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Since now the generic console_t structure holds the UART base address as
well, let's use that generic location and drop the UART driver specific
data structure at all.

Change-Id: I75dbfafb67849833b3f7b5047e237651e3f553cd
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Since now the generic console_t structure holds the UART base address as
well, let's use that generic location and drop the UART driver specific
data structure at all.

Change-Id: Ifd6aff1064ba1c3c029cdd8a83f715f7a9976db5
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Since now the generic console_t structure holds the UART base address as
well, let's use that generic location and drop the UART driver specific
data structure at all.

Change-Id: I5c2fe3b6a667acf80c808cfec4a64059a2c9c25f
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Tegra210 SoCs need the sc7entry-fw to enter System Suspend mode,
but there might be certain boards that do not have this firmware
blob. To stop the NS world from issuing System suspend entry
commands on such devices, we ned to disable System Suspend from
the PSCI "features".

This patch removes the System suspend handler from the Tegra PSCI
ops, so that the framework will disable support for "System Suspend"
from the PSCI "features".

Original change by: kalyani chidambaram <kalyanic@nvidia.com>

Change-Id: Ie029f82f55990a8b3a6debb73e95e0e218bfd1f5
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch enables the GPCDMA for all Tegra194 platforms to help
accelerate all the memory copy operations.

Change-Id: I8cbec99be6ebe4da74221245668b321ba9693479
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

Many simulation/emulation platforms do not support this hardware block
leading to SErrors during register accesses.

This patch conditionally accesses the registers from this block only
on actual Si and FPGA platforms.

Change-Id: Ic22817a8c9f81978ba88c5362bfd734a0040d35d
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch organizes the platform memory/mmio map, so that the base
addresses for the apertures line up in ascending order. This makes
it easier for the xlat_tables_v2 library to create mappings for each
mmap_add_region call.

Change-Id: Ie1938ba043820625c9fea904009a3d2ccd29f7b3
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

The previous bootloader is not able to pass boot params wider than
32-bits due to an oversight in the scratch register being used. A
new secure scratch register #75 has been assigned to pass the higher
bits.

This patch adds support to parse the higher bits from scratch #75
and use them in calculating the base address for the location of
the boot params.

Scratch #75 format
====================
31:16 - bl31_plat_params high address
15:0 - bl31_params high address

Change-Id: Id53c45f70a9cb370c776ed7c82ad3f2258576a80
Signed-off-by: Steven Kao <skao@nvidia.com>

This patch adds support to toggle SE clock, using the bpmp_ipc
interface, to enable SE context save/restore. The SE sequence mostly
gets called during System Suspend/Resume.

Change-Id: I9cee12a9e14861d5e3c8c4f18b4d7f898b6ebfa7
Signed-off-by: steven kao <skao@nvidia.com>

This patch adds a new configuration option to the platform makefiles
that disables/enables strict checking mode. The config is enabled
by default.

Change-Id: I727dd0facee88d9517bf6956eaf9163eba25c8bb
Signed-off-by: Steven Kao <skao@nvidia.com>

The stream IDs for XUSB programmed during cold boot are lost on System
Suspend. This patch restores the XUSB stream IDs on System Resume.

NOTE: THE WARMBOOT CODE NEEDS TO MAKE SURE THAT THE XUSB MODULE IS OUT
OF RESET AND THE CLOCKS ARE ENABLED, BEFORE POWERING ON THE CPU, DURING
SYSTEM RESUME.

Change-Id: Ibd5f1e5ebacffa6b29b625f4c41ecf204afa8191
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch introduces the 'plat_enable_console' handler to allow
the platform to enable the right console. Tegra194 platform supports
multiple console, while all the previous platforms support only one
console.

For Tegra194 platforms, the previous bootloader checks the platform
config and sets the uart-id boot parameter, to 0xFE. On seeing this
boot parameter, the platform port uses the proper memory aperture
base address to communicate with the SPE. This functionality is
currently protected by a platform macro, ENABLE_CONSOLE_SPE.

Change-Id: I3972aa376d66bd10d868495f561dc08fe32fcb10
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

"Strict checking" is a mode where secure world can access
secure-only areas unlike legacy mode where secure world could
access non-secure spaces as well. Secure-only areas are defined
as the TZ-DRAM carveout and any GSC with the CPU_SECURE bit set.
This mode not only helps prevent issues with IO-Coherency but aids
with security as well.

This patch implements the programming sequence required to enable
strict checking mode for Tegra194 SoCs.

Change-Id: Ic2e594f79ec7c5bc1339b509e67c4c62efb9d0c0
Signed-off-by: Dilan Lee <dilee@nvidia.com>

This patch cleans up all references to the Tegra186 family of SoCs.

Change-Id: Ife892caba5f2523debacedf8ec465289def9afd0
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch renames all the secure scratch registers to reflect
their usage.

This is a list of all the macros being renamed:

- SECURE_SCRATCH_RSV44_* -> SCRATCH_BOOT_PARAMS_ADDR_*
- SECURE_SCRATCH_RSV97 -> SCRATCH_SECURE_BOOTP_FCFG
- SECURE_SCRATCH_RSV99_* -> SCRATCH_SMMU_TABLE_ADDR_*
- SECURE_SCRATCH_RSV109_* -> SCRATCH_RESET_VECTOR_*

Change-Id: I838ece3da39bc4be8f349782e99bac777755fa39
Signed-off-by: Steven Kao <skao@nvidia.com>

Main fixes:

Fix invalid use of function pointer [Rule 1.3]

Added explicit casts (e.g. 0U) to integers in order for them to be
compatible with whatever operation they're used in [Rule 10.1]

convert object type to match the type of function parameters
[Rule 10.3]

Force operands of an operator to the same type category [Rule 10.4]

Fix implicit widening of composite assignment [Rule 10.6]

Fixed if statement conditional to be essentially boolean [Rule 14.4]

Added curly braces ({}) around if statements in order to
make them compound [Rule 15.6]

Voided non c-library functions whose return types are not used
[Rule 17.7]

Change-Id: I65a2b33e59aebb7746bd31544c79d57c3d5678c5
Signed-off-by: Anthony Zhou <anzhou@nvidia.com>

Introduce platform handlers to reprogram the MSS settings.

Change-Id: Ibb9a5457d1bad9ecccea619d69a62bed3bf7d861
Signed-off-by: Puneet Saxena <puneets@nvidia.com>
Signed-off-by: Krishna Reddy <vdumpa@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch updates the total number of CPU clusters and number
of cores per cluster, in the platform makefile.

Change-Id: I569ebc1bb794ecab09a1043511b3d936bf450428
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

T194 XUSB has support for XUSB virtualization. It will have one
physical function (PF) and four Virtual function (VF)

There were below two SIDs for XUSB until T186.
1) #define TEGRA_SID_XUSB_HOST    0x1bU
2) #define TEGRA_SID_XUSB_DEV    0x1cU

We have below four new SIDs added for VF(s)
3) #define TEGRA_SID_XUSB_VF0    0x5dU
4) #define TEGRA_SID_XUSB_VF1    0x5eU
5) #define TEGRA_SID_XUSB_VF2    0x5fU
6) #define TEGRA_SID_XUSB_VF3    0x60U

When virtualization is enabled then we have to disable SID override
and program above SIDs in below newly added SID registers in XUSB
PADCTL MMIO space. These registers are TZ protected and so need to
be done in ATF.
a) #define XUSB_PADCTL_HOST_AXI_STREAMID_PF_0 (0x136cU)
b) #define XUSB_PADCTL_DEV_AXI_STREAMID_PF_0  (0x139cU)
c) #define XUSB_PADCTL_HOST_AXI_STREAMID_VF_0 (0x1370U)
d) #define XUSB_PADCTL_HOST_AXI_STREAMID_VF_1 (0x1374U)
e) #define XUSB_PADCTL_HOST_AXI_STREAMID_VF_2 (0x1378U)
f) #define XUSB_PADCTL_HOST_AXI_STREAMID_VF_3 (0x137cU)

This change disables SID override and programs XUSB SIDs in
above registers to support both virtualization and non-virtualization.

Change-Id: I38213a72999e933c44c5392441f91034d3b47a39
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>

This patch removes the code to enable L2 ECC parity protection
bit, as Tegra194 does not have any Cortex-A57 CPUs.

Change-Id: I4b56595fea2652e8bb8ab4a7ae7567278ecff9af
Signed-off-by: Harvey Hsieh <hhsieh@nvidia.com>

This patch implements the platform handler to return the pointer
to the power domain tree.

Change-Id: I74ea7002c7a461a028b4a252bbd354256fdc0647
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch adds support for all three SMMU devices present on the SoC.

The following changes have been done:
    Add SMMU devices to the memory map
    Update register read and write functions

Change-Id: I0007b496d2ae7264f4fa9f605d4b0a15fa747a0f
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>

This patch creates the base commit for the Tegra194 platform, from
Tegra186 code base.

Change-Id: I1c77e4984f7ff39655f3fb79633d13d533707ede
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch initilises the per-CPU GIC bits during cold boot and
secondary CPU power up. Commit 80c50eea

 accidentally left out this
part.

Change-Id: I73ce59dbc83580a84b827cab89fe7e1f65f9f130
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch organizes the memory and mmio maps linearly, to make the
mmap_add_region process faster. The microsecond timer has been moved
to individual platforms instead of making it a common step, as it
further speeds up the memory map creation process.

Change-Id: I6fdaee392f7ac5d99daa182380ca9116a001f5d6
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>

This patch renames all the secure scratch registers to reflect their
usage.

This is a list of all the macros being renamed:

- SECURE_SCRATCH_RSV1_* -> SCRATCH_RESET_VECTOR_*
- SECURE_SCRATCH_RSV6 -> SCRATCH_SECURE_BOOTP_FCFG
- SECURE_SCRATCH_RSV11_* -> SCRATCH_SMMU_TABLE_ADDR_*
- SECURE_SCRATCH_RSV53_* -> SCRATCH_BOOT_PARAMS_ADDR_*
- SECURE_SCRATCH_RSV55_* -> SCRATCH_TZDRAM_ADDR_*

NOTE: Future SoCs will have to define these macros to
      keep the drivers functioning.

Change-Id: Ib3ba40dd32e77b92b47825f19c420e6fdfa8b987
Signed-off-by: Steven Kao <skao@nvidia.com>

MISRA Rule 8.4, A compatible declaration shall be visible when an
object or function with external linkage is defined.

This patch adds static for local array to fix this defect.

Change-Id: I8231448bf1bc0b1e59611d7645ca983b83d5c8e3
Signed-off-by: Anthony Zhou <anzhou@nvidia.com>

Main fixes:

Added explicit casts (e.g. 0U) to integers in order for them to be
compatible with whatever operation they're used in [Rule 10.1]

Force operands of an operator to the same type category [Rule 10.4]

Added curly braces ({}) around if statements in order to
make them compound [Rule 15.6]

Change-Id: I4840c3122939f736113d61f1462af3bd7b0b5085
Signed-off-by: Anthony Zhou <anzhou@nvidia.com>

This patch adds capability to read the boot flag to enable L2 ECC
and Parity Protection bit for the Cortex-A57 CPUs. The previous
bootloader sets this flag value for the platform.

* with some coverity fix:
MISRA C-2012 Directive 4.6
MISRA C-2012 Rule 2.5
MISRA C-2012 Rule 10.3
MISRA C-2012 Rule 10.4

Change-Id: Id7303bbbdc290b52919356c31625847b8904b073
Signed-off-by: Harvey Hsieh <hhsieh@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>